Instructions Manual CMVANILLA – CMVERTIGO - CMZOOM
INDEX EN RECOMMENDATIONS AND SUGGESTIONS ..................................................................................................................... 3 CHARACTERISTICS ............................................................................................................................................................. 4 INSTALLATION.................................................................................................................................................................
RECOMMENDATIONS AND SUGGESTIONS The Instructions for Use apply to several versions of this appliance. Accordingly, you may find descriptions of individual features that do not apply to your specific appliance. INSTALLATION • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation.
CHARACTERISTICS Components (Chic-Vanilla models) Ref. 1 2 3 4 5 6 14 Ref. 11 12h 12c 12d 12e 12g 22 Q.ty 1 1 1 1 3 3 1 Q.ty 4 4 1 6 6 1 12 Q.ty 1 Product Components Hood Canopy complete with: Controls, Light, Filters, Motor. Hood support Plate (with lamp holder). Power supply cable lock Cable raceway Glass Glass fixing plates Pawl Installation Components Wall plugs ø 10 Screws M5 x 70 Screws 2.9 x 9.
Components (Vertigo model) Ref. 1 2 3 4 5 14 Ref. 11 12h 12c 12d 12g Q.ty 1 1 1 1 1 1 Q.ty 4 4 1 4 1 Q.ty 1 Product Components Hood Canopy complete with: Controls, Light, Filters, Motor. Hood support Plate (with lamp holder) Power supply cable lock Cable raceway Glass or Panels the other material Pawl Installation Components Wall plugs ø 10 Screws M5 x 70 Screws 2.9 x 9.
Components (Zoom model) Ref. 1 2 3 4 14 Ref. 11 12h 12c 12g Q.ty 1 1 1 1 1 Q.ty 4 4 1 1 Q.ty 1 Product Components Hood Canopy complete with: Controls, Light, Filters, Motor. Hood support plate. Power supply cable lock Cable raceway Pawl Installation Components Wall plugs ø 10 Screws M5 x 70 Screws 2.9 x 9.
Dimensions EN 7 7
INSTALLATION This hood is designed to be mounted on the ceiling/on a shelf, above a free-standing Hob (min. 650 mm), in: • Ducting version: Evacuation to the outside. • Recirculation version: Internal recirculation. Warning: The F-Light hood is a system comprising hood + lamp, so that two separate electrical wiring systems must be provided, one for the hood and one for the lamp. The Zoom model is not fitted with a lamp.
Ceiling/Shelf drilling and Plate Fixing CEILING/SHELF DRILLING • Use a plumb-line and mark the centre of the cooking hob on the Support Ceiling/Shelf. • Rest the plate against the ceiling/shelf, taking care to keep the limit pawl that has just been fitted in a position facing the installer and the cooking hob (the limit pawl must not be confused with the other 4 used to fix the steel cables that move the Hood). • Mark on the ceiling the centres of the holes in the plate.
FIXING THE PLATE • Lift up the fixing plate, taking care to ensure that the limit pawl is positioned frontally. • Fit the slots onto the two screws previously inserted in the ceiling, and turn until they are at the centre of the adjustment slot. • Tighten the two screws completely and screw in the other two provided; before locking the screws completely it is possible to make adjustments by turning the piece, making sure that the screws do not come out of the adjustment slot.
CONNECTING HOOD-PLATE CABLES N.B. Before continuing with installation it is necessary to move the hood to a height of at least 650 mm from the cooker hob, using a support or the assistance of another person. This is essential, as the hood cables must necessarily be connected to the plate fitted to the ceiling without the weight of the hood bearing on the structure. • The cable fixing system is made up of 3 parts: • Threaded Pawls (a) already mounted on the ceiling plate. • Cable clamp screws (b) provided.
• Attention to the direction of the plate fixed to the ceiling (the limit pawl on the plate fastened to the ceiling has a corresponding hole on the plate cover and on the hood canopy). B C EN • Insert the cables into the safety knobs (c) with the thread at the top.
