Installation Sheet

ManualsBrandsSignature Hardware ManualsShop All Signature HardwareSignature Hardware Quen 72" Wood Double Vanity Cabinet - Choose Your Vanity Top and Sink Configuration

1Vanity Installation Guide

1. Determine your vanity placement and mark the area on the wall

where it will be installed.

2. Locate and mark the location of the studs to which you will fasten

your vanity. You can nd studs by listening for a solid sound as you

knock on the wall or by using a stud nder.

Tip: If the studs in your bathroom do not line up to the mounting

location for your vanity, wood blocking can be installed between the

studs using standard 2 x 4’s. If wood blocking needs to be installed

behind the nished wall, we recommend consulting a professional

if you are unfamiliar with this type of installation.

3. If your vanity cabinet has a solid back, mark and drill holes to

accommodate drain pipes and supply pipes as necessary.

VANITY INSTALLATION GUIDE

Unpack the vanity and inspect product for any shipping damages. If you nd damages, do not install. Contact Customer

Service at 1.866.855.2284.

We recommend consulting professional help if you are unfamiliar with installing bathroom vanities and/or plumbing.

Signature Hardware accepts no liability for any damage to the vanity, counter top, faucet, wall, plumbing or for personal

injury during installation.

TOOLS AND MATERIALS:

VANITY INSTALLATION

Pencil Stud Finder Tape Measure

Drill Screwdriver Level

Silicone Sealant Wooden Shims

Damp Cloth

wall studs

mounting

rail

screws screws

4. Place the vanity in the installation location. Verify that the vanity cabinet is level. If the vanity is not level, use vanity

feet (if included) or wooden shims to adjust as necessary.

5. Attach the vanity to the wall by screwing through the mounting rail in the back of the vanity cabinet into the wall

studs.

Note: For under-mount sinks, go to “Sink Installation Instructions” below before continuing to step 6.

6. Install the integral sink/vanity top by applying a dot of silicone sealant on the corners of the vanity. Position the

vanity top onto the vanity and press rmly into place. Wipe away any excess sealant with a damp cloth.

7. If your vanity top has a separate side and/or back-splash, place a bead of adhesive silicone sealant on the back

and press rmly into place.

8. Fill any gaps between the wall and splash, and vanity top and splash with silicone sealant. Wipe away excess

sealant with a damp cloth.

Summary of content (4 pages)

PAGE 1
VANITY INSTALLATION GUIDE Unpack the vanity and inspect product for any shipping damages. If you find damages, do not install. Contact Customer Service at 1.866.855.2284. We recommend consulting professional help if you are unfamiliar with installing bathroom vanities and/or plumbing. Signature Hardware accepts no liability for any damage to the vanity, counter top, faucet, wall, plumbing or for personal injury during installation.
PAGE 2
VANITY TOP INSTALLATION Important: If the vanity top weighs 50 lbs. or more, have someone assist you. Silicone Adhesive 1. Lift the vanity top from the front edge, bringing to a vertical position, while keeping the back edge in the box. 2. Remove the vanity top from the box while maintaining its vertical position. You can use the sink openings to hold vanity top, but be sure to also the top from the bottom. Always maintain the top in a vertical position while carrying. 3.
PAGE 3
SINK INSTALLATION UNDERMOUNT SINK INSTALLATION 1. Carefully turn the counter top over, resting it on a soft, stable surface to prevent damage. 2. Position the undermount sink over the sink cutout on the counter top. Make sure the sink is centered with the faucet hole and is evenly spaced between the bolt holes. 3. Draw an outline of the sink on the counter top. 4. Remove the sink from the counter top. Apply a generous bead of silicone sealant around the perimeter of the sink rim. 5.
PAGE 4
VESSEL SINK INSTALLATION 1. Carefully place the sink upside down on the counter top. Apply a continuous bead of silicone sealant to the base of the sink where it will rest on the counter. 2. Turn the sink right-side-up and position over the 2" drain hole. 3. If desired, apply a continuous bead of silicone sealant around the perimeter of the sink base for additional stability. 4. Remove any excess sealant and let dry for 24 hours.