Brochure

Bulletin 30-10 / Page 19
for Air, Water, Steam and Light Oil Industrial Solenoid Valves
EPYT
DRADNATS
SNOITCENNOC
sehcnI
TROP
EZIS
sehcnI
DPOM
isp
MGARHPAID
SSELNIATS
LEETS
TAESTRESNI
SGNITARLIOC
CA CD
DRADNATS
SELCYC/STLOV
STTAW
LIOC
CA CD
1P3W elameFTPN4/1 901.
051
001
—
oN
06-05/42
06-05/021
06-05/042-802
06-05/042-802-021lauD
01 51 1-CKM
1P6W elameFTPN8/3 61/3
521 seY
2P41W elameFTPN2/1 61/7
51 81 2-CKM
2P91W elameFTPN4/3 23/91
2P52W elameFTPN1 23/52
1P381R
elameFTPN8/3
61/9
051 06
nolfeT
oN
06-05/42
06-05/021
06-05/042-802
06-05/042-802-021lauD
01 51 1-CKM
1P381RB N-anuB
1P381RK nolfeT
seY
1P381RBK N-anuB
1P481R
elameFTPN2/1
nolfeT
oN
1P481RB N-anuB
1P481RK nolfeT
seY
1P481RBK N-anuB
1P642R
elameFTPN4/3 4/3
nolfeT
oN
1P642RB N-anuB
1P642RK nolfeT
seY
1P642RBK N-anuB
Type R184P1
Diaphragm Type
Type W3P1
Direct Acting Type
Diaphragm Type
Disc Type
n
Maximum rated pressure: Type W3P1 and Diaphragm Types, 300 psi; All others - 500 psi
n
Dual voltage 4-wire coils, 120-208-240/50-60 are available at slight additional cost. For
other voltages and cycles, consult Sporlan, Washington, MO 63090.
n
Body - Brass
n
Available with conduit boss or junction box at no extra charge.
n
5 psi minimum operating pressure differential W6 thru W25.
Application
These valves are suitable for most types of industrial
applications. Ideal for water, glycol, most refrigerant
oils and heat transfer fluids, air lines to chucking
devices, steam lines, etc. Use the disc type valves
for high temperature and steam applications up to
25 psia. Use the teflon diaphragm type valve for
high temperature and steam applications over 5 psig
(225°F) but do not exceed 10 psig (240°F). For appli-
cations above 240°F, consult Sporlan, Washington,
MO. These valves may be mounted horizon-
tally, on their side or in a vertical line.
Direct Acting Type
The W3P1 is the ideal size for use on air chucking
devices. Generally a very tight seat is required for this
type of application. This can be achieved by using a
neoprene seat in the W3P1 in place of the standard
teflon. To order specify RW3P1.
Disc Type
In certain areas of the country, particularly hard water
localities, the integral brass seats in solenoid valves
may deteriorate very rapidly. This problem is solved
by using a stainless steel seat insert in the brass body
in place of the usual brass seat. Valves from the W6
series through the W25 series have this feature. These
valves are also equipped with teflon seating materials
for long life. The W14 series through the W25 series
are also equipped with a closing spring on top of the
disc to assist in valve closing.
Diaphragm Type
These valves are tight seating in applications of normal
differential pressure. For applications where differen-
tial pressures in the closed position are below 5 psi,
it is recommended that a Buna-N diaphragm be used
in place of the standard teflon diaphragm. To order
specify BR184P1 or KBR184P1.
In certain areas of the country, particularly hard water
localities, the integral brass seats in solenoid valves
may deteriorate very rapidly. This problem is solved
by using a stainless steel seat insert in place of the
usual brass seat. Example: KR184P1.
Nomenclature - Diaphragm Type
K B R 81 4 P 1
Stainless Steel
Insert Seat
Buna-N
Diaphragm
Series
Port Size 1/32”
Connection
Size 1/8”
Pipe
Connections
MKC-1 Coil
Specifications — Reverse Refrigeration Flow, Liquid Line Capacity (Tons)**