• Pass the cables through the slots in the threaded pawls (a) and screw the cable locking screws (b) to the pawls themselves. • When the operation has been completed the result must be as shown in the figure for all 4 cables. • At this point we have all 4 cables connected to the plate Bring the cables under tension by pushing them upwards so that they slide inside the cable clamp screw and slide out of the slot in the threaded pawl.
• At this point it is possible to connect up the hood, and the lamp if there is one, to the power supply using the respective power cables. • Close the plate cover using the 3 screws removed previously and the wrench provided • At this point the Hood is suspended.
Connections AIR OUTLET - DUCTING VERSION To install the hood in the ducting version, please refer to the instructions provided in the ducting kit specific to the hood. AIR OUTLET – RECIRCULATION VERSION • Open the lighting unit by pulling on the notch provided. • Remove the grease filter. • Make sure that the Activated charcoal odour filter has been fitted.
LEVELLING THE HOOD • The hood mobile unit must be levelled to allow the movement to operate properly. • The hood is levelled by adjusting the safety pawls. • Rest a spirit level on the hood. • When the safety knobs are pressed upwards, movement of the hood is “unlocked”. By inserting or extracting the cable from the cable clamp screw it is possible to make adjustments that allow the mobile hood body to be levelled. • Once the hood has been set level, the safety knobs must be tightened again.
FIXING THE POWER SUPPLY CABLE • Wind the power cable around its axis so that it forms a spiral from the mobile body to the plate in the ceiling. • It is important to do this to prevent the wire come out from the hood body during the closing of the hood X L • Take the cable clamp 3 provided. • Insert the Power cable in the Cable clamp 3 and screw it to the plate using one of the Screws 12c provided.
FITTING THE GLASS – CHIC-VANILLA MODELS • Take the lamps and insert them in the lamp holders. • They do not have to be screwed in, but simply inserted all the way. 2 12d 12d 22 22 • Fix the glass 5 to the plate using the screws 12d and washers 22 in the top part. • Fix the glass elements together at the bottom using the glass fixing plates 6 with screws 12e and washers 22. 5 6 12e 22 FITTING THE GLASS – VERTIGO-KALEIDOS-LUXIA MODELS • Take the lamps and insert them in the lamp holders.
USE Control panel L Button L T1 Function Turns the lights On/Off. Hood Down Press for 2 seconds to raise the Hood. Press briefly to turn the Motor On/Off. Hood Up Press once: The Hood lowers. Press a second time: The Hood Stops. When the movement has been completed the motor turns on at Speed two. T1 Display On/Off Off/Off Warning: The Hood controls only control the Hood functions. The Lighting unit has a completely separate power supply and a separate switch.
REMOTE CONTROL The appliance can be controlled using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type (not included). • Do not place the remote control near to heat sources. • Used batteries must be disposed of in the proper manner. Control panel Button Function Display Turns the Motor On/Off. - Hood Closed: - Press the button briefly to start lowering the hood - It will stop when the button is pressed again.
MAINTENANCE Grease filter The filter must be cleaned every 2 months of operation, or more frequently for particularly heavy usage, and can be washed in a dishwasher. CLEANING METAL SELF- SUPPORTING GREASE FILTER • Open the lighting unit by pulling on the nocth. • Remove the filter one by one pushing it towards the back side of the hood unit and simultaneously pulling downwards. • Any kind of bending of the filter has to be avoided when washing it.
Lighting LIGHT REPLACEMENT 20 W halogen light. • Remove the snap-on lamp cover by levering it from under the metal ring, supporting it with one hand. • Remove the halogen lamp from the lamp holder by pulling gently. • Replace the lamp with a new one of the same type, making sure that you insert the two pins properly into the housings on the lamp holder. • Replace the snap-on lamp cover. Lighting Unit Lamps Vanilla Vertigo G9 -- Energy Saving 9W Attention: Bulbs are not provided.
Additional information for the installation technician • Open the lighting unit by pulling on the notch provided. • Apply the label, indicated the type of lighting, on the Hood as indicated in the figure (Rif.A). B A Procedure to be used in case of malfunction on the movement • Check that the fuse is properly inserted and that it has not burned out, for replacing the fuse open the lighting unit and unscrew the fuser holder and replace it with one having the same characteristics (Rif.
991.0266.
