Installation Instructions

ManualsBrandsSkatePlate ManualsCircular Saw Blades & Accessories& SkateGuide Combo Pack - Sidewinder

BOSCH CS10, GKS190, PKS55A*, PKS55-2A*

BOSTICH BTE300K

BLACK & DECKER *CS1250L

CRAFTSMAN 10870, 27311, CMES510

DEWALT DWE550*, DWE560-EXB, DWE560-K, DWE560-GB, DWE560-LX,

DWE575, DWE575K,DWE575SB, DWE576K, DWE576K-LX,

DCS570B Cordless*, DCS575 Cordless*, DCS575B, Cordless*

DCS577B Cordless, DCS577XI Cordless.

DEXTER POWER NC1300CS*

EVOLUTION R185CCS*, R185CCSL240*

HITACHI C7SB2, C7SB3, C7SB3M*, C7UR, C7BUR*, C7BMR, C7ST

KOBALT K15CS-06AC

MAKITA 5007F, 5007FA, 5007MG/MGA, 5007NK, 5008MGA, 5740NB,

XSR01Z Cordless*, XSH01Z Cordless*, XSH07ZU Cordless,

XSH06Z Cordless, HS6601*

MILWAUKEE 6390-20, 6390-21, 6394-21, 2631-20 Cordless*

PORTER CABLE PC13CSL*, PC13CSLK*, PC15TCS, PC15TCSMK, PCTSM, PCE300, PCE310

RIDGID R32021, R32022, R32051, R8652 Cordless*, R8653B Cordless*

RYOBI CSB135L*, CSB144LZK*

SKIL 5080-01*, 5180-01*, 5280-01, 5380-01*, 5480-00*, 5480-01*, 5580-00*,

5582-00*, 5585-01*, 5587-01, 5680-01, 5680-02, HD5687, SPT67FMD-01,

SPT67FMD-22, SPT67WE-01, SPT67WL01, SPT67WM-22,

SPT67WMB-01, SPT67WMB-22

STANLEY FATMAX FME300K-QS, FME301

WARNING

Read and understand all instructions. Failure to follow all instructions listed below may

result in electric shock or serious personal injury.

SAVE THESE INSTRUCTIONS

Follow Instructions For Your Saw

Be sure to follow all of the safety instructions for your saw. Wear eye protection and use all

recommended protective equipment.

Unplug Your Saw Before Installing or Adjusting the SKATEPLATE®

Disconnect the plug from the power source before installing or making any adjustments to

the SKATEPLATE®. These preventive safety measures reduce the risk of starting the saw

accidentally. Remove all adjusting keys or wrenches before turning the saw on.

Secure the Work Place

Use clamps or other practical way to secure and support the work piece to a stable

platform. Holding the work by hand or against your body is unstable and may lead to loss

of control. NEVER hold piece being cut in your hands or across your leg. It is important to

support the work properly to minimize body exposure, blade binding, or loss of control. Do

not force the saw.

SKATEPLATE

Use and Care

Check for misalignment or binding of moving parts, breakage of parts, and any other

condition that may affect operation of the SKATEPLATE®. If damaged, replace or repair

before using. Certain cleaning agents such as gasoline, carbon tetrachloride, ammonia,

etc. may damage plastic parts. Never clamp or tie the lower guard into the open position. 

Circular saws are not designed or intended to be used as table saws.

KICKBACK

KICKBACK may occur with the SKATEPLATE®. NEVER place your hand behind the

saw blade since KICKBACK could cause the saw to jump backwards over your hand.

Keep your body positioned to either side of the saw blade, but not in line with the saw

blade. Follow all of the instructions for your saw to prevent K ICKBACK.

(2) Spacers

(4) 5/8” Locking Bolts

(1) Locking Bolt

(3) Locking Slides

(1) Foot Pad

(1) Universal

Locking Slide

SKATEPLATE

Hardware

(1) Handle Shoulder Bolt

(1) Cap Screw

SKATEGUIDE

Hardware

LIMITED WARRANTY OF CIRCSAW TECHNOLOGIES, LLC PRODUCTS

CircSaw Technologies LLC (“Seller”) warrants to the original purchaser only, that all SKATEPLATE® and SKATEGUIDE® products will be free from defects in material or workmanship for a period of 90 days from

date of purchase.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall be the repair or replacement of

parts, without charge, which are defective in material or workmanship and which have not been misused, carelessly handled, altered or repaired by persons other than Seller or its Factory Service Center. To make

a claim under this Limited Warranty, you must (a) contact CircSaw Technologies LLC at www.skateplate.com to obtain a Warranty Return Authorization, and (b) return the complete product, shipping prepaid, to the

CircSaw Technologies LLC Factory Service Center specified.

