Product Data Sheet

ManualsBrandsSika ManualsKitchen10.1 fl. oz. AnchorFix-2 Anchoring Adhesive

Product Data Sheet

Sika AnchorFix®-1

March 2020, Version 02.02

020205010010000001

PRODUCT DATA SHEET

Sika AnchorFix®-1

HIGH STRENGTH, TWO COMPONENT ADHESIVE ANCHORING SYSTEM

PRODUCT DESCRIPTION

Sika AnchorFix®-1 adhesive anchoring system has been

specially formulated as a high-performance, two

component adhesive anchor system for threaded and

reinforcing bars in uncracked concrete.

USES

As a fast curing anchoring adhesive for all grades of:

Rebars / reinforcing steel▪

Threaded rods▪

Bolts and special fastening systems▪

Can be used on:

Uncracked Concrete▪

Solid masonry▪

Hard natural stone

▪

Solid rock

▪

* These substrates may vary greatly, in particular with regard

to strength, composition and porosity. Therefore, for each

application the suitability of Sika AnchorFix®-1 Adhesive must

be tested by first applying Sika AnchorFix®-1 Adhesive only to a

sample area. Check in particular bond strength, surface

staining and discoloration.

CHARACTERISTICS / ADVANTAGES

Fast curing▪

Standard guns can be used▪

Can be used at low temperatures▪

High load capacity▪

Non-sag, even overhead▪

Styrene-free polyester resin▪

Low wastage▪

APPROVALS / STANDARDS

European Technical Approval (ETA) according to

ETAG001-5 for threaded bars only.

▪

1 /

Summary of content (8 pages)

PAGE 1
PRODUCT DATA SHEET Sika AnchorFix®-1 HIGH STRENGTH, TWO COMPONENT ADHESIVE ANCHORING SYSTEM PRODUCT DESCRIPTION CHARACTERISTICS / ADVANTAGES Sika AnchorFix®-1 adhesive anchoring system has been specially formulated as a high-performance, two component adhesive anchor system for threaded and reinforcing bars in uncracked concrete.
PAGE 2
PRODUCT INFORMATION Packaging 10.1 fl.oz. (299 ml) Shelf Life 12 months from date of production All Sika AnchorFix®-1 cartridges have the expiry date printed on the label. Storage Conditions Cartridges should be stored in their original packaging, the correct way up, in cool conditions 41 °F to 77 °F (5 °C to 25 °C) out of direct sunlight. TECHNICAL INFORMATION Tensile Adhesion Strength 1. The above values represent mean ultimate values and allowable working loads.
PAGE 3
Allowable Tension, Nall = 0.33 x fu x nominal cross sectional area Allowable Shear, Vall = 0.17 x fu x nominal cross section area *The design professional on the job is ultimately responsible for the interpretation of the data provided above. Tension = 0.33 x fu x nominal cross sectional area Shear = 0.17 x fu x nominal cross section area The design professional on the job is ultimately responsible for the interpretation of the data provided above.
PAGE 4
SYSTEM INFORMATION System Structure *The design professional on the job is ultimately responsible for the interpretation of the data provided above. APPLICATION INFORMATION Mixing Ratio Component A : component B = 10 : 1 by volume Coverage *Number of fixings assumes 30ml wastage in initial extrusion and holes filled to 3/4 full Product Data Sheet Sika AnchorFix®-1 March 2020, Version 02.
PAGE 5
Sag Flow Non-sag, even overhead Product Temperature Sika AnchorFix®-1 must be at a temperature of between 41 °F (5 °C) and 104 °F (40 °C) for application. Dew Point ▪ Beware of condensation. ▪ Beware of frost.
PAGE 6
APPLICATION INSTRUCTIONS SUBSTRATE QUALITY ▪ Mortar and concrete must be at the required strength. No need to be 28 days old. ▪ Substrate strength (concrete, masonry, natural stone) must be verified. ▪ Pull-out tests must be carried out if the substrate strength is unknown. ▪ The anchor hole must always be clean, dry, free from oil and grease etc. ▪ Loose particles must be removed from the holes.
PAGE 7
APPLICATION METHOD / TOOLS Anchors in solid masonry / concrete Drilling of hole with an electric drill to the diameter and depth required. Drill hole diameter must be in accordance with anchor size. The drill hole must be cleaned with a blow pump or by compressed air, starting from the bottom of the hole. (at least 2x) Important: use oil-free compressors. The drill hole must be thoroughly cleaned with the special steel brush (brush at least 2x).
PAGE 8
BASIS OF PRODUCT DATA LEGAL DISCLAIMER Results may differ based upon statistical variations depending upon mixing methods and equipment, temperature, application methods, test methods, actual site conditions and curing conditions. • KEEP CONTAINER TIGHTLY CLOSED • KEEP OUT OF REACH OF CHILDREN • NOT FOR INTERNAL CONSUMPTION • FOR INDUSTRIAL USE ONLY • FOR PROFESSIONAL USE ONLY OTHER RESTRICTIONS See Legal Disclaimer.