INSTRUCTION MANUAL MODEL: STC-GXATW V.
**IMPORTANT NOTE** To ensure the product is being utilized to its full potential, we recommend checking our website for new product updates. If your unit is having trouble, please check the website to determine you are using the latest firmware or software version. TECHNICAL SUPPORT EMAIL: Stealthcam@gsmorg.com Please allow 48 hours for email response. STEALTH CAM P.O. Box 535189 Grand Prairie, TX 75053-‐9504 www.
TABLE OF CONTENTS Camera Overview General Information / Specifications Switch / Button Functions On-Screen Display Functions & Features Camera Settings Advanced Settings Cellular Settings Memory Card Installation Formatting Battery Removal & Installation Definitions Frequently Asked Questions (FAQs) FCC Compliance Limited Warranty Information www.stealthcam.
CAMERA OVERVIEW (NOTE: You’ll need to screw the supplied antenna into the top of the camera.) NOTE: You will find your Serial # under the weather seal gasket toward the bottom of the camera. www.stealthcam.
CAMERA OVERVIEW (cont.) Battery Compartment (12 ‘AA’ – 6 on both sides) www.stealthcam.
GENERAL INFORMATION ! ! ! ! ! Operating Environment: 14 to 104 deg F (-10 to 40 deg C). 20-85% relative humidity, non-condensing. The camera is designed to be weather resistant. Never attempt to immerse the unit in water or any other liquid. This will damage the unit and void the warranty. Do not mix old and new batteries. Do not mix alkaline, standard, or rechargeable batteries. Use a soft lens cloth for cleaning lens.
SWITCH / BUTTON FUNCTIONS 3 Position Switch ! ! ! OFF position: The unit will be OFF when the switch is in this position. ON position: The unit is now ON, defaults to Qset1 on first power up. After each time the camera is turned ON, the unit will remember the previous mode and settings. TEST position: This position is to test the PIR sensor.
ON-‐SCREEN DISPLAY ICONS Quick Sets (QSET) While in any Quick Set Mode, the LCD screen will display the Qset that the camera is currently set to in the top left corner. The bottom half of the screen will give a digital read out of how the camera is preprogrammed. It will scroll across the display like below: PHOTO...8.0MP...30 S DELAY...
FUNCTIONS & FEATURES Quick Sets (QSET) ! QSET 1 The unit will be set to the following settings: o o o o o o Operational Mode: PIR Photo Photo Resolution: 8.0 MP PIR Delay: 30 seconds Burst Mode: 3 Photos Reduce Blur: ADVANCED Info Bar: ON Scrolling Text PHOTO...8.0MP...30 S DELAY...3 PHOTO BURST ! QSET 2 The unit will be set to the following settings: o o o o o o Operational Mode: PIR Photo Photo Resolution: 8.
CAMERA SETUP Setup Date: Set the Date for the camera. ! The default date is 01/01/18 Setup Time: Set the Time for the camera. ! The default time is 12:00AM Time Zone: Set the Time Zone where you’re using the camera. ! Eastern ! Central (Default) ! Mountain ! Pacific ! Alaskan ! Hawaiian Time Format: Set whether the time will be kept using a 12 Hour format or 24 Hour format.
CAMERA SETUP (cont.) ! Time Lapse: Camera takes a still image per preset time. o Time Lapse Settings are: Photo Resolution, PIR Delay, Time Lapse Delay, Time Lapse Start, Time Lapse Stop, Blur Reduction, Camera Name, Temperature, Information Bar, Latitude, Longitude, Factory Reset, Security Key, Format SD Card, Software Upgrade. o Time Lapse Photos will be marked with “TL” in the Information Bar.
CAMERA SETUP (cont.) Operating Hours (Default – 24/7): This setting tells the camera what specific hours to operate “scheduled” or to “always” be on. o 24/7 o Scheduled ! Start (Default - 08:00AM) o Time ranges from 00:00 to 23:59 [HH:MM] ! End (Default - 05:00PM) o Time ranges from 00:00 to 23:59 [HH:MM] NOTE: Activity Start/End settings are visible only if Scheduled is selected ! ! Photo Resolution (Default – 8.
CAMERA SETUP (cont.) ! Reduce Blur (Default – Advanced) o ADVANCED – This setting will use a maximum exposure time of 1/30sec for the night photos. Other adjustments are made to increase the brightness and clarity of the photo. o STANDARD – This setting will use a maximum exposure time of 1/15sec for the night photos. ! Photo Burst (Default – 1 Photo) o Capturing options will be 1 to 9 images with a 1.0 sec delay.
