DE NL UK FR SE IT ES PT Montage- und Gebrauchsanweisung Montagevoorschriften en gebruiksaanwijzingen Instruction on mounting and use Prescriptions de montage et mode d’emploi Monterings- och bruksanvisningar Istruzioni di montaggio e d'uso Montaje y modo de empleo Instruções para montagem e utilização
DE - Montage- und Gebrauchsanweisung Bitte nehmen Sie auch die Abbildungen auf den ersten Beiden Seiten mit den alphabetischen Bezeichnungen, die im Text wiedergegeben sind, zur Hilfe. Die Instruktionen, die in diesem Handbuch, gegeben werden, sind bitte ganz streng einzuhalten. Es wird keinerlei Haftung übernommen für mögliche Mängel, Schäden oder Brände der Küchenhaube, die auf die Nichtbeachtung der Vorschriften in diesem Handbuch zurückzuführen sind.
einer Schutzfolie ab und legen Sie die Dunstabzugshaube sowie alle im Lieferumfang enthaltenen Teile darauf.
Tragegestell; diese dienen auch dazu, die beiden Teile mittig auszurichten. 16. Die vier Schrauben, die die Haube am Tragegestell befestigen, festziehen. 17. Den elektrischen Anschluss des Bedienfeldes und der Lampen durchführen. 18.
auszuwählen, die Betriebszeit beträgt 5 Minuten (Taste blinkt), danach schaltet sich die Haube ab bzw. kehrt zur vorher ausgewählten Saugstärke zurück. Hinweis: Es besteht die Möglichkeit, diese Funktion so einzustellen, dass sich die Haube in jedem Fall nach 5 Minuten Betriebszeit ausschaltet (auch wenn vorher eine andere Saugstärke ausgewählt war).
Ersetzten der Lämpchen Wartung Das Gerat von Stromnetz abschalten. Hinweis: Vor Berühren der Lampen sich vergewissern, dass sie abgekühlt sind. Bild 4 1. Die Lampenabdeckung losschrauben. 2. Die defekte Lampe auswechseln. Ausschließlich Halogenlampen zu max. 20W (G4) verwenden und darauf achten, diese nicht mit den Händen zu berühren. 3. Die Lampenabdeckung wieder andrehen.
Es wird keinerlei Haftung übernommen für Fehler, Schäden oder Brände des Gerätes, die durch Nichteinhaltung der in diesem Handbuch aufgeführten Anweisungen verschuldet wurden. In Übereinstimmung mit den Anforderungen der Europäischen Richtlinie 2002/96/EG über Elektro- und Elektronik-Altgeräte (WEEE) ist vorliegendes Gerät mit einer Markierung versehen.
NL - Montagevoorschriften en gebruiksaanwiizing Raadpleeg ook de tekeningen uit de eerste bladzijden met de alfabetische verwijzingen uit de toelichtende tekst. Zich strikt aan de aanwijzingen uit deze tekst houden. Iedere aansprakelijkheid voor eventuele schade of brand aan het apparaat veroorzaakt door het niet in acht nemen van de aanwijzingen in deze handleiding weergegeven wordt afgewezen.
• Controleer tevens of er in de buurt van de installatie ruimte (op een, ook met gemonteerde kap, goed bereikbare plaats) een stopcontact aanwezig is en of er de mogelijkheid bestaat voor de verbinding aan een rookafvoer naar buiten (alleen voor het afzuigende apparaat). • Voer alle nodige werkzaamheden op de muur uit (bijv.: een elektriciteitsstopcontact en/of een doorvoeropening voor de afvoerpijp). De wasemkap is voorzien van bevestigingspluggen die geschikt zijn voor de meeste muurs/plafonds.
kap (doe de kap op zijn plaats). 19. Schakel de voedingsspanning vanuit het centrale schakelpaneel in en controleer of de wasemkap goed functioneert. Selecteer het kookvlak en kalibreer de sensoren (lees hiervoor de werkingsinstructies van het bedieningspaneel aandachtig door). andere uiteinde van de pijp aan de aansluitring aanwezig op de luchtgeleider F. 16. Maak de elektrische aansluiting. 17.
Beschrijving van de wasemkap afb. 1 1. Bedieningspaneel 2. Vetfilter 3. Handgreep voor ontgrendeling van het vetfilter 4. Halogeenlamp 5. Dampscherm 6. Telescopische schouw 7. Luchtuitgang (alleen voor gebruik als filterend apparaat) Werking 6. In geval van een sterkere dampconcentratie een hogere zuigkracht gebruiken. We raden aan de afzuigkap 5 minuten voordat men begint te koken aan te doen en deze nog voor ongeveer 15 minuten nadat men beëindigt heeft aan te laten.
