Gas Pressure Washer Owner’s Manual This Manual Contains Important Safety Instructions and Operating Instructions Models: P2350S, P2750S, P2350S-CAN, P2750S-CAN Contents: Page 2 Page 3 Page 4 Page 5 Page 6 Page 8 Page11 Page 15 Page 16 Page 17 Page 18 Page 19 Factory Original Parts Package Contents/Component Identification Wheel Kit Assembly and Product Specifications Missing Parts Request Form Warnings Preparation & Assembly Operation Maintenance Transporting and Storage Tips for Cleaning Troubleshooting L
FACTORY ORIGINAL STANLEY PARTS STANLEY is the Official Sponsor of NASCAR Racing ORDER ONLINE www.PressureWasher911.com Phone orders, call [1] 919-550-3259 Please have the part number and credit card ready when calling. Replacement Gun Part Number: SP02610 Price: $35.99 High Pressure Replacement Variable Adjustable Wand Part Number: SP02710 (Model: (P2350S, P2750S, P2350S-CAN, P2750S-CAN) Price: $39.
Package Contents/Component Identification A E C B G H I P D J F K Q R M L N O PARTS LIST for Model P2350S, P2750S, P2350S-CAN, P2750S-CAN Part Letter Number of Pieces Replacement Part Number A Part Name Gun Assembly 1 SP02610 B C D High Pressure variable adjustable wand Recoil Assembly 25’ High Pressure Hose (P2350S, P2750S, P2350S-CAN, P2750S-CAN) 1 1 1 SP02710 SP02810 SP02910 E F G Lifting Handles Pressure Washer Feet and Bolts Muffler 4 1 SP03010 SG00110 SP03110 H I Oil Fill Ca
Wheel Kit Assembly Step 1: Insert the handle and attach using tools provided in the hardware bag. Step 2: If you previously installed the 2 feet on the back of the pressure washer, remove the 2 feet from the back of the pressure washer frame with the wrench provided in the hardware bag. Wheel kit sold separately or may be included in certain models only. Step 3: Attach the wheels to the back of the pressure washer underneath the handles. PRODUCT SPECIFICATIONS Model P2350S 2350 PSI 2.
Missing Parts Request Form Please indicate the part that you are missing: Name Hardware bag Other Address Date of purchase Model #: Phone Email Serial #: Comments: IMPORTANT: Please include your receipt. Without a receipt, your order will be delayed. You may also email us at: customerservice@gxioutdoorpower.com Fax: 1-919-550-3277 If emailing, please scan in your proof of purchase.
Warnings This owner’s manual is considered a permanent part of the product and should remain with the product if resold. The information and specifications included in this publication were in effect at the time of approval for printing. GXi Outdoor Power, LLC, reserves the right to discontinue or change specifications or design at any time without notice and without incurring any obligation whatever. No part of this publication may be reproduced without written permission.
Warnings WARNING WARNING Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go. Broken bones, fractures, bruises or sprains could result. ALWAYS point gun in safe direction and squeeze spray gun trigger, to release pressure and avoid kickback each time, before starting engine. Engage trigger lock when not in use. When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.
PREPARATION & ASSEMBLY Assembly Time: 5 minutes Tools Required: 17mm Adjustable Wrench, and 8mm / 10mm wrench Step 5 Attach High Pressure Hose to Gun as shown in Figure below. Fasten tightly with 17mm wrench to avoid leakage. Surface Preparation Before starting any cleaning task, it is important to inspect the area for objects which could create a hazard. Remove any objects from the work area which could be tripped over, such as toys or outdoor furniture.
PREPARATION & ASSEMBLY DANGER Recommendation on oil change. Pressure Washer Clearance Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire. Keep at least 5 ft. (152 cm) clearance on all sides of pressure washer including overhead. Place pressure washer in a well ventilated area, which will allow for removal of deadly exhaust gas. DO NOT place pressure washer where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building.
PREPARATION & ASSEMBLY HOW TO USE THE PRESSURE WASHER WARNING If you have any problems operating your pressure washer, please call the pressure washer help-line at [1] 919-550-3259. A running engine gives off carbon monoxide, an odorless, colorless, poison gas. WARNING Pressure Washer Clearance Prevailing winds and air currents should be taken into consideration when positioning pressure washer. Keep spray nozzle between 8 to 24 inches away from cleaning surface.
