Air Die Grinder Model: 07630 *Actual product may vary slightly 88007630 02/2014
Important Operating Instructions CALIFORNIA PROPOSITION 65 WARNING: You can create dust when you cut, sand, drill or grind materials such as wood, paint, metal, concrete, cement, or other masonry. This dust often contains chemicals known to cause cancer, birth defects, or other reproductive harm. Wear protective gear. WARNING: This product or its power cord may contain chemicals, including lead, known to the State of California to cause cancer and birth defects or other reproductive harm.
Important Operating Instructions GENERAL SAFETY INSTRUCTIONS • Keep the work area clean and well lit. Cluttered and dark areas increase the risk of electric shock, fire, and injury to persons. • Do not operate the tool in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. The tool is able to create sparks resulting in the ignition of the dust or fumes. • Keep bystanders, children, and visitors away while operating the tool.
Important Operating Instructions GENERAL SAFETY INSTRUCTIONS • Risk of electric shock. This tool is not provided with an insulated gripping surface. Contact with a “live” wire will also make exposed metal parts of the tool “live” and shock the operator. • Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock. • Examine the work piece to avoid contact with hidden wiring.
Important Operating Instructions GENERAL SAFETY INSTRUCTIONS • Tool service must be performed only by qualified repair personnel. • When servicing a tool, use only identical replacement parts. Use only authorized parts. • Use only the lubricants supplied with the tool or specified by the manufacturer. • Never connect to an air source that is capable of exceeding 200 PSI. Over pressurizing the tool may cause bursting, abnormal operation, breakage of the tool, or serious injury.
Important Operating Instructions VIBRATION PRECAUTIONS This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms, and shoulders. To reduce the risk of vibration-related injury: 1. Anyone using vibrating tools regularly or for an extended period of time should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use.
Important Operating Instructions controls the air supply even if the air hose is ruptured. The shut-off valve should be a ball valve because it can be closed quickly. Note: if an automatic oiler system is not used, add a few drops of pneumatic tool oil to the airline connection before operation. Add a few more drops after each hour of continual use. 2. Attach an air hose to the compressor’s air outlet. Connect the air hose to the air inlet of the tool.
Important Operating Instructions WARNING: Read the ENTIRE important operating instructions before set-up or use of this product. Inspect tool before use, looking for damaged, loose, and missing parts. If any problems are found, do not use the tool until it has been repaired. WORK AREA SET-UP 1. Designate a work area that is clean and well-lit. The work area must not allow access by children or pets to prevent distraction and injury. 2.
Important Operating Instructions Prior to use, the Die Grinder requires the attachment of a Quick Connector into the air inlet. To do so, wrap approximately 3 inches of pipe thread sealer tape (not included) around the male threads of a Quick Connector. Then, firmly tighten the Quick Connector into the Air Inlet. OPERATING INSTRUCTIONS WARNING: Always wear ANSI approved safety glasses, a full face shield, and hearing protection when operating the Die Grinder. 1.
Important Operating Instructions 7. Once the work is completed, release hand pressure on the Trigger. The Safety will automatically return to its locked position to prevent the Trigger from accidentally being activated (see Figure 2). 8. Turn off the air compressor. Trip the Safety with your finger, and slowly squeeze the Trigger to release any remaining air pressure from the Die Grinder. Then, disconnect the air hose from the tool. 9. Remove the Grinding Drum from the Die Grinder.
Important Operating Instructions 2. Daily: With a clean cloth, remove all dirt, oil, and grease from the Die Grinder. If necessary, you may use a mild detergent. Do not use solvents, as damage to the Die Grinder may occur. Do not immerse the Die Grinder in any liquids.
Description Air Hose Filter Regulator Lubricator (Optional) Coupler and Plug Leader Hose (Optional) Air Cleaner/Dryer (Optional) Air Adjusting Valve (Optional) # A B C D E F G H Fine tuning airflow at tool Prevents water vapor from damaging work piece Increases coupler life Provides quick connection and release Air tool lubrication Adjusts air pressure on tool Prevents dirt and condensation from damaging tool or work piece Connects air source to tool Function Air Supply Set-up
Important Operating Instructions WARRANTY Limited Manufacturer Warranty North American Tool Industries (NATI) makes every effort to ensure that this product meets high quality and durability standards. NATI warrants to the original retail consumer a 1-year limited warranty from the date the product was purchased at retail and each product is free from defects in materials.
PARTS LIST Air Die Grinder Model: 07630 14 88007630 02/2014
PARTS LIST Model: 07630 Air Die Grinder # Description # Description 1 Housing 21 Front End Plate 2 Throttle Lever 22 Ball Bearing 3 Roll Pin 23 Pin 4 Valve 24 Bevel Gear 5 Valve Spring 25 Connect Nut 6 Valve Plug 26 Clamp Nut 7 Air Regulator 27 Angle Head 8 Valve Bushing 28 Ball Bearing 9 O-Ring 29 Bevel Gear 10 O-Ring 30 Woodruff Key 11 O-Ring 31 Work Spindle 12 O-Ring 32 Lock Nut 13 Ball Bearing 14 Rear End Plate 15 Rotor 34 Collet Jacket 16 Ro
