Metal Gazebo 12'X16'FT G30006 Metal Gazebo 12'X16'FT G30006
Outdoor Furniture We are a professional furniture provider with top-notch factories and outstanding designs, Our mission is to provide consumers with new lifestyles. By collecting consumer feedback, we constantly improve our products and create more choices for consumers. If you want to create your space, We are an ideal choice. Always.
In case of windy weather, please do not stand in the gazebo. Please do not stand under the gazebo in case of heavy snowfall. For safety, please use expansion screws to reinforce the posts to the ground. In windy weather, please tighten the fence and netting to avoid tearing in high winds. In extreme weather conditions, you can use a rope to pull the four corners of the gazebo to keep it stable. Please clear the snow off the roof in time for the heavy snowfall. Make sure all screws are tightened before use.
EQUIPMENT REQUIREED(Not included in boxes) *NOTE:Tools / equipment are not shown to actual size and scale. LEVEL RUBBER MALLET PHILLIPS SCREW DRILL ALLEN KEY EQUIPMENT REQUIREED(Not included in boxes) *NOTE:Equipment are not shown to actual size and scale. SAFETY HAT SAFETY GOGGLES GLOVES STEPLADDER (6.
PARTS A B 4 PCS B1 2 PCS B2 2 PCS B3 2 PCS C 2 PCS C1 2 PCS C2 2 PCS C3 2 PCS D 2 PCS D1 2 PCS D2 2 PCS E 2 PCS E1 2 PCS 2 PCS
PARTS F E2 2 PCS G 4 PCS H 4 PCS H1 4 PCS J1 4 PCS J2 4 PCS K 4 PCS K1 4 PCS L 1 PC M 4 PCS M1 4 PCS N 4 PCS N1 4 PCS 4 PCS
PARTS P P1 2 PCS Q1 2 PCS Q2 2 PCS Q3 2 PCS Q4 2 PCS R 2 PCS R1 8 PCS S 2 PCS T 136 PCS T1 2 PCS T2 2 PCS U1 2 PCS U2 4 PCS 4 PCS
PARTS U6 U3 4 PCS 4 PCS Z U7 6 PCS Z1 16 PCS 72 PCS
PARTS V1 T1 V2 2 PCS 2 PCS W1 W2 2 PCS X1 T1 2 PCS V3 2 PCS 2 PCS V4 V5 2 PCS 8 PCS W3 W4 W5 2 PCS 2 PCS 2 PCS X2 X3 X4 2 PCS 2 PCS 2 PCS X5 2 PCS X6 2 PCS V6 V7 2 PCS 2 PCS W6 W7 W8 2 PCS 2 PCS 2 PCS X7 2 PCS Y Ya 4 PCS 4 PCS T1 X8 2 PCS X9 2 PCS X10 2 PCS
HARDWARE 1# M6x16mm 2# M6x23mm 261 PCS 3# 32 PCS 4# 16 PCS 5# M6x23mm 128 PCS 6# M6x47mm 84 PCS 9# 40 PCS 10# ST4.
1 Place part "A" on top of part "L" and use 3 screws "1#" for reinforcement. A 4 L 4 1# 12 Notice: Repeat the above steps to complete the connection of the remaining 3 pairs of components.
2 Attach part "F" to part "B" and part "C" and secure it with four "1#" screws to the lower edge of part "B/C". F B C B C 1# 1# F Notice: Repeat the above steps to complete the installation of the other pair of components.
3 Place part "C2" and ”C3” on the top of the inside of part "C" and part "C1" on the bottom of the inside of part "C" and secure it with 12 "1#" screws. Place part "B2" and ”B3”on the top of the inside of part "B" and part "B1" on the bottom of the inside of part "B" and secure it with 12 "1#" screws. The locations of parts "B1/C1" ,"B2/C2"and”B3/C3” are shown in the following diagram.
4 Attach part "F" to part "D" and part "E" and secure it with four "1#" screws to the lower edge of part "D/E". D F E 1# 1# D E 1# 1# F Notice: Repeat the above steps to complete the installation of the remaining components.
