Owner / Operator’s Manual This Manual Must Be Read Before Operating The Equipment SP-85 Serial No. PD-102588 and higher SP-85SS Serial No. PE-100800 and higher CUSTOMER COPY Madison Heights, Michigan 48071 800-SALTERS www.snowexproducts.
Table of Contents General Information....................................................................................................................................................................................... 3 Introduction .................................................................................................................................................................................................. 4 Safety ........................................................................
General Information CONGRATULATIONS! The spreader you have purchased is an example of snow and ice control technology at its finest! Your spreader’s self-contained design is a trademark of all SnowEx products. Here’s why… SIMPLICITY: Fewer moving parts manufactured of higher quality means minimal maintenance for your SnowEx spreader. RELIABILITY: High impact linear low density polyethelyne hopper. Custom engineered, powder coated frame. And a custom engineered transmission found only on Snowex products.
Introduction This manual has been designed for your help. It will assist you and instruct you on the proper set-up, installation and use of this spreader. Refer to the table of contents for an outline of this manual. We require that you read and understand the contents of this manual completely (especially all safety information) before attempting any procedure contained herein.
Safety Before attempting any procedure in this book, these safety instructions must be read and understood by all workers who have any part in the preparation or use of this equipment. For your safety warning and information decals have been placed on this product to remind the operator of safety precautions . If anything happens to mark or destroy the decals, please request new ones from TurfEx. Remember, most accidents are preventable and caused by human error.
Assembly Instructions Model # SP-85 / SP-85SS Step 1: Slide Actuator Rod up through the slot in the Spreader Support Leg from the spinner side. Step 2: A: Attach Actuator Rod to Gate Linkage. Secure with Hair Pin Clip. B: Remove Pivot Bolt that attaches the Gate Linkage to Frame.
Assembly Instructions Model # SP-85 / SP-85SS Step 3: A: Attach Actuator Rod to Handle. B: Slide Handle Assembly onto Spreader Frame and install corresponding Hardware from provided Hardware Kit. C: Reinstall Pivot Bolt that was removed in Step 2B. See Deflector Assembly Parts Breakdown p. 16 Step 5: Put Weather Cover on Hopper.
Operating the Spreader Model # SP-85 / SP-85SS SPREADER LOADING Capacity: 2 Cubic Ft Hopper WARNING – Do not overload spreader. Weights of material are an average for dry materials. Material Weight Per Cubic Ft. Bulk Salt 80-90 lbs. • Warning – Never remove spreader from vehicle with material in it as this could cause damage to the frame assembly. • Warning – Never leave materials in hopper for long periods of time, salt is hygroscopic and will attract atmospheric moisture and harden up.
Maintenance Model # SP-85 / SP-85SS Important Gears and Axles Must Be Lubricated and Greased Every 20 Hours of Use. Remove Gear Housing and apply Chain Lube Spray Lubrication. Use General Purpose Grease on both Grease Zerks.
Troubleshooting Model # SP-85 / SP-85SS TOO MUCH MATERIAL FLOW GATE STUCK OPEN LUBRICATE GATE SLIDES DROP SPREADER: ADJUST FRONT GATE SLIDE ADJUST GATE STOP LUBRICATE LINKAGE REMOVE AND CLEAN IF BROKEN, REPLACE CABLE STUCK LUBRICATE REPLACE RECONNECT ACTUATOR / LINKAGE NOT ENOUGH MATERIAL FLOW POOR SPREAD PATTERN 10 HANDLE DOES NOT WORK ADJUST/REPLACE HARDWARE / HANDLE PHYSICAL OBSTRUCTION REMOVE GATE STUCK CLOSED (SEE ABOVE) AGITATOR IN PLACE NO: REPLACE EMPTY HOPPER FILL WITH MATERI
Warranty Model # SP-85 / SP-85SS Limited Warranty SnowEx products are warranted for a period of two years from the date of purchase against defects in material or workmanship under normal use and service, subject to limitations detailed below. Warranty period of two years begins on the date of purchase by the original retail user. The WARRANTY REGISTRATION must be submitted to the SnowEx for this warranty to become effective. This warranty applies to the original retail purchaser only.
