Use and Care Manual

ManualsBrandsSteel Core ManualsJig Saws3.5 Amp Corded Electric Jig Saw Tool with Variable Speed Capability

For Customer Service, Call 1-800-348-5004

or e-mail customerservice@focus-ontools.com

33186 12/2017

3.5 AMP ELECTRICAL JIG SAW TOOL

33186

*Actual product may vary slightly

Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product.

Observe all safety information to protect yourself and others. Failure to observe the instructions may result in property

damage and/or personal injury. Please keep instructions for future reference.

For warranty purchases, please keep your dated proof of purchase. File or attach to the manual for safe keeping.

This product can expose you to chemicals including

LEAD/CADMIUM/DEHP, which is

known to the State

of California to cause cancer and birth defects or

other reproductive harm. For more information go

to www.P65Warnings.ca.gov.

WARNING

Summary of content (11 pages)

PAGE 1
33186 3.5 AMP ELECTRICAL JIG SAW TOOL WARNING This product can expose you to chemicals including LEAD/CADMIUM/DEHP, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. *Actual product may vary slightly Please carefully read and save these instructions before attempting to assemble, maintain, install, or operate this product. Observe all safety information to protect yourself and others.
PAGE 2
SPECIFICATIONS Rated Voltage 120V Rated Frequency 60HZ Input Current 3.5A No-Load Speed 500-3,000 SPM Stroke Length 3/4 IN. Cutting Capacities Wood max. ：2 IN. Steel max. ：1/8 IN. Cutting Angles 45 degrees left, 45 degrees right (90 degrees) GENERAL SAFETY RULES WORK AREA Keep your work area clean and well lit. Cluttered benches and dark area invite accidents Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
PAGE 3
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. Do not expose power tools to rain or wet conditions. Water entering a power tools will increase the risk of electric shock. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immediately.
PAGE 4
TOOL USE AND CARE Use clamps or other practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body is unstable and may lead to loss of control. Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer at the rate for which it is designed. Do not use the tool if its switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must be repaired.
PAGE 5
SERVICE Tool service must be performed only by qualified personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury.
PAGE 6
FUNCTIONAL DESCRIPTION AND ASSEMBLY 1. Speed Dial Switch 2. On/Off Switch 3. Locking Button 4. Transparent Blade Guard 5. Heavy-Duty Cord 6. Hex Wrench 7. Base Plate BLADE INSTALLATION Warning: Before installing or changing a blade, be sure that the saw is unplugged from the power supply. 1. Loosen the two blade lock bolts (use hex key supplied) enough for a blade to be removed or inserted (Fig. 1). 2. Insert the blade in slot with teeth facing forward.
PAGE 7
Use Of The Ball Turn the bolts on the base plate counterclockwise to loosen the positioner with the hex wrench. Slide the positioner forward until the ball touches the saw blade. However when using a saw blade with crooked back, the positioner should be moved back to keep the ball from touching the blade. Note: When cutting iron plate or synthetic plate etc, please use lube or cutting oil between the saw blade and the ball.
PAGE 8
Continuous rotation When pressing the on/off switch, use the locking button to enable the tool to be operated continuously. Press the on/off switch again and the lock button will be unlocked at once. Bevel cutting Warning! Before adjusting the cutting angles, be sure that the saw is unplugged from the power supply. The base plate can be tilted to cut any angle between 0 and 45 degrees right and left. Loosen the base plate adjustment screw (Fig.
PAGE 9
Plug-in cutting If the cutting is not started from the side of the workpiece or no holes has been drilled before hand, plug-in cutting is then needed. First start the tool and locate the back side of the bottom plate slowly. Lower the front part with the running saw blade to touch the workpiece slightly. Cut through the workpiece gradually until the bottom plate lies on the workpiece. The jig saw is now for normal use.
PAGE 10
ASSEMBLY customerservice@focus-ontools.
PAGE 11
PART LIST Description Part No. Description Part No. 1 Speed control PCB 18 Slid mass 2 Switch 19 Slid rod 3 Screw ST4.2 x 19 20 Felt 4 Right half housing 21 Blade clamp 5 Cord clip 22 Screw ST4 x 15 6 Screw ST4.