Owners manual

ManualsBrandsSKYJACKER ManualsAutomotiveSkyjacker 7296 Steering Stabilizer Dual Kit

99-06 GM K1500 4WD

Dual Steering Stabilizer

Part # 7296

PARTS LIST:

ITEM# DESCRIPTION QTY

7500WS WHITE STEERING DAMPER 2

B12RS RED BOOT 2

BTIE RED BOOT TIE 2

HSS HYDRO SHOCK DECAL 2

C966DSMB-S GM 1/2T,DUAL STAB MAIN BRKT 1

C966DSST-S GM 1/2T,DUAL STAB TAB BRKT 2

140629 STEERING STAB STUD PACKAGE 2

142120 STEERING STAB WASHER PKG. 2

HOURGLASS 5/8 HOURGLASS 5/8 SHOCK BUSH 2

STEM BUSH-SST STEM BUSH-STEERING STAB 4

ITEM# DESCRIPTION QTY

12SAEW 1/2 SAE WASHER 4

38X1TCFB 3/8 X 1 THRD-CUT FLANGE BLT 2

516X114X134U 5/16 X 1 1/4 X 1 3/4 U-BOLT 2

516CTN 516-18 COARSE N/I LOCK NUT 4

516SAEW 5/16 SAE WASHER 4

58X5FTB 5/8 X 5 FINE THREAD BOLT 2

58FTN 5/8-18 NYLON INSERT LOCKNUT 2

58SAEW 5/8 SAE WASHERS 4

I-7296 INST SHEET FOR 7296 1

Important Note: This steering stabilizer kit is designed for the 99-06 GM 1/2 ton 4WD. It will fit lift

heights from 4"- 6”. This kit will NOT work on vehicles with a lift kit that relocates the upper

A-arms.

Installation:

1. Park the vehicle on flat level ground & set the emergency brake.

2. Place the front tires / wheels to a straight forward position.

3. While supporting the front cross member with a floor jack, remove the

front lower A-arm bolt at the frame. (If installing on a vehicle with 4”

or more lift, it will be the upper front bolt on the after market cross

member. Remove the bolt using a 15/16 socket. (See Photo # 1)

Note: A 5/8" x 5” fine thread bolt, washers, & nuts are supplied in

case the existing bolts are not long enough.

4. Once the bolt is removed, reinstall with the new Skyjacker outer

stabilizer bracket. Be sure to install the bolt pointing toward the front

of the vehicle. Drill the mounting hole using a 5/16" drill bit & install

the supplied 3/8" thread cutter bolt. (See Photo # 2 / Arrow Shows

the 5/16" Drill Bit)

5. Attach the new Skyjacker shock stud to the new bracket being sure

to use two of the supplied 1/2" washers between the new shock stud

& new bracket. (See Arrow in Photo # 3)

Photo # 1

Photo # 2

I-7296 REV2 3-13 Pg 1

www.skyjacker.com

Photo # 3

Summary of content (2 pages)

PAGE 1
99-06 GM K1500 4WD Dual Steering Stabilizer Part # 7296 www.skyjacker.com PARTS LIST: ITEM# DESCRIPTION QTY 7500WS WHITE STEERING DAMPER 2 B12RS RED BOOT 2 BTIE RED BOOT TIE 2 HSS HYDRO SHOCK DECAL 2 C966DSMB-S GM 1/2T,DUAL STAB MAIN BRKT 1 C966DSST-S GM 1/2T,DUAL STAB TAB BRKT 2 140629 STEERING STAB STUD PACKAGE 2 142120 STEERING STAB WASHER PKG.
PAGE 2
6. Install the new Skyjacker main bracket to the center steering link using the supplied 516" u-bolts, washers, & nuts. Measure from the center of the pitman arm 9” & tighten the new main bracket. Adjust the main bracket as needed, so both stabilizers are pulled out half way. (See Photo # 4) Photo # 4 7. Attach both of the new Skyjacker steering stabilizers to the new outer brackets & main bracket. (See Photo # 4 & # 5) 8.