CAMERA SETUP (cont.) Options only if in Time Lapse Mode. ! Time Lapse Delay – to set the delay between photos. o Will display as “TL DELAY” in Camera Setup. o The camera will take PIR photos during the Time Lapse Session when the Time Lapse Delay is set to 60 seconds or greater. o The Time Lapse range is from 5 seconds to 59 minutes and 59 seconds. o The default Time Lapse Setting is 30 seconds.
CAMERA SETUP (cont.) Options only if in Video Mode. ! Video Resolution (Default – 1280x720) o 1280 x 720 o 640 x 352 NOTE: If Cellular Modem is set to ON, then the PIR Video mode has special settings. ! 320x176 ! Video Length (Default - 10 sec) o Set the video length from 10 to 180 seconds in 5-second increments.
ADVANCED SETTINGS ! Temperature (Default – Fahrenheit) o The temperature is imprinted on each photo in either Celsius or Fahrenheit. ! Information Bar (Default – ON) o The Stealth Cam logo, Time, Date, Temperature Moon Phase, and Camera Name are imprinted on the bottom of each picture.
ADVANCED SETTINGS (cont.) The icons for the moon phase are as follows (see Symbol): www.stealthcam.
ADVANCED SETTINGS (cont.) ! Latitude: This function will allow the user to manually set the latitude coordinates for the camera. o The default coordinates will be 000.000000 N, this number can be set to 000.000000 -‐ 179.999999 N or S. ! Longitude: This function will allow the user to manually set the longitude coordinates for the camera. o The default coordinates will be 000.000000 E, this number can be set to 000.000000 -‐ 179.
CELLULAR SETTINGS The camera has the ability to communicate with generic cellular towers and transmit data from the camera to the Remote Application (APP) where you can see your photos, videos or change the settings on your cameras remotely. The APP works with your camera and mobile device is available for download from either the Apple App Store or the Android Play Store.
CELLULAR SETTINGS (cont.) ! Note: If the network is not found, then follow these steps. Press Enter, then Enter again at the APN screen. Do not enter any information on these screens. This will allow the camera to attempt to find a network again. If after three attempts to connect to the network fails, please contact our Customer Service Dept for assistance. ! Note: If the Account is not found, then follow these steps.
CELLULAR SETTINGS (cont.) ! Account: The user must enter in their account user name and password that is setup on the APP. Without a user name and password the camera will not connect to the APP. Use arrow keys to alter text. o User Name o Password ! Cellular Modem: This setting controls the cellular modem.
CELLULAR SETTINGS (cont.) ! Upload Limit: This setting controls the amount of data sent to App per day. This allows the camera to not exceed a cellular carrier’s data plan limit. o Unlimited (Default) o 500MB o 250MB o 100MB o 10MB ! Location Data: The user can choose to use the cellular tower’s location data for the Longitude and Latitude settings on the camera.
CELLULAR SETTINGS (cont.) ! APN Name: The Access Point Name (APN) is the name your camera needs to set up a connection to the gateway between your carrier's cellular network and the public Internet. This setting is normally automaticallty determined during the Setup Wizard. Please consult customer service before manually changing this setting.
MEMORY CARD INSTALLATION To insert the SD memory card into the camera: first locate the SD card slot on the right hand side of the of the camera case. Next with the SD card label facing towards the front of the camera, insert the SD card. When the card has been pressed in fully there will be a noticeable resistance as the spring locking mechanism activates to hold on the SD card.
FORMATTING SD CARD It always best to format your SD cards from the actual device you are using, in this case the camera. This will allow the camera to format the card in the proper fashion. 1. Insert SD card into the camera. 2. Turn the camera power ON. 3. Press the MENU button. 4. Navigate to “Camera Settings”. Press ENTER. 5. Navigate to "Format Card". Press ENTER. 6. Navigate to "Yes". Press ENTER. 7.
BATTERY REMOVAL & INSTALLATION To remove the batteries from the unit; open the case and press the EJECT button on the lower right hand corner. This will cause the battery tray to be released and slide downwards. New, Alkaline or Lithium, ‘AA’ batteries must be inserted with the orientation as shown on the tray.