Vervanging lampjes Onderhoud Sluit de stroom af. Attentie! Alvorens de lampjes aan te raken controleer eerst of ze koud zijn. afb. 4 1. Schroef de lampbescherming. 2. Vervang het kapotte lampje. Gebruik alleen halogeenlampjes van 20W max (G4), en zorg ervoor dat u hen niet met de blote hand aanraakt. 3. De lampbescherming weer op zijn plaats vastschroeven. Als de verlichting niet werkt, controleer dan of de lampjes goed op hun plaats zitten alvorens de assistentiedienst te bellen.
Iedere aansprakelijkheid voor eventuele schade aan het apparaat of brand veroorzaakt door het niet in acht nemen van de aanwijzingen uit deze handleiding wordt afgewezen. Dit apparaat is voorzien van het merkteken volgens de Europese richtlijn 2002/96/EG inzake Afgedankte elektrische en elektronische apparaten (AEEA).
UK - Instruction on mounting and use Consult the designs in the front pages referenced in the text by alphabet letters. Closely follow the instructions set out in this manual. All responsibility, for any eventual inconveniences, damages or fires caused by not complying with the instructions in this manual, is declined. Note: the elements marked with the symbol “(*)” are optional accessories supplied only with some models or elements to purchase, not supplied.
connect a fumes discharge device to the outside (only suction version). • Carry out all the masonry work necessary (e.g. installation of an electric socket and/or a hole for the passage of the discharge tube). Expansion wall plugs are provided to secure the hood to most types of walls/ceilings. However, a qualified technician must verify suitability of the materials in accordance with the type of wall/ceiling. The wall/ceiling must be strong enough to take the weight of the hood.
centre line printed on the drilling template must correspond to the centre line drawn on the wall, and the bottom edge of the drilling template must correspond to the bottom edge of the hood. 3. Place the lower support bracket on the perforation diagram making it coincide with the traced triangle, mark the two external holes and perforate. Remove the perforation diagram, insert two wall-dowels and fix the support bracket of the hood with two 5x45 mm screws. 4. Hang the hood onto the lower bracket. 5.
(blinking push-button) , following this the suction function will either turn off or return to the suctionspeed that had previously been selected. Note: It is possible to keep a check of this function so that the hood switches off 5 minutes after it has worked, (even though another function had been selected prior to this one) after having pressed the button, press again and keep pressed , the pilot-light will start blinking indicating that the selected function has been set.. 6.
will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. Replacing lamps Disconnect the hood from the electricity. Warning! Prior to touching the light bulbs ensure they are cooled down. Fig. 4 1. Unscrew the lamp cover. 2. Replace the damaged light bulb. Only use halogen bulbs of 20W max (G4), making sure you do not touch them with your hands. 3. Refit the lamp cover.
FR - Prescriptions de montage et mode d’emploi Consulter les dessins de la première page avec les références alphabétiques que l’on retrouvera dans le texte explicatif. Suivre strictement les instructions de cette notice. Le constructeur décline toute responsabilité pour tous les inconvénients, dommages ou incendies provoquès à l’appareil et dus à la non observation des instructions de la présente notice.
de la hotte (dans une zone également accessible avec la hotte déjà montée), il y a une prise électrique et qu’il est possible de se raccorder à un dispositif d’évacuation de fumées vers l’extérieur (uniquement Version aspirante). • Effectuer tous les travaux de maçonnerie nécessaires (par exemple: installation d’une prise électrique et/ou trou pour le passage des tubes d’évacuation). La hotte est équipée de chevilles de fixation convenant à la plupart des parois/plafonds.
18. Faire glisser la section inférieure de la cheminée pour couvrir totalement le groupe d’aspiration, jusqu’à ce qu’elle soit insérée dans son logement sur la hotte. Remonter le châssis du filtre à charbon et le/les filtre(s) à graisse et contrôler le fonctionnement parfait de la hotte. Installation du modèle pour mur Fig. 7 a. Poser le groupe d’aspiration sur un plan puis enfiler sur celui-ci la partie inférieure de la hotte. b. Effectuer les branchements électriques entre les deux parties. c.
(touche clignotante) après quoi la hotte s’éteindra. Description de la hotte Fig. 1 1. Panneau de contrôle 2. Filtre anti-graisse 3. Poignée de décrochage du filtre anti-graisse 4. Lampe halogène 5. Écran vapeurs 6. Cheminée télescopique 7. Sortie de l’air (uniquement pour emploi dans la version filtrante) 5.
répéter à nouveau cette opération. Entretien Veillez a débrancher la hotte du réseau electrique avant toute intervention sur celle- ci. Nettoyage La hotte doit être régulièrement nettoyée à l’intérieur et à l’extérieur (au moins à la même fréquence que pour l’entretien des filtres à graisse). Pour le nettoyage, utiliser un chiffon humidifié avec un détersif liquide neutre. Ne pas utiliser de produit contenant des abrasifs.
