TDS

ManualsBrandsSika ManualsKitchen10.1 fl. oz. AnchorFix-2 Anchoring Adhesive

PRODUCT DATA SHEET

Sika® AnchorFix-2

SUPER STRENGTH, TWO COMPONENT ADHESIVE ANCHORING SYSTEM

PRODUCT DESCRIPTION

Sika® AnchorFix-2 adhesive anchor system is

solvent/styrene free, epoxy acrylate based, and has been

specifically formulated as a high performance, two com-

ponent adhesive anchor system for threaded bars in un-

cracked concrete.

USES

Sika® AnchorFix-2 may only be used by experienced pro-

fessionals.

As a fast curing anchoring adhesive for all grades of:

Rebars / reinforcing steel▪

Threaded rods▪

Bolts and special fastening systems▪

In the following substrates:

Concrete▪

Solid masonry▪

Steel▪

Hard natural stone

▪

Solid rock

▪

* These substrates may vary greatly, in particular with regard to strength, com-

position and porosity. Therefore, for each application the suitability of Sika® An-

chorFix-2 Adhesive must be tested by first applying the Product only to a sample

area. Check in particular bond strength, surface staining and discoloration.

CHARACTERISTICS / ADVANTAGES

Fast curing▪

Standard guns can be used▪

High load capacity▪

Drinking Water certified▪

Non-sag, even overhead▪

Styrene-free epoxy acrylate▪

Low wastage▪

Fixing close to free edges.▪

Versatile range of embedment depths.▪

Anchoring without expansion forces.▪

APPROVALS / STANDARDS

EESR to AC308 by ICC-ES PENDING.▪

ESR to AC308 by IAPMO-UES.▪

Certified to ANSI / NSF - 61 by UL.▪

PRODUCT INFORMATION

Packaging

10 fl.oz. (299 ml) cartridge

Shelf Life

12 months from date of production

All Sika® AnchorFix-2 cartridges have the expiry date printed on the label.

Storage Conditions

Cartridges should be stored in their original packaging, the correct way up, in

cool conditions 41 °F to 77 °F (5 °C to 25 °C) out of direct sunlight.

Product Data Sheet

Sika® AnchorFix-2

November 2018, Version 01.03

020205010020000001

1 /

Summary of content (8 pages)

PAGE 1
PRODUCT DATA SHEET Sika® AnchorFix-2 SUPER STRENGTH, TWO COMPONENT ADHESIVE ANCHORING SYSTEM PRODUCT DESCRIPTION CHARACTERISTICS / ADVANTAGES Sika® AnchorFix-2 adhesive anchor system is solvent/styrene free, epoxy acrylate based, and has been specifically formulated as a high performance, two component adhesive anchor system for threaded bars in uncracked concrete.
PAGE 2
TECHNICAL INFORMATION Tensile Adhesion Strength 1. The above values represent mean ultimate values and allowable working loads. The allowable working loads have been reduced using a safety factor of 4.0 for tension and 3.0 for shear, however, in some cases, such as life safety, safety factors of 10.0 or higher may be necessary. 2. Allowable loads must be checked against steel capacity. The lowest value controls. 3.
PAGE 3
Design Considerations Allowable Tension, Nall = 0.33 x fu x nominal cross sectional area Allowable Shear, Vall = 0.17 x fu x nominal cross section area *The design professional on the job is ultimately responsible for the interpretation of the data provided above. Tension = 0.33 x fu x nominal cross sectional area Shear = 0.17 x fu x nominal cross section area *The design professional on the job is ultimately responsible for the interpretation of the data provided above.
PAGE 4
SYSTEM INFORMATION System Structure *The design professional on the job is ultimately responsible for the interpretation of the data provided above. APPLICATION INFORMATION Mixing Ratio Component A : component B = 10 : 1 by volume Coverage *Number of fixings assumes 30ml wastage in initial extrusion and holes filled to 3/4 full Product Data Sheet Sika® AnchorFix-2 November 2018, Version 01.
PAGE 5
Sag Flow Non-sag, even overhead Product Temperature Sika® AnchorFix-2 must be at a temperature of between 41 °F (5 °C) to 68 °F (20 °C) for application. Dew Point ▪ Beware of condensation. ▪ Beware of frost.
PAGE 6
APPLICATION INSTRUCTIONS MIXING SUBSTRATE QUALITY Getting the cartridge ready 1. Unscrew the cap Mortar and concrete must be older than 28 days. Substrate strength (concrete, masonry, natural stone) must be verified. Pull-out tests must be carried out if the substrate strength is unknown. The anchor hole must always be clean, dry, free from oil and grease etc. Loose particles must be removed from the holes.
PAGE 7
Pump approx. twice until both parts come out uniformly. Do not use this material. Release the gun pressure and clean the cartridge opening with a cloth. APPLICATION METHOD / TOOLS Anchors in solid masonry/concrete: Drilling of hole with an electric drill to the diameter and depth required. Drill hole diameter must be in accordance with anchor size. Inject the adhesive into the hole, starting from the bottom, while slowly drawing back the static mixer.In any case avoid entrapping air.
PAGE 8
BASIS OF PRODUCT DATA LEGAL DISCLAIMER Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions. • KEEP CONTAINER TIGHTLY CLOSED • KEEP OUT OF REACH OF CHILDREN • NOT FOR INTERNAL CONSUMPTION • FOR INDUSTRIAL USE ONLY • FOR PROFESSIONAL USE ONLY OTHER RESTRICTIONS See Legal Disclaimer.