OPERATION Step 1: Step 5 Make sure that the ON/OFF switch is in the “OFF” position. Release trigger and start the pressure washer by turning ON/OFF switch to ON. Step 2: Turn ON the water supply. Important: Never turn the engine on without having the water turned on. Running the pump with no water can cause pre-mature pump damage. Step 6 Pull the recoil to start. To start easier, hold the trigger on the gun to allow the water to flow.
OPERATION A B C D E Select the desired high pressure spray angle by using the high pressure adjustable wand. To scour surfaces, adjust wand to D or E angle. For gentle rinse, adjust wand to B or C angle. To apply chemical, adjust to low pressure as shown in angle A (for instructions on adjusting the wand to low pressure, see step 1 on page 13.
OPERATION WORKING WITH DETERGENTS Step 3 Working with detergent ensures a quick soaking of the dirt, and allows the high-pressure water to penetrate and remove the dirt more effectively. Always spray detergent on a dry surface. Do not pre-soak area with plain water. Wetting the surface first dilutes the detergent and reduces its cleaning ability. To siphon and apply detergent, you must operate the pressure washer on low pressure— adjust the nozzle to low pressure (see below for instructions.
OPERATION SHUTTING DOWN AND CLEANING UP Step 4 Disconnect the garden hose from the water inlet on the unit. Step 1 1. Let engine idle for two minutes. Turn the switch to “OFF” (0) position and unplug cord from outlet. Step 5 Disconnect the high-pressure hose from the high pressure outlet and engage the gun safety lock. Step 2 Turn off the water supply. Step 3 ALWAYS point gun in a safe direction and then press trigger to release water pressure for 20~30 seconds.
MAINTENANCE Connections Connections on pressure washer hoses, gun and spray wand should be cleaned regularly and lubricated with non-water soluble grease. Adjustable Nozzle Maintenance WARNING Surging, or pulsing sensation, felt while squeezing the spray gun trigger may be caused by excessive pump pressure. The principal cause of excessive pump pressure is a nozzle clogged or restricted with foreign materials, such as dirt, etc.
TRANSPORTING AND STORAGE Winterizing and Long Term Storage CAUTION You must protect your unit from freezing temperatures. Failure to do so will permanently damage your pump and render your unit inoperable. Freeze damage is not covered under warranty. STORAGE TIME Recommended Service Procedure to prevent hard starting: 1 to 2 months Fill with fresh gasoline and add fuel stabilizer 2 months to 1 year Fill with fresh gasoline and add fuel stabilizer.
TIPS FOR CLEANING CAUTION Before cleaning any surface, an inconspicuous area should be cleaned to test spray pattern and distance for maximum cleaning results. If painted surfaces are peeling or chipping, use extreme caution as pressure washer may remove the loose paint from the surface. When using on surfaces which might come in contact with food, flush surfaces with plenty of drinking water. Automobiles, RV’s, Boats, Motorcycles, ATV’s Pre-rinse vehicle with fresh water.
TROUBLESHOOTING Symptom Output pressure varies high and low, no pressure, sudden loss of pressure, low water volume. Cause Not enough inlet water supply. Solution Turn water on full force. Check garden hose for kinks, leaks or blockage. Pump is sucking air. Check that hoses and fittings are air tight. Turn off machine. Purge pump by squeezing trigger gun until a steady flow of water emerges through the nozzle. Discharge nozzle is obstructed. Blow out or remove debris with a fine needle.
LIMITED WARRANTY LENGTH OF WARRANTY:* (FROM THE DATE OF ORIGINAL RETAIL PURCHASE) PRODUCTS COVERED BY THIS WARRANTY: NONCOMMERCIAL/ NONRENTAL COMMERCIAL RENTAL Engine 24 months 6 months 3 months Pump 12 months 6 months 6 months Wands, hoses, detergent bottles, quick connects, accessories 3 months 3 months 3 months Emission Controls 24 months 24 months 24 months *LENGTH OF WARRANTY: All warranty coverage except emission controls expires when the product exceeds 24 months.