5 Place part "E2" on the top of the inside of part "E" and part "E1" on the bottom of the inside of part "E" and secure it with 12 "1#" screws. Place part "D2" on the top of the inside of part "D" and part "D1" on the bottom of the inside of part "D" and secure it with 12 "1#" screws. The locations of parts "D1/E1" and "D2/E2" are shown in the following diagram. D D2 D1 E E2 E1 1# 1# D2/E2 D/E D2 E2 1# D1/E1 The locations of parts "D1/E1" and "D2/E2" are shown in the following diagram.
Place the left and right sides of part "D" and part "E" on the top of part "A", respectively, and use four "2#" screws to x part "D" and "E". D" and "E" on the inside of the part. 6 Place the left and right sides of part "D" and part "E" on the top of part "A". Secure part "D" and part "E" with four "2#" screws (on the inside). Use four "3#" screws to secure part "D" and part "E" (on the outside).
7 Place the left and right sides of part "E" and part "D" on the top of part "A", and secure the inner side with eight "2#" screws and the outer side with eight "3#" screws.
8 Place part "J1" on the right side of the top of part "A" and secure it with 16 "1#" screws. Place part "J2" on the left side of the top of part "A" and secure it with 16 "1#" screws.
9 Place part "G" in the four corners and secure it with 16 "9#" screws. Place part "H" in the position shown and secure the top of part "H" with eight "9#" screws.
10 Use 8 "2#" screws to connect part "M" to part "M1". M M 2# M1 M1 Notice: Repeat the above steps to complete the connection of the remaining 3 groups of part "M" and part "M1".
11 Place four parts "M" on both sides of part "K", using eight "1#" screws.
12 Place the roof frame from the inside of the gazebo and install it with the frame on one side rst and the frame on the other side later. Attach the bottom of part "M1" to the top of part "A", using four "1#" screws.
13 The positions of part "N" and part "N1" are shown in the gure below. Use 16 "1#" screws to attach part "N", part "N1" to the bottom frame. N1 N1 N K N1 1# N N N N1 N1 N1 N N N1 N1 N N N 1# N N1 N1 1# N1 1# N 2 N1 4 1# 24 Attach part "N", part "N1" to the top frame using eight "1#" screws.
14 The positions of part "P", part "Q1" and part "Q2" are shown below. Use six "1#" screws to secure part "P", part "Q1" and part "Q2", and place part "R" in the four corners, using the "1#" screws. 1# Q1 R Q2 P P Q2 Q1 M1 P 1# Q2 Q1 Q2 Notice: Do not tighten the "1#" screw, tighten it after you have nished installing the roof.
15 The location of part”T” ,part "T1" and part "T2" is shown below. Install part "T1" and part "T2" with ten "1#" screws, install part "R1" to the connection of part "T1" and part "T2", and place part "R" at the four corners. T2 R1 T1 R R R R T1 T2 R1 R 1# 1# 1# Notice: Do not tighten the "1#"screw on part”R”, tighten it after you have nished installing the roof.
Diagram of the location of the small roof tiles Z1 Z1 V2 V1 Installation Tips:Part "Z" and part "Z1" serve to shield the sun and water. It may not be easy to install, so if it is not easy to install, you can remove it.
17 The positions of part "V3", part "V4", part "V5", part "V6" and part "V7" are shown below. Installation Tips:Part "V3", part "V4", part "V5", part "V6" and part "V7" are added to the roof from left to right. Please make sure the holes are aligned.
18 Place part "K1" on the top of part "K". Use two "12#" screws to x the sides of part "K" and tighten the "13#" screws in the middle.
Place part "V1" and part "V2" on both sides and secure them with part "T", using six "1#" screws. R 1# 1# V1 T R T V2 1# 1# V2 R R V1 1# Notice: Loosening the "1#" screws in the four corners, install the part "T" and re-torque it in.
20 Loosen the four corner parts "R" and four screws "1#", and place the parts "V1" and "V2" on both sides of the roof. Insert part "T", place part "R" and x it with 6 screws "1#".