La société décline toute responsabilité pour d’éventuels inconvénients, dégâts ou incendies provoqués par l’appareil et dérivés de la non observation des instructions reprises dans ce manuel. Cet appareil porte le symbole du recyclage conformément à la Directive Européenne 2002/96/CE concernant les Déchets d’Équipements Électriques et Électroniques (DEEE ou WEEE).
SE - Monterings- och bruksanvisningar Konsultera även bilderna i början av manualen med de bokstavshänvisningar som anges i den beskrivande texten. Följ noga instruktionerna i denna manual. Tillverkaren frånsäger sig allt ansvar för eventuella funktionsfel, skador eller bränder som uppstår på apparaten på grund av att instruktionerna i denna manual inte har respekterats.
en anordning som leder ut röken utomhus (gäller endast Utsugningsversionen). • Utför alla nödvändiga väggarbeten (t.ex.: installationen av ett eluttag och/eller en öppning för avledningsrörets passage). Fläkten är utrustad med fixeringspluggar som passar de flesta typer av väggar/tak. Det är under alla händelser nödvändigt att rådfråga en kvalificerad fackman för att förvissa sig om att materialen är lämpade för den aktuella typen av vägg/tak.
väggen, vidare motsvarar borrmallens nedre del fläktens undre kant. 3. Placera den undre upphängningsbygeln på borrmallen så att den sammanfaller med den streckade rektangeln och markera de två yttre hålen och borra dessa. Avlägsna borrmallen, sätt i 2 väggpluggar och fixera fläktens upphängningsbygel med 2 st. skruvar 5x45mm. 4. Häng upp fläkten på den undre bygeln. 5. Justera avståndet mellan fläkten och väggen. 6. Justera fläktens horisontella position. 7.
(blinkande tangent) varefter fläkten stängs av eller återgår till den tidigare valda hastigheten. OBS: Denna funktion kan ställas in så att fläkten i alla lägen stängs av efter 5 minuters funktion (oavsett om en annan utsugningshastighet (effekt) var inställd tidigare), i detta syfte skall tangenten efter att ha tryckts in, tryckas in igen och hållas intryckt, tangenten börjar blinka vilket indikerar att den önskade funktionen har aktiverats. 6.
Genom att säkerställa en korrekt kassering av denna produkt bidrar du till att förhindra potentiella, negativa konsekvenser för vår miljö och vår hälsa, som annars kan bli följden om produkten inte hanteras på rätt sätt. Byte av Lampor Koppla ur apparaten från elnätet. Varning! Kontrollera att lamporna har svalnat innan ni vidrör dem. Fig. 4 1. Skruva ur plafonden. 2. Ersätt den trasiga lampan. Använd endast halogenlampor max. 20W (G4), och var noga med att inte vidröra lamporna med händerna. 3.
IT - Istruzioni di montaggio e d'uso Consultare anche i disegni nelle prime pagine con i riferimenti alfabetici riportati nel testo esplicativo. Attenersi strettamente alle istruzioni riportate in questo manuale. Si declina ogni responsabilità per eventuali inconvenienti, danni o incendi provocati all'apparecchio derivati dall'inosservanza delle istruzioni riportate in questo manuale.
possibile collegarsi ad un dispositivo di scarico fumi verso l'esterno (solo Versione aspirante). • Eseguire tutti i lavori di muratura necessari (ad es.: installazione di una presa elettrica e/o foro per il passaggio del tubo di scarico). La cappa è dotata di tasselli di fissaggio adatti alla maggior parte di pareti/soffitti. E’ tuttavia necessario interpellare un tecnico qualificato per accertarVi sull’idoneità dei materiali a seconda del tipo di parete/soffitto.
il numero ed il tipo di viti indicato in figura. Con una matita, eseguire una linea sulla parete, sino al soffitto, corrispondente alla linea di mezzeria, faciliterà le operazioni di installazione. 2. Applicare lo schema di foratura al muro: la linea verticale di mezzeria stampata sullo schema di foratura dovrà corrispondere alla linea di mezzeria disegnata sul muro, inoltre il bordo inferiore dello schema di foratura corrisponde al bordo inferiore della cappa. 3.
