Music Mixer User Manual

ManualsBrandsSony ManualsMusic MixerSRP-V110

 1998 by Sony Sound Tec Corporation

2-346-297-21 (1)

Table of Contents

AUDIO MIXER

SRP-V110

Main characteristics...............................2

Dimensions..............................................2

Connections example............................3

Name and function of each part...........4

MONO INPUT section..............................4

STEREO INPUT section.............................6

MONITOR section...................................8

MASTER section.....................................9

Back panel section.................................!º

Operating instructions

Before operating the unit, please read this manual and the supplied

“WARNING” thoroughly and retain it for future reference.

Precautions

On safety (Refer to the supplied “WARNING”.)

•Should any liquid or solid object fall into the cabinet, unplug the unit and

have it checked by qualified personnel before operating it any further.

•Unplug the unit from the wall outlet if it is not to be used for an extended

period of time. To disconnect the cord, pull it out by grasping the plug.

Never pull the cord itself.

On installation

•Do not install the unit in a location near heat sources such as radiators or

air ducts, or in a place subject to direct sunlight, excessive dust,

mechanical vibration or shock.

On operation

•Before making program source connections, be sure to turn the power

switch off and unplug the unit.

•When the unit is not used, turn the power off to conserve energy and to

extend the useful life of your unit.

On cleaning the cabinet

Clean the cabinet, panel and controls with a soft cloth lightly moistened

with mild detergent solution. Do not use any type of abrasive pad, scouring

powder or solvent such as alcohol or benzine.

On repacking

Do not throw away the carton and the packing material. It makes an ideal

container for transporting the unit.

When shipping the unit for repair work or to another location, repack it as it

was.

If you have any questions or problems concerning your unit, please contact

your nearest Sony dealer.

Block diagram.........................................!™

Main specifications................................!£

Trouble-shooting guide.........................!¢

To prevent fire or shock hazard, do not

expose the unit to rain or moisture.

To avoid electrical shock, do not open

the cabinet. Refer servicing to qualified

personnel only.

This symbol is intended to alert the user to the

presence of uninsulated "dangerous voltage"

within the product's enclosure that may be of

sufficient magnitude to constitute a risk of

electric shock to persons.

This symbol is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

*The caution marking is put on the bottom enclosure.

Summary of content (16 pages)

