Model: TLS-210S TV Mount Installation Guide Thank you for choosing Stanley – the hardware of choice for Architects, Contractors, and Home Owners for its quality, performance and dependability. Enclosed are your step-by-step instructions for an install made easy. If you get stuck, give customer service a call at 1-855-816-6868 You can also reach us at contact@stanleymounts.com www.stanleymounts.
! Caution: Please read the entire manual before proceeding View warranty and disclaimer on page 14 Getting Started Before we start lets make sure we have the correct mount and all the required tools and hardware to complete the installation. The TV is a Flat Panel TV is between 40” - 65” and weighs no more than 100lbs. The Wall the TV will be mounted on is either concrete or dry wall with wood studs.
! Caution: This product contains small items that could be a choking hazard if swallowed. Parts & Hardware ! Caution: Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact Customer Service.
Step 1: Attach Rails to TV 1 Check what screws (C,D,E,F), and flat washers (K,L) will fit in your TV.
2 Align the rails onto the back of the TV and install with the hardware.
Step 2A: Install Wall Plate on Drywall with Wood Stud Note: For Concrete skip to Step 2B 1 Use the stud finder to locate 2 studs. Then draw a vertical line on the center of each stud. 1 2 2 Level the wall plate and align it with the center of the studs. Make 2 Pencil marks to indicate where to drill. Tools Required: Pencil Level Stud Finder ! 6 Caution: The minimum size of the woodstud must be 1/2”x 3 1/2” and the thickness of the drywall must not exceed 5/8”.
3 Remove the wall plate and drill the pilot holes with a 3/16” drill bit 3 4 4 Align the wall plate with the pilot holes and insert 2 bolts through the washer in the pilot holes and tighten.
Step 2B: Install Wall Plate on Concrete 1 Level the wall plate and make 2 marks with pencil to show where to drill the pilot holes. 1 2 2 Remove the wall plate and drill the pilot holes with a 3/8” drill bit. Tools Required: Pencil 8 Level 3/8” Drill Bit Drill ! Caution: The minimum depth of the concrete must be 8”. Do not drill pilot holes into the mortar between the concrete.
3 Insert the anchors into the 2 pilot holes. Tap with a hammer 3 4 4 Align the wall plate with the pilot holes and anchors and insert 2 bolts through the washer into the anchors and tighten.
Step 3: Hang Your TV ! 1 To hang your TV, clip the TV Rails to the mounted wall plate. Warning: Always use 2 people to lift your TV. 1 2 “snap” “click” 2 After the TV is hanging properly on the wall mount, press on the bottom of the TV to lock it in place.
3 Pull the release cords down while gently pulling the bottom of the TV from the wall. 3 5 4 Install the cables.
Usage: Magnet Tabs 1 Take the magnet tabs hanging from the TV Mount and hang them on the metal frame of the TV Mount.
SUNCRAFT SOLUTIONS INC. LIMITED WARRANTY SUNCRAFT SOLUTIONS INC. LIMITED WARRANTY SUNCRAFT SOLUTIONS, INC. warrants its products to be free of defects in material and for a particular purpose and warranties of merchantability. SUNCRAFT SOLUTIONS, INC. will not workmanship for the product’s Warranty Period.
GENERAL DISCLAIMER General Disclaimer Disclaimer – Suncraft Solutions Inc. has extended every effort to ensure to accuracy and is damaged or missing. In the event that replacement parts or hardware are needed, please contact completeness of this manual. However, Suncraft Solutions Inc. does not claim that the information Customer Service at 1-855-816-6868 or service@suncraftsolutions.com . International customers covers all installation, situational or operational variables.