INSTRUCTION MANUAL INDUCTION COOKTOPS SAI95
SAI95
SUMMARY SAFETY ......................................................................................................................................... 4 PRECAUTIONS BEFORE USING........................................................................................................ 4 USING THE APPLIANCE .................................................................................................................. 4 PRÉCAUTIONS NOT TO DAMAGE THE APPLIANCE .................................................
SAFETY Precautions before using • Unpack all the materials. • The installation and connecting of the appliance must be done by a qualified electrican. The manufacturer can not be responsible for damage caused by building-in or connecting errors. • The appliance must be installed in a proper worktop. • This domestic appliance is exclusively for the cooking of food, to the exclusion of any other domestic, commercial or industrial use. • Remove all labels and self-adhesives from the ceramic glass.
• In general do not place any metallic object except cooking pots on the glass surface. • Never cover the appliance with a cloth or a protection sheet. This may become very hot and catch fire. • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
• Never put any flammable object (eg. sprays) into the drawer situated under the vitroceramic hob. Cutlery drawers must be resistant to heat. Precautions in case of appliance failure • If a defect is noticed, switch off the appliance and turn off the electrical supply. • If the ceramic glass is cracked or fissured, you must disconnect the appliance at the switchboard and contact the after sales service. • Repairing has to be done by specialists. Do not open the appliance by yourself.
DESCRIPTION OF THE APPLIANCE Technical characteristics Type SAI95 Total Power 11100 W Position of the heating zone Diameter Left Ø180/260 mm Middle Right Ø180 mm 2x220x180 mm Nominal Power* 1st Booster Power* 2nd Booster Power* 1850/ 3700 W 1850 W 2050 W 2300/ 4500 W 2300 W 2900 W 3000/ 5500 W 3000 W 3700 W Minimum diameter detection 90/220 mm 100 mm 100 mm * The given power may change according to the dimensions and material of the pan.
USE OF THE APPLIANCE Display Display 0 1…9 U A E H P L U II Designation Zero Power level No pan detection Heat accelerator Error message Residual heat 1st Booster 2nd Booster Locking Keep warm Description The heating zone is activated. Selection of the cooking level. No pan or inadequate pan. Automatic cooking. Electronic failure. The heating zone is hot. The 1st Booster is activated. The 2nd Booster is activated. Control panel locking. Maintain automatically at approximately 42. 70. 94°C.
Power selection zone “SLIDER” and timer setting zone To select the power with the slider, slide your finger on the “SLIDER” zone. You can already have a direct access if you put your finger directly on the chosen level.
Residual heat indication After the switching off of a heating zone or the complete stop of the hob, the heating zones are still hot and indicates [ H ] on the display. The symbol [ H ] disappears when the heating zones may be touched safely. As long as the residual heat indicators are on, don’t touch the heating zones and don’t put any heat sensitive object on them. There are risks of burn and fire.
• To stop the cooking time: Action Control panel Display Select the Timer Press simultaneously key [ - ] and [ + ] Timer display on from the timer until the desired display is on Stop the time Press key [ - ] from the timer [ 000 ] If several timers are activated, repeat the process. • Egg timer function: Egg timer is an independent function. It stops as soon as a heating zone starts up. If the egg timer is on and the hob is switched off, the timer continues until time runs out.
Recall Function After switching off the hob ( ), it is possible to recall the last settings. • cooking stages of all cooking zones (Booster) • minutes and seconds of programmed cooking zone-related timers • Keep warm function • Automatic cooking The recall procedure is following: • Press the key [ ] • Then press pause key before the light stops blinking. The previous settings are again active.
COOKING ADVICES Pan quality Adapted materials: steel, enamelled steel, cast iron, ferromagnetic stainless-steel, aluminium with ferromagnetic bottom. Not adapted materials: aluminium and stainless-steel without ferromagnetic bottom, cupper, brass, glass, ceramic, porcelain. The manufacturers specify if their products are compatible induction. To check if pans are compatibles: • Put a little water in a pan placed on an induction heating zone set at level [ 9 ].This water must heat in a few seconds.
Examples of cooking power setting (the values below are indicative) 1 to 2 Melting Reheating 2 to 3 Simmering Defrosting 3 to 4 Steam 4 to 5 Water 6 to 7 7 to 8 9 P and Sauces, butter, chocolate, gelatine Dishes prepared beforehand Rice, pudding, sugar syrup Dried vegetables, fish, frozen products Vegetables, fish, meat Steamed potatoes, soups, pasta, fresh vegetables Meat, lever, eggs, sausages Goulash, roulade, tripe Potatoes, fritters, wafers Steaks, omelettes, fried dishes Water scallops, steaks Boilin
The control panel displays [ E ]: • • • The electronic system is defective. Disconnect and replug the hob. Call after sales One or all cooking zone cut-off: • • • • • The safety system functioned. You forgot to cut-off the cooking zone for a long time. One or more sensitive keys are covered. The pan is empty and its bottom overheated.
INSTALLATION INSTRUCTIONS The installation must be performed by a qualified electrical contractor. How to stick the gasket: The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. His installation has to be done carefully, in conformity of the following drawing. Stick the gasket (2) two millimeters from the external edge of the glass, after removing the protection sheet (3).
ELECTRICAL CONNECTION • • • • • • • The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously. Protection against the parts under tension must be ensured after the building-in. The data of connection necessary are on the stickers place on the hob casing near the connection box.
Connection of the hob The ceramic hob can be connected in different ways: Monophase 230V~1P+N Biphase 400V~2P+N Triphase 400V~3P+N Setting up the configurations: For the various kinds of connection, use the brass bridges which are in the box next the terminal Monophase 230V~1P+N Put the 1st bridge between terminal 1 and 2 and between 2 and 3, the 2nd between 4 and 5. Attach the earth to the terminal “earth”, the neutral N to terminal 4 or 5, the Phase L to one of the terminals 1, 2 or 3.
Warranty THIS WARRANTY IS VALID IN AUSTRALIA ONLY Note: Please complete the following details when you have unpacked the product and retain this card with the purchase invoice or sales docket. Warranty: This product is covered by a Warranty in addition to all rights available to you by statute. Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
Smeg Australia Pty Ltd Sydney Head Office 02 8667 4888 Smeg Service 02 8667 4833 Smeg Spare Parts 02 8667 4875 Smeg Melbourne 03 9094 1999 Australia-wide distributors: Newcastle 02 4960 9266 Wagga Wagga 02 6922 8600 Queensland 07 3266 0444 Tasmania 03 6334 8166 South Australia 08 8346 1888 Western Australia 08 9389 8000 www.smeg.com.au Smeg Australia Pty Ltd is constantly seeking ways to improve the specifications, design and production of its products.
