Reversible Plate Compactor 61012 Owner’s Manual Questions? Problems? Please call our customer support: (909) 628 4900 Mon-Fri 9am to 3pm PST WARNING To reduce the risk of injury, all operators and maintenance personnel must read and understand these instructions before operating，changing accessories，or performing maintenance about this power equipment. All possible situations cannot be covered in these instructions ． Care must be exercised by everyone using，maintaining or working near this equipment.
CONTENTS INTRODUCTION Introduction………………………………………………………2 Applications………………………………………………………2 Structure …………………………………………………………2 Functions and controls …………………………………… ……3 Accessories………………………………………………………3 For safety operation ……………………………………………3 Hazards and risks……………………………………………… 4 Operation………………………………………………………4-9 Care and preventive maintenance……………………………9 Service………………………………………………………… 9 Specifications…………………………………………………10 Spare parts and service………………………………………10 Replacement parts list …………………………………… 10-15
Power Transfer Air-cooled Single cylinder Engine is amounted as power source and Centrifugal Clutch is fixed on engine output shaft．Petrol Engine(2 cycle，4 cycle)and Diesel Gasoline Engine can be mounted as option．Centrifugal Clutch engages by running up the engine and engine R.P.M.
HAZARDS AND RISKS ENSURE that the fuel tank cap is securely fitted after refueling． NEVER allow any person to operate the machine without adequate instruction． ! CHEMICAL HAZARDS ENSURE all operators read ， understand and follow the operating instructions． DO NOT operate or refuel a petrol or diesel motor in a confined area without adequate ventilation． SERIOUS INJURY could result from improper or careless use of this machine CARBON MONOXIDE exhaust gases from internal combustion motor driven units c
Start the motor using the recoil starter．(If the motor is fitted with an on/off switch this must first be turned to ON before starting.) For more information on starting and correct operating procedures of the motor,refer to the motor operation manual sup- plied with the unit． Increase the motor speed to the maximum setting using the hand throttle lever,before commencing compacting． The machine should be controlled by grasping the handle with both hands and applying restraint to control the forward motion.
2-4．Stop engine without fail before replenishing fuel tank.
! CAUTION Do not pull the rope all the way and do not take your hand off the pulled knob but slowly return it original position． 3-8．After starting up the engine，be sure to perform a warm up the engine，be sure to perform a warm up run for 2 to 3 minutes．This should be performed without fail,particularly during winter season． 4.
6．Shutdown To stop the engine in an emergency，turn the stop switch to the OFF position． Under normal conditions, use the following procedure： 6-1．Set the speed control lever at the low speed position and allow the engine to run at low speed for 2 or 3 minutes before stopping． 6-2．Tum the stop switch to the OFF position．Fig-12 6-3．Close the fuel cock． Fig-13 7.
B.Remove spark plug，clean and adjust the spark plug gap to 0.6-0.7mm (0.02-0.03 in.). Fig-15 C.drain the motor oil of the engine and replace with new specified oil． Fig-16 ! NOTE：When the engine is new，the first oil change must be made after 20 hours of operation and replenish the oil tank before operating． 7-3. Monthly Service Change the oil in the vibrator assembly． 7-4. Storage When storing the compactor for long periods after operation． A.
! CAUTION ! CAUTION Inspection and other services should always be carried out on hard and level ground with the engine shutdown． Fuel piping and connections should be replaced every 2 years. TABLE2. ENGINE CHECK Inspection and Maintenance Service Tables． 1． To make sure your plate compactor is always in good working condition before using，carry out the maintenance inspection in accordance with Tables 1 through 3． ITEM TABLE1.
SPECIFICATIONS Model 61012 Engine Air-cooled, 4-cycle, single cylinder Engine type Petrol, Loncin 200F Power kw(hp) 4.7(6.5) Weight kg(lbs) 180(287) Frequency vpm 4600 Centrifugal Force kn 22 Compaction Depth cm(in) 50(19) Travel Speed cm/s(in/s) 20(8) Efficiency m2/hr (ft2/hr) 450(4844) Plate Size cm(in) 66X38(26x15) Dimension cm(in) 82X44.5X100(32X17.
REPLACEMENT PARTS LIST Major components and vibrator assembly parts list as followings.
·Major components list ITEM N0． PART N0． DESCRIPTl0N QUANTITY 1 300001 Hexagonal bolt M8x25 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 300002 300003 300004 300005 300006 300007 300008 300009 300010 300011 300012 300013 300014 300015 300016 300017 300018 Washer，lock M8 Washer，plat M8 Clutch assembly V-belt Engine Nut M10 Washer，lock M10 Washer，plat M10 Guard hook Throttle lever Grip Handle Shock absorber 1 1 1 1 1 4 4 4 1 1 1 1 2 4 2 2 2 19 20 21 300019 300020 300021 Hexagonal bolt M12x65 Vi
·Major components list 14
ITEM NO． 1 PART NO． 300001 DESCRIPTION Belt cover(blow) QUANTITY 1 2 300002 Screw M8x25 1 3 300003 Washer,lock M8 1 4 300004 Washer,plat 8.5x32x2.
50 51 300050 300051 Spring Bearing 16008 1 2 52 300052 Plug，oi1 M12x1．25x10 2 16
