Libretto di Istruzioni Manuel d’Instructions Instructions Manual Gebruiksaanwijzing Bedienungsanleitung Bruksanvisning Manual de instrucciones Manual de Instruções Руководство по эксплуатации KSE951X - KSE912X
RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. • The minimum safety distance between the cooker top and the extractor hood is 650 mm.
CHARACTERISTICS 433 90 max. 1055 132 650 min. 60 259 740 min. 740 Dimensions 300 260 490 108 150 Components Ref. 1 2 2.1 2.2 9 10 14.1 15 Q.ty Product Components 1 Hood Body, complete with: Controls, Light, Blower, Filters 1 Telescopic Chimney comprising: 1 Upper Section 1 Lower Section 1 Reducer Flange ø 150-120 mm 1 Damper 2 Air Outlet Connection Extension 1 Air Outlet Connection 15 14.1 12a 7.2.1 10 2.1 EN 12c 2 2.2 Ref. Q.ty Installation Components 7.2.
INSTALLATION 1÷2 Wall drilling and bracket fixing 116 116 650 min. 320 11 12a X 7.2.1 Wall marking: • Draw a vertical line on the supporting wall up to the ceiling, or as high as practical, at the centre of the area in which the hood will be installed. • Draw a horizontal line at 650 mm above the hob. Place bracket 7.2.1 on the wall as shown about 1-2 mm from the ceiling or upper limit aligning the centre (notch) with the vertical reference line.
Mounting the hood body • Before attaching the hood body, tighten the two screws Vr located on the hood body mounting points. • Hook the hood body onto the screws 12a. • Fully tighten support screws 12a. • Adjust screws Vr to level the hood body. Vr 12a Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a flexible or rigid pipe ø 150 or 120mm, the choice of which is left to the installer.
ELECTRICAL CONNECTION • Connect the hood to the mains through a two-pole switch having a contact gap of at least 3 mm. • Remove the grease filters (see paragraph Maintenance) being sure that the connector of the feeding cable is correctly inserted in the socket placed on the side of the fan. 7.2.1 Chimney assembly Upper exhaust Chimney • Slightly widen the two sides of the upper chimney and hook them behind the brackets 7.2.1, making sure that they are well seated.
USE Control board Key A B C D E F G H I L Function Switches the motor on and off at the latest selected speed Decreases the suction speed. Increases the suction speed. By pressing this key it is possible to start the intensive speed from any previously selected speed. This speed has been timed at 10 minutes. After that time the system activates automatically the latest selected speed.
MAINTENANCE Metal grease filters Filters can be washed in the dish machine. They need to be washed when FF-sign appears on the display or in any case every 2 months, or even more frequently in case of particularly intensive use of the hood. Alarm reset • Press the G-key for at least 2 seconds. Cleaning • Remove the filters one at a time holding them up with one hand and pulling the handle downwards with the other hand at the same time. • Wash the filters. Pay attention not to bend them.
Charcoal filter (recycling version) This filter cannot be washed or regenerated. It has to be replaced when the EF appears on the display or at least once every 4 months. Activation of the alarm signal • In the recycling version hoods the filter saturation alarm has to be activated during the installation or later. • Switch off the hood and the lights. • Press the E-key for about 5 seconds until the LED on the display start to move.