Libretto di Istruzioni (IT) Instruction booklet (EN) (AR) Mode d’emploi (FR) Bedienungsanleitung (DE) Instruktionsvejledning (DA) Manual de instrucciones (ES) Instrukcja (PL) Manual de lnstruções (PT) Instructiehandleiding (NL) Bruksanvisning (NO) Руководство по эксплуатации (RU) Instruktionshandbo (SE) Ohjekirja (FI)
WARNINGS! • • • • • • • • • • • • INSTALLATION Read the instructions closely before installing and/or using the hood. The manufacturer will not be held liable for damage caused by installation that is incorrect or not up to standard. We recommend that all installation and adjustment procedures are carried out by trained personnel. When the hood is taken out of its packaging inspect it to ensure that it is intact. If the product is damaged, do not use it and contact the Smeg assistance service.
the dangers it entails. • Children must be supervised to ensure that they do not play with the appliance • ATTENTION: The accessible parts can become very hot if they are used with cooking equipment. • • • • • MAINTENANCE Before carrying out any maintenance procedure or cleaning, disconnect the appliance from the electricity supply. Carry out thorough and timely maintenance of the filters in accordance with the intervals recommended by the manufacturer.
INSTALLATION INSTRUCTIONS: The hood is supplied with all the accessories necessary for its installation. The minimum distance between the lower surface of the hood and the hob must be at least 650mm for electric hobs (Fig. 1). If the motor inlet is equipped with a non-return valve for fumes, make sure it can open and close freely. For easy installation it is recommended to follow the procedures described below: 1) The hood must be centred with respect to the hob surface.
FILTER version: Leave the motor inlet free. Install the active carbon filters as shown on page 8. If the hood is not supplied with an active carbon filter you must buy it separately at your nearest authorised Smeg dealer. For some models there is a standard set of fittings (fig.6) to be fixed to the wall by expansion plugs at a suitable height in order to channel the airflow in correspondence with the flue slits. Insert laterally the extensions R2 on the fitting R1.
• USER INSTRUCTIONS CONTROLS UNIT For an optimal and efficient use of the product it is advisable to start the hood a few minutes before you start cooking and to keep it on for at least 15min after you have finished cooking or until steam and odours have completely disappeared.
2-DIGIT 10-KEY CAPACITIVE PUSHBUTTON BOARD: Key Function Display A Turns the suction motor on / off. Displays the set speed B Decreases the operation speed. Displays the set speed C Increases the operation speed. Displays the set speed Displays alternatively HI D Activates the Intensive speed from any speed even with the motor off, this speed is timed. At the end, the system returns to the speed previously set. Suitable for dealing with the maximum emissions of cooking fumes.
1-DIGIT CAPACITIVE PUSHBUTTON BOARD: KEY FUNCTION DISPLAY A SWITCH THE SUCTION MOTOR ON / OFF.
N.B. In some countries, the 4-speed version is also available, with the layout shown on the right, where: Filters Reset Key FUNCTIONS AND MAINTENANCE: Before performing any maintenance and/or cleaning always disconnect the hood from the power supply Regular cleaning guarantees good operation and a long appliance service life. The grease filters and filter hoods with carbon filters require special care. N.B.
In the case of the disc filter, simply tilt the two filters by 90° as shown in (fig.A) and then extract them from their housing. In the case of a cartridge filter attached with springs, (fig.B) exert the pressure required to counteract the resistance of the spring and then remove the filter In the case of a cartridge filter blocked with a bracket and threaded knob, (fig. C), unscrew the knob, remove the locking bracket and then remove the active carbon filter.
WEEE DISPOSAL: Pursuant to art. 26 of the Italian Legislative Decree dated 14 March 2014, no. 49 "Implementation of directive 2012/19/EU on Waste Electrical and Electronic Equipment (WEEE)" The crossed out wheeled bin symbol on the equipment or its packaging indicates that the product at the end of its useful life must be collected separately from other waste.