5. 6. Tasto di selezione velocità (potenza) di aspirazione Intensiva (temporizzata): premere per selezionare la velocità (potenza) di aspirazione, il tempo di funzionamento è di 5 minuti (tasto lampeggiante) dopodiché la aspirazione si spegne o ritorna alla velocità (potenza) di aspirazione precedentemente selezionata.
smaltito in modo corretto, l'utente contribuisce a prevenire le potenziali conseguenze negative per l'ambiente e la salute. Sostituzione Lampade Disinserire l’apparecchio dalla rete elettrica. Attenzione! Prima di toccare le lampade sincerarsi che siano fredde. Fig. 4 1. Svitare la plafoniera. 2. Sostituire la lampada danneggiata. Utilizzare solo lampade alogene da 20W max (G4), avendo cura di non toccarle con le mani. 3. Riavvitare la plafoniera.
ES - Montaje y modo de empleo Consulte tambien los dibujos de las primeras páginas con las referencias alfabéticas del texto explicativo. Aténgase estrictamente a las instrucciones del presente manual. Se declina cada responsabilidad por eventuales inconvenientes, daños o incendios provocados al aparato originados por la inobservancia de las instrucciones colocadas en este manual.
instalación de la campana (con la campana montada) sea disponible un enchufe eléctrico y una descarga para el humo hacia el exterior (solo para la versión aspirante). • Ejecutar todos los trabajos de mampostería necesarios ( ej.: instalación de una toma de corriente y/o agujero para el pasaje del tubo de descarga). La campana está dotada con tacos de fijación adecuados a la mayor parte de paredes/techos.
Reensamblar el marco del filtro de carbón y el de/ de los filtro/s anti grasas y controlar el perfecto funcionamiento de la campana. Instalación modelo para pared Fig. 7 a. Apoyar el grupo aspirante sobre una superficie e introducir la parte inferior de la campana en el mismo. b. Efectuar las conexiones eléctricas entre las dos partes. c. Fijar definitivamente la campana al grupo aspirante con el número y el tipo de tornillos indicados en la figura. 1.
Descripción de la campana 5.
Sustitución de la lámpara Mantenimiento Desconecte el aparato de la red elèctrica. Atención! Antes de tocar las lámparas asegúrese de que esten frías. Fig. 4 1. Desenroscar la protección de la lámpara. 2. Sustituir la lámpara dañada. Utilizar sólo lámparas halógenas de 20W máx (G4) prestando atención en no tocarlas con las manos. 3. Montar la protección de la lámpara.
La correcta eliminación de este producto evita consecuencias negativas para el medioambiente y la salud. en el producto o en los documentos que se El símbolo incluyen con el producto, indica que no se puede tratar como residuo doméstico. Es necesario entregarlo en un punto de recogida para reciclar aparatos eléctricos y electrónicos. Deséchelo con arreglo a las normas medioambientales para eliminación de residuos.
PT - Instruções para montagem e utilização Consultar também os desenhos nas primeiras páginas com as referências alfabéticas indicadas no texto explicativo. Ater-se especificamente às instruções indicadas neste manual. Declina-se qualquer responsabilidade por eventuais inconvenientes, danos ou incêndios provocados ao aparelho, derivantes da inobservância das instruções indicadas neste manual.
nas fases da conexão eléctrica. Além disso, verificar que nas proximidades da zona de instalação da coifa (em zona acessível também com a coifa montada) uma tomada eléctrica se encontre a disposição e seja possível conectar-se a um dispositivo de descarga fumos para o externo (somente Versão aspirante). • Executar todos os trabalhos de alvenaria necessários (por ex: instalação de uma tomada eléctrica e/ou tubo para a passagem do tubo de descarga).
gorduras e controlar o perfeito funcionamento da coifa. Instalação modelo para parede Fig. 7 a. Apoiar o conjunto aspirante sobre um plano e introduzir no mesmo a parte inferior da coifa. b. Executar as conexões eléctricas entre as duas partes. c. Fixar definitivamente a coifa ao conjunto aspirante com o número e o tipo de parafusos indicados na figura. 1. Com um lápis, trace uma linha na parede, até ao tecto, correspondente ao centro do exaustor: isto irá facilitar as operações de instalação. 2.
seguida a coifa desliga. 5. 6. Manutenção Tecla de selecção velocidade (potência) de aspiração Intensiva (temporizada): pressionar para seleccionar a velocidade (potência) de aspiração, o tempo de funcionamento é de 5 minutos (tecla lampejante) em seguida a aspiração desliga ou volta para a velocidade (potência) de aspiração anteriormente seleccionada.
derivantes da inobservância das instruções indicadas neste manual. Este aparelho está classificado de acordo com a Directiva Europeia 2002/96/EC sobre Resíduos de equipamento eléctrico e electrónico (REEE). Ao garantir a eliminação adequada deste produto, estará a ajudar a evitar potenciais consequências negativas para o ambiente e para a saúde pública, que poderiam derivar de um manuseamento de desperdícios inadequado deste produto.
LI231A Ed.