22 The locations of part "U1", part "U2" and part "U3" are shown in the diagram below. Place part "U6" at the four corners and secure it to part "M1" with four "1#" screws. Place the part "U7" in the remaining position and secure it with 8 "1#" screws. U2 U3 U3 U2 U1 U1 U2 U3 U3 U1 U1 4 U6 4 U1 U2 4 U7 8 U3 4 1# 36 U2 M1 U6 U7 1# 1# Notice: The side where the short hole of the part is placed close to this side.
The positions of part "W1", part "W2", part "W3", part "W4", part "W5", part "W6", part "W7", and part "W8" are shown below. 2 2 W4 2 2 W1 Z W2 Z W3 Z 2 2 2 2 W2 W3 W4 W5 W6 W7 W8 W5 32 Z Z W6 Z W7 Z W8 Notice: The main function of the component "Z" is to block the entry of sunlight and water.To facilitate installation, the part "Z" can be removed, which will sacri ce a certain amount of sun and rain protection.
The positions of parts "X1", "X2", "X3", "X4", "X5", "X6", "X7", "X8", "X9", "X10", are shown below. X7 28 2 X6 2 2 X4 2 2 2 Z1 X1 Z X2 Z X3 2 X3 X4 X5 2 X6 X5 2 X7 X8 X9 X10 2 Z X8 Z 8 Z1 X9 Z X10 Z1 Notice: The main function of part "Z" and part "Z1" is to block the entry of sunlight and water.For ease of installation, part "Z" and part "Z1" can be removed, which will sacri ce a certain degree of protection from the sun and rain.
The positions of part "W1", part "W2", part "W3", part "W4", part "W5", part "W6", part "W7", and part "W8" are shown below. 25 The positions of part "X1", part "X2", part "X3", part "X4", part "X5", part "X6", part "X7", part "X8", part "X9", part "X10" are shown below. X9 X10 W1 W2 W3 W4 W5 W8 W7 W6 W5 W4 W3 W2 W1 X10 X9 X8 X1 X7 X2 X6 X3 X5 X4 X4 X5 X3 X6 X2 X7 X1 X8 W8 W7 W6 Notice: Install the parts in order from left to right.
26 Installation Tips: Roofs are installed from left to right. Place the part "S" under the circle in the gure Please do not tighten the screws during installation, and tighten them after nishing the installation. 1 2 3 1 3 2 3 4 1 1 4 1 4 4 6# 3 7# 2 S 10# S S In the position "1" in the picture, use eight "6#" screws to x. In the position "3" in the picture, use forty-four "6#" screws to x. In position "2" in the gure, use four "10#" screws to x.
27 The positions of part "P1", part "Q3", part "Q4"are shown below. Q3 P1 Q4 P1 P1 Loosen the "1#" screw and place the part "P1" in the position shown in the gure, and x it with two "11#" screws. 11# 11# 1# Loosen Q3 Q4 1# 11# 1# 11# 1# 11# 11# Loosen the "1#" screw, place part "Q3", part "Q4" in the position shown, and use 8 Use 8 screws "11#" and 3 screws "1#" to x them.
28 After installa part “4#”,Place 6 parts "H1" in the connection and use 6 "1#" screws to x them.
29 The positions of part "Ya" are shown in the gure below Place part "Ya"on the inside of the track. Ya Ya Ya Ya 4# Place part "Ya" in the inner hook.
30 The position of part "Y" is shown in the following diagram. Place part "Y" on the outside of the track. Connect the curtain hooks to the middle holes of the four corner posts. Y Y Y 4# Place part "Y" in the outer hook.
31 Use twenty "14#" screws to x the gazebo to the ground 14# 14# 1 2 3
1.To avoid blowing the gazebo over in windy weather, please use a rope to pull at the four corners. 2.If you encounter high winds during use, you can place a heavy object in the hole at the bottom of the curtain to prevent it from uttering. 3.Leakage may be encountered at the junction of the eaves, please use glass glue for bonding. 4.During heavy snowfall, please clear the snow from the roof in time to prevent it from bending.
If you have any issues with your item please let us know! We will always do our best to come up with a solution that you will be happy with. Please get in touch with our customer service team before returning the product. And pls do not throw the original box(es) if you have not nished assembling or con rmed no quality issues. Length of return period: Items can be returned within 30 days of purchase. In the meanwhile, everything you purchased from us comes with a one-year warranty.