Specifications

ManualsBrandsSpacepro ManualsFitted wardrobesSliding Doors and track Arctic White Glass + Storage

HOW TO INSTALL YOUR STANDARD

SIZED SLIDING DOORS

Read carefully through these instructions before you start

PLEASE READ before starting assembly. Carefully open the packs supplied and check the contents against the parts

and ﬁttings check list. Do Not dispose of the packaging until you are certain that you have all the necessary parts for the

assembly. The manufacturer reserves the right to alter speciﬁcations without prior notice.

IMPORTANT NOTES:

1. Please ensure that the packaging is disposed of in a safe environmentally friendly way.

2. There are small components used in the construction of the door frame. These loose items should be kept away from

young children whilst assembling.

3. Protect the high ﬁnish of the tracks by using a suitable material on the working surface during assembly.

4. We recommend that two people carry out this assembly.

5. Make sure there are no pipes or cables where you are drilling.

You will also need: Pozidrive screwdriver, Hacksaw,

Tape measure, Bradawl, Spirit level, Electric drill, Drill

bits and suitable wall plugs.

Identify and, if necessary, construct the correct opening width for your doors using the table below and

instructions A to E shown on the back page.

All Doors are made to ﬁt a standard opening height of 2260mm. A higher ceiling can be reduced using Spacer Blocks

or Opening Height Reducers as shown in section E on the back page.

STANDARD SIZED SLIDING DOORS

Fitting Standard Door Instructions

UK_STD_HD06.14

B Bottom Track *

A Top Track *

Sliding Door

(either Mirror or

panel) complete

with all framing

& hardware

Sizing the Tracks

Measure the width of the top of your opening. Using a

set square mark a straight line across the Top Track A.

Measure the width of the base of your opening. Mark a

corresponding line across the Floor Track B. Cut

the tracks using a ﬁne tooth hacksaw

Installing the Doors

Always locate the back

door/s ﬁrst. Angle the door

and insert the top of the

door into the top track.

Straighten the door and

lower the bottom wheels

into the Floor Track grooves.

Engaging the Top Guide

(Not Applicable to Twin pack doors)

Push up white plastic

section of the guide to

engage into top track. To

remove door from top track

pull down on top guide as

shown. The guide will then

disengage from top track.

Lift out at an angle.

Adjusting the Doors

Align the doors so the end

doors are plumb to the side

walls. Adjust the bottom

wheels using a pozidrive

screwdriver, altering the height

and angle of each door. Turn

the screw clockwise to raise

the door and anti-clockwise to

lower the door.

Engaging Anti-jump Clips

Clips must be engaged to ensure doors do not

leave tracks.

Installing the Tracks

Top Track - Position the Track into the top of the

opening. Mark where holes need to be drilled in the track

(we recommend a ﬁxing at each end and centre then at

approx 500mm intervals in between). Drill and plug the

header/ceiling in line with the holes drilled in the track and

ﬁx the top track using the long screws provided (see back

page for suggestions).

Floor Track - Position the track on the ﬂoor of the opening. Mark

where holes need to be drilled in the track (we recommend a ﬁxing

at each end and centre then at regular intervals in between). Before

permanently ﬁtting the ﬂoor track to your ﬂoor, ﬁt the door into place

and using a spirit level adjust the Floor Track so the door becomes

vertical.

Positioning the Doors

(Not Applicable to Twin pack doors)

Position your doors in the appropriate combinations

shown below, to allow for overlapping.

1 4

Normally a minimum

of 610mm, if used as

wardrobe doors

32mm

Back Wall

Normally a minimum

of 610mm, if used as

wardrobe doors

32mm

Back Wall

Normally a minimum

of 610mm, if used as

wardrobe doors

32mm

Back Wall

Normally a minimum

of 610mm, if used as

wardrobe doors

32mm

Back Wall

Normally a

minimum of

593mm if

used as a

wardrobe

Xmm

2 Doors

3 Doors

4 Doors

To disengage anti-jump clip just reverse procedure.

Note: In the unlikely event of anti-jump clip becoming detached

during engagement, simply snap it back into original position

shown on drawing A.

A Rotate

anti-jump clip

into open position

B Push

anti-jump clip fully

down into track

C Rotate

anti-jump clip back

into closed position

We provide these components with your Wardrobe

Doors and Track-Set. Components marked with * are

supplied in the Track-Set. The Top Guides and Bottom

Wheels are pre-ﬁtted to the Wardrobe Doors.

www.hdhc.com

Width of opening

Twin pack

trackset only (1200mm)

Summary of content (2 pages)

PAGE 1
STANDARD SIZED SLIDING DOORS www.hdhc.com HOW TO INSTALL YOUR STANDARD SIZED SLIDING DOORS Sizing the Tracks Measure the width of the top of your opening. Using a set square mark a straight line across the Top Track A. A the width of the base of your opening. Mark a Measure corresponding Bline across the Floor Track B. Cut the tracks using a fine tooth hacksaw 1 Read carefully through these instructions before you start PLEASE READ before starting assembly.
PAGE 2
STANDARD SIZED SLIDING DOORS www.hdhc.com HOW TO CONSTRUCT YOUR OPENING WIDTH A Fitting to the wall B Fitting Wall to side fillet Opening width (Selected from table) The use of end fillets is recommended to allow the doors to slide flush where an existing skirting board is fitted. Remove a section of the skirting and fit an end fillet. To reduce your opening width from between 127 - 457mm / 5 -18” on each side you can use Opening Reducers fixed to the side wall.