Instructions / Assembly

For quick and easy installation of your folding door,
read these instructions thoroughly. A few minutes
of prior planning will make the job easier and will
ensure years of trouble-free use.
The Tools You Will Need
• Small #1 Phillips type screwdriver • tape measure
• small nail • 3/32” drill bit for pilot holes • hacksaw
or ne tooth saw (saw needed to trim top track for
the appropriate width or to trim height of panels if
opening is less than 80” high) • masking tape (to
secure doors if trimming is necessary)
• Safety glasses.
SINGLE DOOR INSTALLATION
1. Measure the Door Opening
If the height of your door
opening is approximately
80”, you will not need to
alter the door itself. If the
opening is less than 80”
high, the door may be
shortened by sawing o
excess from the
bottom of the door
panels (end without holes).
If the opening is less than
80” high: Stack the door
panels together, secure
with masking tape and
cut with a hacksaw or ne
tooth saw. Cut the overhead track 1/8” shorter
than the width of the opening.
Remove the masking tape.
The width of the door cannot be altered.
7. Secure The Anchor Panel
Slide the entire door
against the non-opening
side of the doorway.
With the door panel
hanging naturally, locate
the holes on the anchor
panel where the door will
be secured to the jamb.
Using the drill, insert the
screws and secure the
end anchor panel
to the jamb.
8. Install Magnetic Latch Striker Plate
Place the magnetic latch striker plate against
the magnet on the lead edge. Close the door
until it strikes the door jamb. Mark the top and
bottom location of the striker plate on the jamb.
Align the striker plate on the marked
location and secure to the jamb with two
athead screws.
VIA/REGENT 36”x80”
INSTALLATION INSTRUCTIONS
Double Door Installation
Via doors can be used as a Double door but due to the
magnets, there will be approximately a 0.25” gap when the
doors are in the closed position.
1. Measure the Door Opening
Divide the width of the opening by two. Cut each top track
to this measurement so that when installed, the tracks butt
against one another in the center of the door opening.
2. Install One Top Track
On a center line drawn across the top of the door opening,
install either half track and install all screws in the half track.
3. Install the Handles
Tap the two handle attachment pins into one handle, then
t the pins through the door panel holes. Press the other
handle onto the pins. Repeat with the other handle.
4. Install the Top Glides
Position one top glide over the center hole in the top
of a full width door panel and snap into place until
secure. Repeat with remaining top glides.
To secure the T-style lead edge top glide, place the T shaped
part inside the lead edge and align the holes. Then insert
the female section from the outside hole through the hole in
the T shaped glide through the other side of the lead edge.
Then insert the threaded male screw into the female part
and tighten until snug. Repeat with the other door.
5. Install Second Track and Door Panels
Apply track lubricant to each top glide. Install the two doors
in the half track with lead edges facing each other. Then
install the second track and push one door onto this track.
Set a screw at the track center joint and leave the screw
projecting down 1/2” to prevent glides from passing
the joint.
6. Secure Anchor Panels
Slide one door against the door jamb. With the door panel
hanging naturally, locate the holes on the anchor panel
where the door will be secured to the jamb. Using the drill,
insert the screws and secure the end anchor panel to the
jamb. Repeat with the other door.
To close the doors, pull together until magnets latch.
Secure in
the Channel
Align
Striker
Plate
Closure
Channel
80”
Closure
Channel
96”
Make Sure All
The Following
Parts Are
Included With
Your Folding
Door:
Anchor Screws
Tornillos de jación
Top Track
Guía superior
Striker Plate
Placa de encastre
Handle
Manija
Lead Edge
Borde delantero de la puerta
Top Glides
Patines superiores
Anchor Panel
Panel de jación
T-Style Top Guide
Patín superior en forma de T
Magnet
Magnética
Door Parts Location
Handle
Handle
1 Overhead Track
2 Handles Pins
12 Track & Anchor
Screws
2 Flathead
Screws
1 Magnetic
Latch Striker
Plate
Female & Male
Connectors
1 T-Style
Top Glide
7 Top
Glides
4. Install The Top Glides
Position one top glide
over the center hole in
the top of a full width
door panel and snap
into place until secure.
Repeat with remaining
top glides.
To secure the T-style
lead edge top glide, place the T shaped part
inside the lead edge and align the holes. Then
insert the female section from the outside hole
through the hole in the T shaped glide through
the other
side of
the lead
edge. Then
insert the
threaded
male screw
into the
female part
and tighten
until snug.
5. Install the Door Panels
Apply track lubricant to each top glide. Swing
one end of the top track out of the door opening
to accept the top glides. Decide if you want the
door to open from the left or the right, then slide
all top glides onto the track. Stack the panels
together near the center screw.
6. Secure The Top Track
Swing the track back to its original position.
After making pilot
holes (with a nail or a
3/32”drill bit), drive the
track screws through
all track holes. Set all
screws as straight and
tight as possible to
ensure smooth
operation of the door.
2. Install the Top Track
Position the top track
on the top of the
door opening so that
it is straight and
centered. After
making a pilot hole
(with a nail or 3/32”
drill bit), drive a track
screw through the
screw hole nearest the center of the track. Do
not tighten. (Tape may be used to hold the track
in place while you mark and drill.)
3. Install the Handles
Tap the two handle
attachment pins into one
handle, then t the pins
through the door panel
holes. Press the other
handle onto the pins.
If necessary, you may back one handle with a
solid object and tap the other handle alternately
over each pin area until the handles are seated.
Do not strike the middle of either handle.
1 Tube
of Track
Lubricant
Installation pdfs, videos, warranty registration and
replacement parts can be found on our website under the
Product Support section.
125 Route 61 • Schuylkill Haven, PA 17972
1.800.360.1585 • fax [phone]
www.ltlhomeproducts.com • e-mail: [e-mail]