PAGE 1
2-346-297-21 (1) AUDIO MIXER SRP-V110 Operating instructions Table of Contents Main characteristics ............................... Dimensions .............................................. 2 2 Connections example ............................ Name and function of each part ........... MONO INPUT section .............................. STEREO INPUT section ............................. MONITOR section ................................... MASTER section .....................................
PAGE 2
Main characteristics This is a small, multi-functional eight-group buses audio mixer combined with a small/mid-sized SR system and multi track recorder, etc. that supports recording systems. Equipped with 10 channels of mono input, 4 channels of stereo input, and 4 channels of auxiliary stereo input Equipped with 8 AUX channels AUX 1/2 can be used as STEREO AUX of the pre-fader. AUX 3/4 can (simultaneously) switch between the pre and post faders. AUX5/6 can be switched to AUX7/8 using the fader.
PAGE 3
Connections example SR system connection Main characteristics Dimensions Keyboard Compressor AUDIO MIXER SRP-V110 Microphone CD or MD Player Compressor Connections example Graphic Equalizer Graphic Equalizer Effector Power Amplifier Power Amplifier Main Speaker Monitor Speaker Recording system connection Keyboard Multi Track Recorder Compressor Microphone CD or MD Player AUDIO MIXER SRP-V110 Monitor Speaker Effector DAT(Master Recorder) 3
PAGE 4
Name and function of each part MONO INPUT section 1 POWER switch When the switch is pressed to the ON side, the power is turned on. 2 LEVEL control ON 1 POWER OFF 1 2 LEVEL TAPE 2 LCF +10 -10 5 6 TAPE LEVEL LCF +10 -10 -40 -60 LEVEL -40 -60 +10 -10 HIGH 3 4 HIGH -15 +15 -15 +15 -15 500 1.5K 500 1.
PAGE 5
9 AUX 1-2 PAN control When turned towards the “1”, sound is shifted to the AUX 1 bus, and when turned in the “2” direction, it is shifted to the AUX 2 bus. When turned to the maximum in either direction, the output level is increased by +3 dB. !º AUX 1-2 control This controls the level that is sent to the AUX 1/2 buses. This AUX is a pre-fader (splitting the signal before the channel fader).
PAGE 6
Name and function of each part STEREO INPUT section ST5 ST6 ST7 ST8 !∞ -∞ 2 0 -∞ 0 -∞ ST2 ST3 ST4 -10dBs -10dBs -10dBs -15 +15 -15 +15 -15 +15 HIGH -15 +15 -15 +15 -15 +15 MID 4 LOW 5 0 -∞ 0 -∞ 0 -∞ 0 0 -∞ 0 -∞ 0 -∞ 0 L-R 0 -5 1-2 3-4 5-6 -10 --∞ 0 -∞ 0 0 -∞ 0 -5 3-4 5-6 -10 7-8 LOW AUX 1-2 0 3 -∞ 0 -∞ 0 -∞ 0 4 57 57 8 68 68 -∞ 0 0 ON ON PFL PFL L R ODD EVEN PEAK +10 1-2 +15 4 L-R +5 -15 MID 3 PEAK +10 +15 -∞ L R
PAGE 7
ST1 - ST4 channels 1 –10 dBs button When this button is turned off, the reference input level is +4 dBu; and when it is turned on, it is –10 dBu. 2 HIGH (High equalizer) level control This varies the high equalizer level between –15 - +15 dB. The equalizer is a 12 kHz shelving type. 3 MID (Mid equalizer) level control 4 LOW (Low equalizer) level control This varies the low equalizer level between –15 - +15 dB. The equalizer is a 40 Hz peaking type.
PAGE 8
Name and function of each part MONITOR section 1 PHONES (headphones) connector Phone jack (Tip: L, Ring: R, Sleeve: GND) This is the connector that the headphones are connected to. The same signals are output as those from the MONITOR OUTPUT connectors, and signals from channels whose PFL or AFL buttons are turned on can be confirmed. 2 PEAK meter indicator AUDIO MIXER SRP-V110 1 This is lit up when the level meter is used as a peak meter.
PAGE 9
MASTER section 1 AUX MASTER controls This controls the output level to the AUX OUTPUT connector. 2 PRE buttons This switches AUX 3 and AUX 4 for all channels between the pre-fader and post fader. It is switched to pre-fader when it is on, and post fader when it is off.
PAGE 10
Name and function of each part Back panel section 74 5 STEREO INPUT ST5 ST2 ST6 R L L(MONO) R GRP/ DIRECT OUT ST1 L(MONO) R TAPE IN MONO INPUT 8 7 L(MONO) INSERT LINE INSERT LINE MIC ON OFF !£ !º 8 R +48V MONITOR OUT R ST8 L ST7 L(MONO) R L ST4 R 10 ST3 R L(MONO) L(MONO) MIC R OUTPUT INSERT R R L 8 L L OUT 7 6 5 4 3 IN R 2TR MASTER !™ 1 MONO INPUT MIC connectors XLR-3-31 type (Balanced, reference level: –60 - –10 dBu) (Pin No.1: ground, No.2: hot, No.
PAGE 11
3 2 GRP/ DIRECT OUT MONO INPUT 7 INSERT TAPE IN MONO INPUT 2 MIC 1 LINE INSERT LINE INSERT LINE INSERT LINE 1 MIC INSERT LINE INSERT LINE INSERT LINE MIC 2 9 INSERT 4 MIC 3 LINE 3 MIC MIC 6 2 5 1 5 MIC MIC 6 1 Name and function of each part 4 74 8 AUX OUTPUT connectors Phone jacks (Unbalanced, reference level: +4 dBu) 9 2TR OUT connectors Phono jacks (Unbalanced, reference level: –10 dBu) These distribute and output the MASTER OUTPUT L/ R signals.
PAGE 12
AUX 5-8 PFL L PFL R CONTROL GP OUT1-8 L-R GROUP 1-8 AUX 1-2 AUX 3-4PRE AUX 3-4POST Block diagram +48V FADER PEAK TAPE MIC -10 - -60dBs L-R ON LCF FADER 1-2 INSERT LCF LINE +10 - -40dBs -20dB STEREO L OUTPUT +4dBs PAN EQ 3-4 FREQ LEVEL 5-6 LEVEL 7-8 LOW MID HIGH INSERT MONI STEREO R OUTPUT +4dBs PAN TAPE INPUT -10dBs INSERT AUX1-2 AUX3 AFL ATT GROUP/DIRECT OUTPUT -10dBs ATT AUX4 DIRECT 2TR OUTPUT -10dBs ATT AFL MONO 7/8 LEVEL METER AUX5/7 7/8 PEAK AUX6/8 L/ODD PFL PHONES
PAGE 13
Main specifications Name MONO INPUT Connector type Circuit Reference level Maximum level Impedance Suitable load impedance MIC XLR-3-31 type Balanced –60 - –10 dBu –37 - +13 dBu 2.2 kΩ — LINE ø 6.3 Phone jack –40 - +10 dBu –17 - +27 dBu 22 kΩ — TAPE INPUT Phono jack Unbalanced –10 dBu +13 dBu 10 kΩ — INSERT INPUT ø 6.3 Phone jack Unbalanced –3 dBu +20 dBu 30 kΩ — –3 dBu +20 dBu 47 Ω 600 Ω or more INSERT OUTPUT STEREO INPUT ø 6.
PAGE 14
Trouble-shooting guide In the event of any unexpected problems, please double-check the following points. If after that, normal operation cannot be resumed, contact the store from which the item was purchased, or your nearest Sony dealer. Condition Causes/Solutions When the POWER switch is turned on, the power indicator does not light up, nor is any sound output. • Check that the power cord is connected. Although the POWER indicator is lit, no sound is output.
PAGE 15
PAGE 16
Printed in Japan