Spreader Views Model # SP-85 / SP-85SS PE-100000 12 © Trynex International 2013 (REV A) F50768
Spreader Views Model # SP-85 / SP-85SS © Trynex International 2013 (REV A) F50768 13
Hopper Assembly Parts Breakdown Model # SP-85 / SP-85SS 16 2 15 17 6 9 14 13 3 18 1 4 10 5 13 11 12 18 7 14 14 8 © Trynex International 2013 (REV A) F50768
Hopper Assembly Parts Breakdown Model # SP-85 / SP-85SS ID # 1 2 3 4 5 6 7 Part # D5900 D5903 D5905 D5912 D5914 D5920 D5927 © Trynex International 2013 (REV A) F50768 Qty 1 1 4 1 1 1 1 ID # 8 9 10 11 12 13 14 Part # D5928 D5933 D5934 D5935 D5936 D5937 D5948 Qty ID # 1 15 16 17 18 1 1 1 Part # D5953 D6041 T15014 T15016 Qty 3 1 2 3 1 3 7 15
Deflector Assembly Parts Breakdown Model # SP-85 / SP-85SS 3 2 8 7 11 6 9 7 1 4 5 10 3 16 © Trynex International 2013 (REV A) F50768
Deflector Assembly Parts Breakdown Model # SP-85 / SP-85SS ID # 1 2 3 4 5 6 © Trynex International 2013 (REV A) F50768 Part # D5209 D5931 D5932 D5940 D5949 D5951 Qty 6 1 2 6 6 3 ID # 7 8 9 10 11 Part # D5952 D5953 T15016 T15018 T15023 Qty 6 3 3 4 3 17
Axle Assembly Parts Breakdown Model # SP-85 19 2 16 1 14 9 6 5 15 4 13 14 20 17 11 10 18 21 12 7 8 18 3 © Trynex International 2013 (REV A) F50768
Axle Assembly Parts Breakdown Model # SP-85 ID # 1 2 3 4 5 6 7 8 9 10 11 © Trynex International 2013 (REV A) F50768 Part # D5901 D5902 D5904 D5909 D5910 D5911 D5913 D5915 D5956 D5919 D5921 Qty ID # 1 12 13 14 15 16 17 18 19 1 2 1 1 2 1 1 1 1 20 21 Part # D5923 D5926 D5930 D5938 D5939 D5941 D5947 D5993 D5994 D6024 Qty 4 1 3 1 1 1 1 1 2 2 2 19
Handle Assembly Parts Breakdown Model # SP-85 4 12 10 3 7 8 6 14 13 5 2 9 11 13 1 20 © Trynex International 2013 (REV A) F50768
Handle Assembly Parts Breakdown Model # SP-85 ID # 1 2 3 4 5 6 7 8 © Trynex International 2013 (REV A) F50768 Part # D5906 D5907 D5908 D5917 D5918 D5924 D5925 D5929 Qty 1 2 1 2 1 1 ID # 9 10 11 12 13 14 Part # D5943 D5944 D5945 D5946 T15016 T15018 Qty 4 2 1 1 8 1 1 1 21
Axle Assembly Parts Breakdown Model # SP-85SS 18 1 15 21 13 8 7 4 14 3 12 13 19 16 10 9 22 20 11 6 7 17 2 © Trynex International 2013 (REV A) F50768
Axle Assembly Parts Breakdown Model # SP-85SS ID # 1 2 3 4 5 6 7 8 9 10 11 © Trynex International 2013 (REV A) F50768 Part # D5902 D5904 D5909 D5910 D5911 D5913 D5915 D5956 D5919 D5921 D5923 Qty ID # 1 12 13 14 15 16 17 18 19 2 1 1 2 1 1 1 1 2 4 20 21 Part # D5926 D5930 D5938 D5939 D5941 D5947 D5993 D5994 D6024 T30151 Qty 1 3 1 1 1 1 1 2 2 1 23
Handle Assembly Parts Breakdown Model # SP-85SS 2 10 8 14 5 6 4 12 11 3 1 7 9 11 13 24 © Trynex International 2013 (REV A) F50768
Handle Assembly Parts Breakdown Model # SP-85SS ID # 1 2 3 4 5 6 7 8 © Trynex International 2013 (REV A) F50768 Part # D5907 D5917 D5918 D5924 D5925 D5929 D5943 D5944 Qty 2 2 1 1 1 1 ID # 9 10 11 12 13 14 Part # D5945 D5946 T15016 T15018 T30152 T50153 Qty 1 1 8 1 1 1 4 2 25
Notes 26 © Trynex International 2013 (REV A) F50768
Notes © Trynex International 2013 (REV A) F50768 27
131204
