LBS86-1 LBS106-1 Washing Machine Lavatrice
Safety instructions 1 Warnings General Safety • Never place your machine on a carpet covered floor. Otherwise, lack of airflow from below of your machine may cause electrical parts to overheat. This may cause problems with your washing machine. • If the power cable or mains plug is damaged you must call Authorized Service for repair. • Fit the drain hose into the discharge housing securely to prevent any water leakage and to allow machine to take in and discharge water as required.
2 Installation Removing packaging reinforcement Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon. Opening the transportation locks A Transportation safety bolts must be removed before operating the washing machine! Otherwise, the machine will be damaged! 1. Loosen all the bolts with a spanner until they rotate freely (“C”) 2. Remove transportation safety bolts by turning them gently. 3.
Electrical connection Connect the machine to an earthed outlet protected by a fuse of suitable capacity. Important: • Connection should comply with national regulations. • The voltage and the allowed fuse protection are specified in the section “Technical Specifications”. • The specified voltage must be equal to your mains voltage. • Connection via extension cords or multiplugs should not be made. B A damaged power cable must be replaced by a qualified electrician.
4 Selecting a Program and Operating Your Machine Control panel 6 1 4 2 123456- Spin Speed Adjustment Knob * Time Delay Button * Temperature Adjustment Knob * Start/Pause/Cancel Button Auxiliary Function Keys Program Selection Knob Select the appropriate program from the program table and the following washing temperature table according to type, amount and degree of soiling of the laundry. Select the desired program with the program selection button.
shorter washing cycle is used compared to the “Cottons” program. It is recommended for your synthetic clothes (such as shirts, blouses, synthetic/cotton blended garments, etc.). For curtains and lace, the “Synthetic 40” program with pre-wash and anti-creasing functions selected is recommended. •Delicates You can wash your delicate clothes on this program. It has more sensitive washing movements and does not make intermediate spinning compared to “Synthetic” program.
Max. Load (kg) Programme Duration (~min) Water Consumption (l) Energy Consumption (kWh) Prewash Quick Wash Rinse Plus Anti-Creasing Rinse Hold Spin speed reduction No Spin Program selection and consumption table Cottons 90 6 150 55 2.00 • • • • • • • Cottons 60** 6 140 49 1.14 • • • • • • • Cottons 40 6 125 49 0.70 • • • • • • • Intensive 60 6 160 65 1.30 • • • Synthetics 60 3 115 55 0.90 • • • • • • • Synthetics 40 3 105 55 0.
at the minimum rpm given on the panel. No spin You may use this program if you do not want to spin your clothes at the end of cottons, synthetics, woolen or delicate programs. Auxiliary functions Auxiliary function selection keys Select the required auxiliary functions before starting the program. C Auxiliary function buttons may differ according to the model of your machine.
5 Maintenance and cleaning program. Select the “Cottons 40” program. Start the program. Detergent Drawer Switching the machine to standby mode Remove any powder residue buildup in the drawer. To do this; 1. Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine. Press “Start/Pause/Cancel” button momentarily to switch your machine to the standby mode.
Draining any remaining water and cleaning the pump filter Your product is equipped with a filter system which ensures a cleaner water discharge that extends pump life by preventing solid items such as buttons, coins and fabric fibers from clogging the pump propeller during discharge of the washing water. • If your machine fails to drain the water, the pump filter may be clogged. You may have to clean it every 2 years or whenever it is plugged. Water must be drained off to clean the pump filter.
6 Solution suggestions for problems Problem Cause Machine may have to self Program cannot switched protection mode due to be started or an infrastructure problem selected. (such as line voltage, water pressure, etc.). Explanation / Suggestion Reset your machine by pressing “Start/Pause/ Cancel” button for 3 seconds. (see, Canceling a Program) There is water coming from the bottom of the machine. There might be problems with hoses or the pump filter.
7 Specifications Models LBS86-1 LBS106-1 Maximum dry laundry capacity (kg) 6 6 Height (cm) 84 84 Width (cm) 60 60 Depth (cm) 54 54 Net Weight (kg) 71 71 Electricity (V/Hz.) 230 V / 50hz 230 V / 50hz Total Current (A) 10 10 Total Power (W) 2200 2200 Spinning cycle (rpm max.) 800 1000 Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly.
