Instructions / Assembly

ManualsBrandsSouthwire ManualsDusk-To-Dawn Flood Lights4800-Lumen 240-Watt EQ Bronze Halogen Dusk-to-Dawn Floodlight

INFARED MOTION

ACTIVATED SECURITY LIGHT

INSTALLTION INSTURCTIONS

Model # L6003

1 Year Warranty on Fixture

(Does not apply to bulbs, which have no warranty)

Congratulations and Thank You! The fixture you have purchased should give you 1

year of trouble free service. We take pride in the design and construction of each of our

products and work to maintain the quality of our materials and craftsmanship to assure

your satisfaction.

This product is warranted to be free of defects in workmanship and materials for a period

of 1 year from the original date of purchase. If any problems appear (other than burnt

out bulbs, which carry no warranty) within 1 year, the purchaser may return the item,

freight prepaid, together with a copy of your original purchase receipt to:

Southwire Co. 11290 80

Ave. Pleasant Prairie, WI 53158

Upon receipt of the item prepaid with a letter describing the problem, and a check for

$7.50 to cover return postage and handling, the company will, at its option, either repair

or replace the defective part or fixture at no charge to the purchaser. This warranty does

Summary of content (7 pages)

PAGE 1
INFARED MOTION ACTIVATED SECURITY LIGHT INSTALLTION INSTURCTIONS Model # L6003 1 Year Warranty on Fixture (Does not apply to bulbs, which have no warranty) Congratulations and Thank You! The fixture you have purchased should give you 1 year of trouble free service. We take pride in the design and construction of each of our products and work to maintain the quality of our materials and craftsmanship to assure your satisfaction.
PAGE 2
not apply to fixtures that have been used for rental or commercial purposes. It does not cover fixtures that have been altered in any way or fixtures that have been subject to misuse, accidents or damage in transit. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES. NO CHARGES WILL BE ACCEPTABLE FOR UNAUTHORIZED REPAIRS, PARTS OR SERVICE.
PAGE 3
Note: The detection range specified above is based on the sensor’s performance in conditions that represent average temperatures found in North America. The detection range of the sensor will vary with changing ambient temperatures. This fixture may be mounted on a wall or an eave. It may be mounted onto a standard recessed outlet box or a wet location / outdoor outlet box. For easy installation, replace an existing light fixture that is already connected to a wall switch. WARNING: Maintain minimum 1.
PAGE 4
electrical shock. MAIN CIRCUIT BREAKER OR FUSE WIRING THE LIGHT CONTROL Fixture is pre-wired for quick and easy installation for both professionals and do-it-yourself alike: DO NOT REMOVE ANY CRIPMP CONNECTORS PREINSTALLED!! ONLY WHITE, BLACK AND GREEN WIRES WILL NEED TO BE ATTACHED TO INCOMING LINES!! 1. Check local electrical codes before installation. Use only 120 Volt 60hz power supply. 2. Be sure power is turned off at breaker or fuse box.
PAGE 5
8. Wiring portion is now complete, so you can install bulbs. Again, double check wall switch is in off position and power is shut off at breaker. OPERATION Test Mode Activate the photocell and allow the motion detector to function in daylight for time setting. Auto Mode Turn knob from 30 seconds to 10 minutes as needed. Manual Override Mode Turn the wall switch Off-On twice within 2 seconds, the lights will come on and stay on. After 6 hours, this option will automatically return to Auto Mode.
PAGE 6
SPECIFICATIONS Sensor Range Up to 70 ft.(21m) Sensing Angle 180 degree + Downward detection Power Consumption 4 watts maximum(control module only) Power Requirement 110/120 volts 60 Hz Load Rating 500 watts maximum (Incandescent only) Operating Modes TEST, AUTO, MANUAL, and Temperary ON Mode Delay Control 30 seconds to 10 minutes (approximately) LED Indicator 1 piece LED for Test Mode indicator & intruder watcher TROUBLESHOOTING Lights do not come on at all: 1.
PAGE 7
4. Aim motion detector head lower, away from moving busy areas such as sidewalks and streets. Motion Detector comes on randomly, or blinks in test mode. 1. Move floodlights away from motion detector head, or use lower wattage lamps. 2. Aim motion detector head lower. 3. Make sure motion detector head is not aimed at heating/cooling ducts, metal sheds, pools of water, windows, or smooth walls. 4. Adjust Range sensitivity setting. 5.