Electronic Toilet Bidet Seat for Elongated French Curve Toilets smartBidet® ® SB-2400ER * This product was manufactured for household use only. * Read all operating instructions before installation and use. * Please save this operating instruction manual and place in an easily accessible location. + Due to ongoing product improvements, external appearance and specifications are subject to change without notice.
READ ALL INSTRUCTIONS BEFORE USING. DANGER To reduce the risk of electrocution. « Do not use while bathing. + Do not place or store product where It can fall or be pulled Into a tub or sink. « Do not place in or drop into water or other liquid. N Do not reach for a product that has fallen into water. Unplug immediately. WARNING To reduce the risk of bums, electrocution, fire or injury to persons. « Close supervision is necessary when this product is used by, on, or near children or invalids.
CAUTION To reduce the risk of injury to persons or damage to the product or the property. + Do not place heavy objects or step on the unit. Doing so may cause product damage or injury. » When cleaning the unit, do not use any chemicals. Clean the unit with a moist, well-wrung soft cloth. For excessive stains, use a soft cloth moistened with mild dish washing detergent and wipe with a dry cloth. Using chemicals may cause product damage. « Do not slam the lid. Slamming the lid may cause product damage.
GROUNDING INSTRUCTIONS « This product should be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded. DANGER Improper use of the grounding plug can result In a risk of electric shock.
SB 2400ER Inlet Adapter i \_ Backbit LED Night light ~ Nozzle Is aluminum coated J Remote Control ~ own wer wv mm mar hoe eT Si: Rom < Remote control > simpatico Operation Pane
Mounting Bolts Cone Sackings Washers.
+ Auxiliary simple operation panel is on the body of the unit. However, due to its limited functionality, It cannot be used fo adjust water pressure. When water pressure control is needed press any of the wash buttons on the remote control and adjust water pressure using the button. + Dropping of spilling liquids on the remote may cause damage. ORR “5 «If the seat is occupied, the unit will make a beep.
(ITE + Start nozzle movement by pressing the" Posterior " or" Feminine” button while cleansing. * Stop nozzle movement by pressing the " Posterior " or" Feminine” button again. \ Water Pressure Adjustment © The unit remembers the most recent water pressure settings. \« Water pressure an be adjusted by pressing the button. \. Nozzle Position Adjustment * Press the "FR" or "BK" button to adjust the nozzle position during” Posterior * or "Feminine function.
@ Warm Air Dryer Temperature Adjustment * The unit remembers the most recent warm air temperature setting. Press button to adjust the temperature of the warm air. (Levels 1~5) * To activate the LED Nightlight, press the "LIGHT" button. The Nightlight activates automatically when iris dark. To cancel the LED Nightlight function, press the "LIGHT" button again and Nightlight will go off. « When LED Nightlight function is on, the bidet can be used without muting on the toilet light.
Auto Cleansing * To activate the automatic (auto) cleansing function, press the "AUTO CLEAN" button. The "OSCILLATE"™ wash function and warm air dryer will operate for 1 minute each after activation. * Default settings for this function are: “Level 3* for Water Pressure, “Level 2” for Warm Air Drying Temperature and “Level 3*for the Nozzle Position. These settings may be adjusted to suit user preference.
EGE SNE * When the seat temperature is set to it will be reduced automatically when the unit is in use for more than 30 minutes, This protects the user from burns, which can occur when sitting on the unit fora long time, # Seat temperature can be returned to *HI" by manually resetting temperature or moving away from the seat. \. J Self-Cleaning Nozzle * Before and after each operation, the self-cleaning nozzle function will cleanse the nozzle head.
Caution before installation! A + Make sure the size and shape of the bidet seat are compatible with the toilet. « Checkmate parts are included and ready for installation. Please check if other parts are needed for your installation. « Do not connect the power until installation is complete. 0 Remove the existing toilet seat. * Remove the existing toilet seat and lid by removing the: fastening nu nuts from below. » Keep the detached seat, lid, and nuts for later use.
