Use and Care Manual

301
Repair Parts and Maintenance Guide
The information contained in this document is subject to change without notice.
1A
1B
Item Part Description
No. No.
1A ESD-216-A Spout Assembly (Models ESD-200 & ESD-250)
1B ESD-235-A Spout Assembly (Models ESD-300 & ESD-350)
2 ESD-218 Mounting Hardware Kit (Includes items 2A and 2B)
2A ESD-222 Rubber Gasket
2B ESD-620 Flange Nut
3 ESD-209-A Motor Assembly
4 ESD-227 Plug-in Transformer (Hardwire Models ESD-200 & ESD-
300)
5 ESD-210 Battery Pack — Includes 4 D-size batteries, Screws and
Anchors for Battery Compartment and Wall Clips for Power
Cord (Battery Models ESD-250 & ESD-350)
6 ESD-217 Lotion Soap Refill Cartridge 800 ml
(up to 1000 hand washes)
ESD-232 Lotion Soap Refill Cartridge 1600 ml
(up to 2000 hand washes)
ESD-231 Anti-bacterial Soap Refill Cartridge 800 ml
(up to 1000 hand washes)
ESD-233 Anti-bacterial Refill Cartridge 1600 ml
(up to 2000 hand washes)
7 ESD-223 D-size Alkaline Batteries (4 required)
(Models ESD-250 & ESD-350)
8 ETF-299-A Trim Plate for ESD-20080, ESD-25085, ESD-30880 &
ESD-35187 Combination Soap Dispenser and Faucet
2A
3
2B
7
8
6
4
INCLUDED
WITH
BATTERY
PACK
5
ESD-200/250
ESD-300/350
ESD-200/250 Series Soap Dispensers
ESD-300/350 Series Soap Dispensers
When the Soap Bottle is empty,
a new Bottle must be used. The
Bottle furnished with the unit is not
designed to be refilled. Altering the
Bottle and refilling it with soap will
void the warranty of the product.
Refills are available through your
local plumbing or janitorial supply
distributor.
Soap Refill Cartridges Available:
• ESD-217 — 800 ml. bottle of
Lotion Soap
• ESD-232 — 1600 ml. bottle of
Lotion Soap
• ESD-231 — 800 ml. bottle of
Anti-bacterial Soap
• ESD-233 — 1600 ml. bottle of
Anti-bacterial Soap
Can also be replaced with TC
®
OneShot
®
Soap Bottles listed in
chart.
I. Red LED light is flashing.
A. Refill bottle is low. Check the fill level and change as needed.
B. Reset button was not pressed after the refill was installed. Press and
release reset button.
C. If reset button is held down more than one second, the red light will stay
on. To turn the red light off, press the reset button quickly and the red
light will go off.
2. Yellow LED light is flashing (Models ESD-250 & ESD-350 only).
A. Batteries are low. Replace with four (4) new D-size alkaline batteries.
3. Preventing soap from dispensing while cleaning.
A. Place your finger over the upper right hand or left hand corner of the
sensor lens.
4. The dispenser does not activate properly when hand is placed under
spout.
A. In rest rooms with fluorescent lighting, lighting that may be dying out or
not burning at full intensity will cause interference with soap dispenser.
Replace fluorescent tube(s) and soap dispenser will then function
normally. Cool, white tubes are recommended.
5. Soap does not dispense when user “waves” their hands under the
spout.
A. Hands must be held “steady” under the spout for the dispenser to work.
6. Dispenser rotates due to users moving the spout.
A. Tighten the existing flange nut on the shaft of the spout under the
counter.
B. If this problem continues, you can order a second “flange nut” (ESD-620)
from Sloan Valve.
7. Soap does not dispense.
A. Check that your power source is plugged in correctly.
B. Make sure that batteries have been installed properly
(Models ESD-250 & ESD-350 only).
C. Make sure the pump is open on the refill bottle (see Step 5).
8. Tube pulls out of the refill bottle.
A. The tubes have been “stitched” to prevent their removal, however please
ensure that your housekeeping staff does not pick the bottle up or carry it
by the tube.