SELLER DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF “MERCHANTABILITY” AND “FITNESS” FOR A PARTICULAR PURPOSE, AFTER THE 90-DAY

TERM OF THIS WARRANTY. SOME STATES IN THE U.S.A. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,

SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR INJURY OR LOSS OF PROFITS) ARISING FROM

THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.A. AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL

DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO STATE IN THE U.S.A, PROVINCE TO PROVINCE IN

CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO.

Place the provided 1” locking bolt with rotating foot into

Location 1. Leave in the up position.

Some saw plates may require use of the provided foot

pad for a more secure hold. Place one of the (4) provided

5/8” bolts into the SKATEGUIDE® locking location.

Leave in the “up” position.

Insert the (3) rear Locking Slides into the three openings

as indicated. Some saw plates may require use of the

provided universal locking slide for a more secure hold.

Some pressure will be required to initially snap the

Locking Slides into position.

Insert the (3) remaining 5/8” Locking Bolts into the

Brass-threaded inserts.

STEP 2

STEP 3

SKATEGUIDE

Can be used as a Reverse Guide by

mounting the roller body in the opposite direction as

shown.

Reverse the Roller Head and install the cap screw on

the opposite side. Install handle with the provided

shoulder bolt and tighten by hand.

Assemble SKATEGUIDE® by inserting cap screw as

indicated. Install handle with the provided shoulder

bolt and tighten by hand.

If a more permanent installation is required, use

appropriate thread-lock fluid.

STEP 1

ASSEMBLY

SKATEPLATE

Sidewinder fits the following Saw Models:

SKATEPLATE

Sidewinder se ajusta a los siguientes modelos de sierra:

SKATEPLATE

Sidewinder (à entraînement direct) s'adapte aux modèles de scie suivants:

SAW BRAND

MARCA DE SIERRA

MARQUE DE LA SCIE

SAW MODEL

MODELO DE SIERRA

MODÈLE DE LA SCIE

*REQUIRES PROVIDED SPACER, *REQUIERE EL USO DEL SEPARADOR

SUMINISTRADO CON EL PRODUCTO, *UTILISER L'ENTRETOISE FOURNIE

VISIT WWW.SKATEPLATE.COM FOR THE LATEST SAW FITMENT GUIDELINES

VISITE WWW.SKATEPLATE.COM PARA CONOCER LAS ÚLTIMAS ESPECIFICACIONES DE MONTAJE DE LA SIERRA

ALLEZ SUR WWW.SKATEPLATE.COM POUR EN APPRENDRE PLUS SUR LES DERNIÈRES DIRECTIVES

CONCERNANT LE MONTAGE SUR LA SCIE

Summary of content (2 pages)

PAGE 1
SKATEPLATE ® Sidewinder fits the following Saw Models: SKATEPLATE ® Sidewinder se ajusta a los siguientes modelos de sierra: SKATEPLATE ® Sidewinder (à entraînement direct) s'adapte aux modèles de scie suivants: SAW BRAND SAW MODEL MARCA DE SIERRA MODELO DE SIERRA MARQUE DE LA SCIE MODÈLE DE LA SCIE BOSCH CS10, GKS190, PKS55A*, PKS55-2A* BOSTICH BTE300K BLACK & DECKER *CS1250L CRAFTSMAN 10870, 27311, CMES510 DEWALT DWE550*, DWE560-EXB, DWE560-K, DWE560-GB, DWE560-LX, DWE575, DWE575K,DWE575SB, DWE57
PAGE 2
STEP 4 From the SAW COMPATIBILITY GUIDE determine if the (2) provided Nylon Spacers are required for your Saw Model. Insert into the indicated positions. STEP 3 Push the Locking Slides forward securing against saw base plate while tightening bolt. INSTALLATION WARNING! ALWAYS UNPLUG YOUR POWER TOOL WHEN CHANGING SET UP! *Note: Locking slide A will not always come into contact with the some models of saw base plates. Slide forward and lock into place.