Datasheet

33
Series CG1K
8 x J
Wθ
°
10°
WA
GA
TBTA
øD
F
øI
R0.4
TA
øD
F
øI
C
4 x TC
4 x TC
Width across
flats
B1
øE
0 −0.05
øE
0 −0.05
øE
0 −0.05
H1
R0.4
R0.4
H1
ZZ + Stroke
S + StrokeH
A
C
NA
C
C
NA
8 x J
A
HS
+ Stroke
ZZ + Stroke
WB
GB
GB
TB
Width across flats KA
MM
AL
AL
R0.4
F
GA
2 x RcP
MM
Width across flats KA
Width across
flats
B1
H
ZZ
+ Stroke
MM
thread depth A1
øE
0 −0.05
F
Cushion valve, Width across flats WH
2 x P
Female rod end
Female Rod End
[mm]
[mm]
[mm]
ø40 to ø63
With air cushion
ø20 to ø63
With rubber bumper
With Air Cushion
Note) ( ): Denotes the dimensions for
long stroke.
Note 1) Dimensions for each mounting bracket are the same as those for the CG1 standard or long stroke model. Refer to pages 9 to 14.
Note 2) ( ): Denotes the dimensions for long stroke.
Note 3) When the stroke exceeds the standard stroke, it is beyond the guarantee.
Bore
size
WA WB Wθ WH
40
17 15 (17) 20° 1.5
50
18 16 (18) 20° 3
63
18 17 (18) 20° 3
Bore
size
A
1 HMM ZZ
20
8 13 M4 x 0.7 84 (92)
25
8 14 M5 x 0.8 85 (93)
32
12 14 M6 x 1 87 (95)
40
13 15 M8 x 1.25 95 (104)
50
18 16 M10 x 1.5 108 (120)
63
18 16 M10 x 1.5 108 (120)
Bore
size
Stroke range
AALB1 C D E F GA GB H H1 I J KA MM NA P S TA TB TC ZZ
Standard Long stroke
20
Up to 200 201 to 1500 18 15.5 13 14 9.2 12212 10 (12) 35526 M4 x 0.7 depth 7 8 M8 x 1.25 24 1/8 69 (77) 11 11 M5 x 0.8 106 (114)
25
Up to 300 301 to 1500 22 19.5 17 16.5 11 14 2 12 10 (12) 40631 M5 x 0.8 depth 7.5 10 M10 x 1.25 29 1/8 69 (77) 11 11 M6 x 0.75 111 (119)
32
Up to 300 301 to 1500 22 19.5 17 20 12 18 2 12 10 (12) 40638 M5 x 0.8 depth 8 10 M10 x 1.25 35.5 1/8 71 (79) 11 10 (11) M8 x 1.0 113 (121)
40
Up to 300 301 to 1500 30 27 19 26 16 25 2 13 10 (13) 50847 M6 x 1 depth 12 14 M14 x 1.5 44 1/8 78 (87) 12 10 (12) M10 x 1.25 130 (139)
50
Up to 300 301 to 1500 35 32 27 32 20 30 2 14 12 (14) 58 11 58 M8 x 1.25 depth 16 18 M18 x 1.5 55 1/4 90 (102) 13 12 (13) M12 x 1.25 150 (162)
63
Up to 300 301 to 1500 35 32 27 38 20 32 2 14 12 (14) 58 11 72 M10 x 1.5 depth 16 18 M18 x 1.5 69 1/4 90 (102) 13 12 (13) M14 x 1.5 150 (162)
that protrudes. Tighten it by giving consideration to prevent the tightening
torque from being applied to the non-rotating guide.
2. When replacing rod seals, please contact SMC.
Air leakage may be happened, depending on the position in which a
rod seal is fi tted. Thus, please contact SMC when replacing them.
Caution
1. Avoid using the air cylinder in such a way that
rotational torque would be applied to the piston rod.
¡ If rotational torque is applied, the non-rotating guide will become deformed,
thus affecting the non-rotating accuracy. Refer to the table below for the
approximate values of the allowable range of rotational torque.
¡ To screw a bracket or a nut onto the piston rod, make sure to retract the
piston rod entirely, and place a wrench over the fl at portion of the rod
Caution on Handling/Disassembly
Be sure to read before handling. Refer to back cover for Safety Instructions. For Actuator and Auto Switch
Precautions, refer to “Handling Precaution for SMC Products” and the Operation Manual on SMC website,
http://www.smcworld.com
Precautions
Allowable rotational torque
N·m or less
ø20 ø25, ø32 ø40, ø50, ø63
0.2 0.25 0.44
Basic