® Disconnect the water supply line from the toilet water tank and install a T-valve. = Yar supply hose Gg, @ Line up the bolt slots in the Base piste with the bolt holes in the toilet bow. « 5.5” hole spacing is required for installation. @ Insert mounting bolts through the bolt slots and into the bolt holes in the toilet. Securely fasten the base plate by installing the cone packing and washers as shown below, and tightening the mounting bolts and nuts.
< Toilets with Bolts Tightened from Above > Reuse the mounting bolts from the existing toilet I Mounting bots seat with the bolt cases included with the bidet. Bobcats —4, | a tot seat 0 Place the base plate so that the slots align with the bolt holes in the toilet. ® Place the bolt cases on the base plate. $ 0 Fasten the base plate using the bolts removed from the existing toilet seat. 0 Connect the water supply hose to the bidet.
0 Attach the remote control mounting plate to the wall with double-sided adhesive tape. a Insert batteries into the remote control unit, as shown below, and mount the unit to the mounting plate, Battery cover batteries type /1.
0 Open the shut-off valve by muting counterclockwise. 0 Check for any water leakage from hose connections. Shut-off valve ® Plug in the power cord. If the power indicator light does not illuminate after plugging in the power cord, press any button except ‘FR’ "BK “HI, or “LO” buttons to illuminate the indicator. WARNING Do not invert or otherwise move the bidet unit after it is connected to power. Doing so may cause damage to the bidet unit.
To detach or move the unit, follow the instructions shown below. 0 Unplug the power cord. Shut off the water supply by the turning the shut-off valve clockwise. Then completely drain the toilet water tank. ® Disconnect the flexible hose from the T-valve, detach the bidet unit from the base plate, and unfasten the base plate from the toilet. To detach the unit, pull it forward while lifting the front end, as shown, 0 Completely drain the bidet's water tank by removing the drain plug from the bottom.
Cleaning IRE Ey 0 Shut off the water supply by the turning the shut-off valve clockwise. Then completely drain the toilet water tank. ® Disconnect the water supply hose from the water inlet adapter. If the hose is difficult to disconnect, such as from non-standard toilet bowls, detach the main bidet unit from the toilet before disconnecting the hose from the adapter. ® First remove, clean, and reinstall the strainer from the water inlet adapter.
External Cleaning « Do not use ary harsher strong household chemicals. Using abrasive materials, chemicals, and so on could damage the plastic exterior. We recommend using baking soda mixed with vinegar fo clean the bidet. + When using strong household chemicals to clean your toilet, make sure that the bidet seat does not come into contact with the toilet until iris fully dry. + Do not spray water onto the unit. Wipe it with a tightly wrung damp soft cloth.
ank (Reservoir) 0 First, disconnect the power cord. 6 Close the shut-off valve by turning it clockwise. ® After placing a container (4-liter capacity) under the drain hole, 0 remove the drain plug and completely drain the bidet's water tank. Plug in the power cord and confirm that bidet power is ON. 6 Adjust the water temperature level to“LO" or higher. Do not switch off the water temperature level. © Before extended periods of disuse, drain the bidet's water tank.
Check the following items before calling for service. Unit does not function stall * The power is OFF. Check to see if GFC has tripped. = Check by pressing any button except "HI", "LO", *FR", "BK" buttons on the remote control. ® Check if you're activating the skin sensor. » The power cord is disconnected. + There is a power failure or interruption. Posterior, Feminine Dryer, Auto clean do not operate = A seat cover or other object is covering the seat, = Check whether there is anything on the seat.
400! Power Supply 120V-~, 60Hz Max. Power Consumption: 660W Length of Power Cord ‘Water Supply Connection Direct connection to the water supply ‘Water Supply Pressure (98 735kPa) Water Lansing] Max. (0.95 £ /min} Flow Rate | Bidet Max. (0.95 £ /min} Water Pressure ans Ady 5 Levels Adl emp. Normal Temp, 98.6'F (37 C), 104°F (40°C) Hester Capacity s00W Safety Device Thermal Fuse, Thermostat, Water Level Sensor Temp.
General Limited Warranty Covered Citrons Solutions Inc will warrant to the original retail buyer only, which falls in normal use and within the applicable periods specified below. Citrons Solutions Inc replacements will be warranted to the original purchaser of the products only.