CABLE WINCH PULLER 36700 - 2 TON CABLE WINCH PULLER 36701 - 4 TON CABLE WINCH PULLER *Actual product may vary slightly Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property damage and/or personal injury. Please keep instructions for future reference. For warranty purchases, please keep your dated proof of purchase.
IMPORTANT SAFETY INFORMATION TO PREVENT SERIOUS INJURY AND DEATH: BASIC SAFETY INFORMATION 1. Do not pull more than rated load. Be aware of dynamic loading! Sudden load movement may briefly create excess load causing product failure. 2. Do not operate while puller restricted from forming a straight line with loading direction. 3. Do not operate puller with twisted, kinked, or damaged wire rope. Inspect wire rope carefully before every use. 4. Do not operate a damaged or malfunctioning puller.
SPECIFICATIONS Item No. Rated Capacity Cable Length 36700 4,000 lb. 10’ Item No. Rated Capacity Cable Length 36701 8,000 lb. 12’ SETUP INSTRUCTIONS Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product. Note: For additional information regarding the parts listed in the following pages, refer to Parts List and Diagram on page 9. 1.
5. Do not use the wire rope as a ground for welding. Do not touch a welding electrode to the wire rope. 6. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 7. There must not be objects, such as utility lines, nearby that will present a hazard while working. 8. Inspect the puller as explained in Frequent Inspection on page 8 after setup but before use.
. Release the Stop Pawl Trigger. 6. Do not wrap the puller wire rope around the load. 7. Attach the load to the load hook securely by properly rated, suitable means, such as chains, shackles, hooks, lifting slings, etc. Load must be attached to prevent accidental disconnection. 8. Properly seat the sling or other device in the base (bowl or saddle) of the hook (see the left side diagram on Figure F). Do not allow the hook hitch to support any part of the load. Figure F: Correct and incorrect 9.
d. Repeat this action, as needed, until the tension on the wire rope eases. e. Pull on the STOP PAWL TRIGGER to release it from the cam and gently pull back on the tool to get wire rope slack and free it from the load. 5. To prevent entangling of the wire rope onto the drum, with the Load Hook still attached to the load, push the spring into its “Down” position. Hold the Anchor hook in one hand. While gently pulling against the load, swing the Handle back and forth to rewind the wire rope.
5. Check wire rope reeving. 6. Check puller lever for bends, cracks, or other damage. 7. Check for damage to the support for the puller. WARNING! TO PREVENT SERIOUS INJURY FROM PULLER FAILURE: Do not use damaged equipment. If any defect or damage is noted, have the problem corrected before further use. PERIODIC (THOROUGH) INSPECTION A qualified technician should perform the procedures in this section AT LEAST YEARLY. Inspection is needed more often for heavily used pullers.
MAINTENANCE 1. Repair or replacement of puller components must be performed only by a qualified technician using only identical replacement parts with the same rating. 2. Operating mechanisms, pawls, and brakes may require adjustment. 3. Note the following regarding specific components: a. Replace damaged or worn hooks. Do not repair them by welding or reshaping. b. Replace excessively worn braking components such as friction disks, ratchets, pawls, and pawl springs. c.
PARTS LIST AND DIAGRAM PARTS LIST Part 1 2 3 4 Description Hook Frame Stop Pawl Spring Stop Pawl Trigger Part 5 6 7 8 Description Ratchet Drive Pawl Guard Drive Pawl Spring Part 9 10 11 Description Wire Rope Lever Load Hook ASSEMBLY DIAGRAM 1 2 3 5 6 8 4 customerservice@focus-ontools.
Limited Manufacturer Warranty FOT makes every effort to ensure that this product meets high quality and durability standards. FOT warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials. Warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or accidents, repairs or alterations, or a lack of maintenance.