RANGE HOOD INSTALLATION, USE AND CARE MANUAL
1. CONTENT 1.1 Your safety 1.2 Installation Warning .................................................................................1 1.3 During use ............................................................................................2 1.4 Electric Cord .........................................................................................2 2. VENTILATION 2.1 DUCTED MODE ......................................................................................2 2.2 RECIRCULATING MODE ..............
From the Manufacturer Please read this user manual carefully before attempting to operate the appliance and store it in a safe place for future reference. This appliance and its packaging are produced by processes that minimize waste and respect the environment. Please help us to continue this effort to protect the environment by using the appliance efficiently and dispose of the packaging in a responsible manner. 1. FOR THE USER 1.
2. Ventilation Ducted or Re-circulating mode Depending on your requirement, this appliance can be configured to operate in the ducted or re-circulating modes. 2.1 Ducted Mode: Fire proof ducting system of 6inch diameter vent the fumes through a suitable outlet. In the ducted mode, only the grease filters are installed. 2.2 Recirculating Mode: Fumes are filtered for grease and odour through the grease filters and the charcoal filters respectively and re-introduced into the kitchen environment.
3 Instructions on control board Use the low speed for simmering, medium speed for light cooking. Use the high speed for frying or heavy cooking. The range hood can be operated in two ways which are gesture sensor control and touch control. 3.1.1 Gesture sensor control A. Within distance of 10-15cm to the switch, wave hand once from left to right for turning on(LED screen shows”1”). Repeat the waving from left to right, the fan runs at mid speed (LED screen shows “2”).
C Left Motor: When the fan is working at low speed (LED screen shows”F1”), Press C once, the fan runs at mid speed (LED screen shows “F2”). Press C again, the fan runs at high speed (LED Screen shows “F3”). D Right Motor: When the fan is working at low speed (LED screen shows”F1”), Press D once, the fan runs at mid speed (LED screen shows “F2”). Press D again, the fan runs at high speed (LED Screen shows “F3”). E Double Motor Minus: Decrease fan speed.
4. Cleaning & Maintenance Guide SAFETY WARNING: ALWAYS SWITCH OFF AND UNPLUG FIRST! NEVER PUT YOUR HAND INTO AREA HOUSING OF THE FAN WHILE THE FAN IN OPERATING! For optimal operation, clean range hood and all baffle/spacer/filter/grease tunnel/oil container regularly. Regular care will help preserve the appearance of the range hood. 4.1 Cleaning Exterior surfaces: • Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent (e.g.
Contents 4.3 Replacing Filters: Before proceeding to the wear installation, check contents of the box. If items are missing or • Should aluminum grease filters out due tothe age and prolonged use, please contact damaged, contact the manufacturer. your local reseller for replace sure thatreplace the following items are included: ment filters. Make (Note: Also damaged filter that has punctured or broken mesh, bent or broken frame.) BCSD Series : 4.
5.Range Hood Installation 5.1 Wall mounted range hood 5.1.1 Parts Diagram Main Parts INSTALLATI0N MANUAL 5.1.2Installation requirement 1. Do not install the range hood near open doors and windows to avoid reduced performance. (Fig. 1) 2. Install the range hood directly above the cooktop. The optimal distance between the cooktop and lower edge of the range hood is 24” to 36”. (Fig. 2) Install at the height appropriate to your ceiling. Make sure the chimney reaches the ceiling.
3.For optima performance, do not over extend the exhaust tube and avoid unnecessary bending. (Fig. 3) 4.After hanging the unit on the wall, ensure the range hood is straight and leveled. (Fig. 4） 5.The air outlet must be connected to chimney flumes or combustion gas ducts.
. Parts diagram Main parts INSTALLATI0N MANUAL INSTALLATION 9
5.1.3Installation Step 1: Find the center of the wall where you are installing the hood. Make sure there is sufficient bracing to hold the weight of the hood. Mark your center line and measure out from center to find your two mounting points. Make sure your mounting points are level when you mark them. It is recommended to install the hood directly into wood supports. fig 1 Step 2: Mark your mounting points and install the two mounting screws provided leaving the heads out 1/4” to mount hood.
. Step 6: Install the 2 part chimneys on top of the hood by sliding the inside section up Until the vertical vent slots are visible. Then put both pieces on top of the hood and secure the lower portion with the provided screw at the bottom. fig. 5 Step 7: Slide the upper portion up and over the top mounting bracket aligning the holes and securing with the screws provided. fig.
5.2 Stainless Steel Insert Range Hood 5.2.
5.2.2 Installation requirement • Vent system must terminate to the outside (roof or side wall). • Do not terminate the vent system in an attic or other enclosed area. • Do not use 4” (10.2 cm) laundry-type wall caps. • Use metal/aluminum vent only. Rigid metal/aluminum vent is recommended. • Do not use plastic vent. • Always keep the duct clean to ensure proper airflow. • It is recommended that the range hood be vented vertically through the roof through 6” (15 cm) round metal/ aluminum vent work.
5.2.3 Installation There are two optional installation ways. You may choose one of the ways depending on your cabinet. WAY ONE Step 1 Pleas make sure the cut out size is correct before installing the range hood. Install the back draft base to the range hood. Step 2 Secure the undermount into cavity Using screws, all screws are installed From the bottom of the range hood into The cabinet.
5.3 Under Cabinet Range Hood 5.3.
5.3.2 Installation Way one: Step 1. Fix the two pieces of hangings by using the screws where are already screwed on the two sides of the range hood. Step 2. Drill 2 holes on the wall, use two iron expansions to fix the range hood onto the wall. Step 3. Use screws and plastic expansion to strengthen stability of the range hood. Way two: Step 1.Drill 4 holes on the bottom of the cabinet. Step 2. Use four iron expansions to fix the range hood under cabinet. 6 FOR THE INSTALLER 6.
6.2. Troubleshooting Fault Possible Cause Solution Fan switch turned off Select a fan switch position. Fan switch failed Contact service center. Motor failed Contact service center. House fuses blown Reset/Replace fuses. Mains power cable is loose or disconnected Refit mains power cable to power outlet. Switch power outlet on. Lights not working Broken or faulty bulbs Replace bulbs as per this instruction.
7. Wiring diagram 7.1.1 Three speed touch control wiring diagram 7.1.
7.1.3Touch control control wiring diagram 7.