DEFINITIONS REFLEX (Sub 1-‐Second Trigger) – Ultra-‐fast trigger speed. Never miss a crucial moment. MATRIX (Blur Reduction Technology) – Advanced blur reduction dramatically reduces blur effects resulting in sharper, clearer images. RETINA (Advanced Low-‐Light Sensitivity) – Superior low light performance for extended nighttime range. MULTI-‐ZONE DETECTION -‐ Provides for more accurate coverage at angle and distance.
FREQUENTLY ASKED QUESTIONS (FAQs) Q: Where do I locate the serial number on a Stealth Cam G, P, RX, and GX series cameras? A: Under the weather seal gasket that pinches between the back of the camera and the door, on the bottom of the camera. Q: What should the trigger speed be on my stealth camera? A: This varies depending on the model of the camera.
FREQUENTLY ASKED QUESTIONS (cont) Q: Can I swap SD cards from one scouting camera to another? A: No, We do not recommend swapping SD cards between different cameras. Each camera is made with different formatting capabilities and can cause the camera not to recognize the SD card. Q: Can I use a Mini SD card in my camera? A: No, we do not recommend a Mini SD card for storing your files.
FCC COMPLIANCE GSM STC-GXATW This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.
LIMITED WARRANTY INFORMATION Your Stealth Cam scouting camera is covered by a 365 Day Limited Warranty on parts and labor from the date of original purchase, and purchases must be made through an authorized dealer. The warranty covers defects in workmanship and materials. The warranty does not apply to units, which have been damaged or abused intentionally or unintentionally.
MANUEL D'INSTRUCTIONS MODÈLE : STC- GXATW V.01 www.stealthcam.
**NOTE IMPORTANTE** Pour vous assurer que le produit soit utilisé à son plein potentiel, nous vous recommandons de vérifier notre site Web pour obtenir les nouvelles mises à jour du produit. Si votre appareil a des problèmes, veuillez consulter le site pour déterminer si vous utilisez le dernier Minilogiciel ou la toute dernière version du logiciel. SOUTIEN TECHNIQUE COURRIEL : stealthcam@gsmorg.
TABLE DES MATIÈRES APERÇU DE L'APPAREIL PHOTO INFORMATIONS GÉNÉRALES / CARACTÉRISTIQUES SWITCH / FONCTIONS DES BOUTONS À L'ÉCRAN Icônes d'Affichage FONCTIONS ET CARACTÉRISTIQUES CONFIGURATION DE LA CAMERA REGLAGES ACANCES PARAMèTRES DU CELLULAIRE CARTE MÉMOIRE INSTALLATION FOMATAGE DE LA CARTE SD INSTALLATION ET RETRAIT DE LA PILE DÉFINITIONS FOIRE AUX QUESTIONS (FAQ) CONFORMITÉ FCC RENSEIGNEMENTS SUR LA GARANTIE LIMITÉE www.stealthcam.
APERÇU DE L'APPAREIL PHOTO NOTE: Vous trouverez votre N ° de série sous le joint d'étanchéité de la météo vers le bas de la caméra. www.stealthcam.
APERÇU DE L'APPAREIL PHOTO (SUITE) Arrière www.stealthcam.
INFORMATIONS GÉNÉRALES ! ! ! ! ! ! ! ! ! ! ! Environnement de fonctionnement: de 14 à 104 ° F (X 10 à 40 ° C). Humidité relative de 20 à 85%, sans condensation. instructions de soins spéciaux !! L'appareil photo est conçu pour être résistant aux intempéries. Ne essayez jamais d'immerger l'unité dans l'eau ou tout autre liquide. Cela pourrait endommager l'appareil et annuler la garantie. Ne pas mélanger piles neuves et anciennes.
SWITCH / FONCTIONS DES BOUTONS 6 Interrupteur de position ! ! ! Position OFF: L'appareil sera éteint lorsque l'interrupteur est dans cette position. Position ON: L'unité est maintenant activée, par défaut à Qset1 lors de la première mise sous tension. Après chaque mise sous tension de l'appareil photo, l'appareil mémorise le mode et les réglages précédents. Position TEST: Cette position sert à tester le capteur PIR.
À L'ÉCRAN ICôNES D'AFFICHAGE Ensembles rapides (QSET) En mode Quick Set, l'écran LCD affiche le Qset sur lequel la caméra est actuellement réglée dans le coin supérieur gauche. La moitié inférieure de l'écran donnera une lecture numérique de la façon dont l'appareil photo est préprogrammé. Il fera défiler l'affichage comme ci-dessous: PHOTO ... 8.0MP ... 30 S Délais ...
FONCTIONS ET CARACTÉRISTIQUES ! QSet 1 L'unité sera réglé sur les paramètres suivants: o Mode opérationnel: PIR photo o Résolution photo: 8,0 MP o PIR Délai: 30 secondes o Mode rafale: 3 Photos o Réduire le flou: ADVANCED o Info Bar: ON ! QSet 2 L'unité sera réglé sur les paramètres suivants: o Mode opérationnel: PIR photo o Résolution photo: 8,0 MP o PIR Délai: 30 secondes o Mode rafale: 1Photo o Réduire le flou: ADVANCED o Info Bar: ON ! Q
CONFIGURATION DE LA CAMERA Si le bouton Menu est pressée alors que dans le mode de configuration de la caméra, la caméra passe en mode Auto. Date de configuration: Fixer la date de l'appareil photo. ! La date par défaut est 01/01/18 Time: Réglez le temps pour l'appareil photo. ! La durée par défaut est 00:00 Fuseau horaire: Définition du fuseau horaire où vous utilisez l'appareil photo.
CONFIGURATION DE LA CAMERA (suite.) Time Lapse: L'appareil photo prend une image fixe par unité de temps prédéfini. o Time Settings Accéléré sont: Photo Résolution, PIR Delay, Accéléré Delay, Accéléré Démarrer, Accéléré Stop, Réduction du flou, Nom de la caméra, la température, la barre d'informations, Latitude, Longitude, Réinitialisation usine, la clé de sécurité, Format SD Card, Software Mettre à niveau.
CONFIGURATION DE LA CAMERA (suite.) ! ! Heures de fonctionnement (par défaut - 24/7): Ce paramètre indique la caméra ce que heure spécifique à fonctionner "prévue" ou "toujours" être sur.
CONFIGURATION DE LA CAMERA (suite.) ! Réduire le flou (par défaut - Advanced) o ADVANCED - Ce paramètre va utiliser un temps d'exposition maximum de 1 / 30sec pour les photos de nuit. Autres ajustements sont effectués pour augmenter la luminosité et la clarté de la photo. o STANDARD - Ce paramètre va utiliser un temps d'exposition maximum de 1 / 15sec pour les photos de nuit.
CONFIGURATION DE LA CAMERA (suite.) En option seulement si en mode Time lapse. ! Accéléré Delay -‐ Pour définir le délai entre les photos. o Se affiche comme "DELAY TL» dans les réglages de l'appareil photo. o L'appareil photo attendre un certain laps de temps entre les photos Accéléré. o L'appareil photo prend des photos pendant la PIR Accéléré session lorsque le Accéléré délai est de 60 secondes ou plus.
CONFIGURATION DE LA CAMERA (suite.) En option seulement si en Vidéo Mode. ! Résolution de la vidéo (par défaut - 1280x720) o 1280 x 720 o 640 x 352 ! Durée de la vidéo (par défaut - 10 sec) o Régler la longueur de la vidéo de 10 à 180 secondes, par incréments de 5 secondes.
CONFIGURATION DE LA CAMERA (suite.) ! Température (par défaut -‐ Fahrenheit) o La température est imprimé sur chaque photo en degrés Celsius ou Fahrenheit. ! Barre d'informations (par défaut -‐ ON) o Le logo Stealth Cam, heure, date, Température Phase de Lune, et le nom de l'appareil photo sont imprimées sur le fond de chaque image.
CONFIGURATION DE LA CAMERA (suite.) Les icônes de la phase de lune sont les suivantes (voir Symbole): www.stealthcam.
CONFIGURATION DE LA CAMERA (suite.) Latitude: Cette fonction permet à l'utilisateur de régler manuellement les coordonnées de latitude pour la caméra. o Les coordonnées par défaut seront 000.000000 N, ce nombre peut être réglé sur 000.000000 -‐ 179.999999 N ou S. ! ! Longitude: Cette fonction permet à l'utilisateur de régler manuellement les coordonnées de longitude pour la caméra. o Les coordonnées par défaut seront 000.
PARAMèTRES DU CELLULAIRE La caméra a la capacité de communiquer avec les tours de téléphonie cellulaire génériques et transmettre des données de la caméra à l'application à distance (APP) où vous pouvez voir vos photos, vidéos ou modifier les paramètres sur vos caméras à distance.
PARAMèTRES DU CELLULAIRE (suite.) Remarque: Si le réseau est introuvable, puis suivez ces étapes. Sélectionnez Suivant, puis une fois à l'écran APN. Cela permettra à l'appareil pour tenter de trouver de nouveau un réseau. Si après trois tentatives de connexion au réseau échoue, s'il vous plaît communiquer avec notre service à la clientèle Département de l'aide. Remarque: Si le compte n'est pas trouvé, procédez comme suit.
PARAMèTRES DU CELLULAIRE (suite.) ! Compte: L'utilisateur doit entrer dans leur nom d'utilisateur et mot de passe qui est configuré sur l'APP. Sans un nom d'utilisateur et mot de passe de la caméra ne se connecte pas à l'APP. Utilisez les touches fléchées pour modifier le texte. o Nom d'utilisateur o Mot de passe ! Modem cellulaire: Ce paramètre contrôle le modem cellulaire.
PARAMèTRES DU CELLULAIRE (suite.) ! Ajouter Limite: Ce paramètre contrôle la quantité de données envoyées à App par jour. Cela permet à la caméra pour ne pas dépasser la limite de plan de données d'un opérateur cellulaire.
PARAMèTRES DU CELLULAIRE (suite.) ! APN: Le Nom du point (APN) est le nom de votre appareil photo doit mettre en place une connexion à la passerelle entre le réseau cellulaire de votre opérateur et de l'Internet public. Ce paramètre est normalement automaticallty déterminée pendant l'assistant d'installation. S'il vous plaît consulter votre opérateur avant de modifier manuellement ce paramètre.
CARTE MÉMOIRE INSTALLATION Pour insérer la carte mémoire SD dans l'appareil: localisez la fente de la carte SD sur le côté droit du boîtier de l'appareil photo. Ensuite, avec l'étiquette de la carte SD orientée vers l'avant de l'appareil photo, insérez la carte SD.
FOMATAGE DE LA CARTE SD Il est toujours mieux de formater vos cartes SD à partir de l'appareil actuel que vous utilisez, dans ce cas l'appareil photo. Ce qui permettra à l'appareil photo de formater la carte dans le mode approprié. 1. Insérez la carte SD dans l'appareil photo. 2. Mettez l'appareil photo. 3. Appuyez sur le bouton MENU. 4. Accédez à "Paramètres avancés". Appuyez sur ENTER. 5. Accédez à "Formater la carte".
INSTALLATION ET RETRAIT DE LA PILE Pour retirer les piles de l'appareil, ouvrez le boîtier et appuyez sur le bouton ÉJECTION situé dans le coin inférieur droit. Ce qui permettra de glisser et de retirer le Compartiment à piles. De nouvelles piles, alcalines ou au lithium, de type 'AA' doivent être insérées en respectant l'orientation indiquée sur le compartiment.
DÉFINITIONS REFLEX (Sensibilité avancée à faible luminosité) -‐ Vitesse de déclenchement ultra-‐rapide. Ne manquez jamais un moment crucial. MATRIX(Technologie de réduction du flou) – Avancée réduction du flou réduit considérablement les effets de flou résultant en plus nettes, des images plus claires.
FOIRE AUX QUESTIONS Q: Qu'est-‐ce que la vitesse de déclenchement devrait être sur mon appareil furtif? A: Cela varie en fonction du modèle de la caméra. La plupart des modèles 2014/2015 sont approximativement moins de 1 seconde, une vitesse plus âgés modèle de déclenchement sont environ 2-‐3 secondes. Q: Puis-‐je utiliser des piles rechargeables dans mon appareil photo? A: Les piles rechargeables ne sont pas recommandées.
FOIRE AUX QUESTIONS (SUITE) Q: Puis-‐je échanger des cartes SD d'une caméra de reconnaissance à l'autre? A: Non, nous ne recommandons pas échangeant des cartes SD entre les différentes caméras. Chaque caméra est faite avec des capacités différentes de mise en forme et peut causer la caméra de ne pas reconnaître la carte SD.
CONFORMITÉ FCC GSM STC-GXATW Remarque : Cet équipement a été testé et se conforme aux exigences des appareils numériques de classe B, conformément à la partie 15 des Règles FCC. Ces limites sont conçues pour fournir une protection raisonnable contre les interférences nuisibles présentes dans une installation résidentielle.
RENSEIGNEMENTS SUR LA GARANTIE LIMITÉE Votre appareil photo d'exploration Stealth Cam est couverte par une garantie limitée de 365 jours sur les pièces et la main-‐d'œuvre à partir de la date d'achat initial, et les achats doivent être effectués auprès d'un revendeur autorisé. La garantie couvre les défauts de fabrication et les matériaux.