INSTRUCTION MANUAL Empressa Digital Steam Press SSP-3208
CONTENTS Features of the Digital Steam Press..............................1 Safety Reminders......................................................2 Part Identification...................................................3-4 Steam Press Operation Preparation for use......................................................5 Filling the water tank...................................................5 Turning on the power...................................................5 Selecting the temperature...................
Features of the Digital Steam Press Ø Your Steam Press provides clean, professional results every time! Ø The pressing surface is seven times larger than most hand-held irons. Ø Reduces ironing time by up to 50%. Ø Multiple dry-heat and steam settings for all types of fabric. Ø Burst setting removes stubborn wrinkles. Ø Variable temperature selection. Ø Automatic shut-off safety feature while open or closed with audible alert. Ø Over 100lbs. of even pressure ensures sharp, long lasting creases.
SAFETY REMINDERS WARNING Read all of the instructions and then save them for future reference. Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø Ø To protect against the risk of electric shock, do not immerse the appliance in water. Do not let the cord hang over the edge of counters. Do not allow the cord to touch hot surfaces. Always allow the appliance to cool for at least thirty minutes before storing. Always put the appliance in a secure place on a table or counter when using.
PART IDENTIFICATION 1. The Pressing Handle raises and lowers the Pressing Plate. By lowering the Pressing Handle until it reaches the lowest point possible you automatically obtain maximum pressure. 2. The Locking Knob will lock together the Pressing Plate and Ironing Board. Turn the Locking Knob to the locked position to carry or store the Steam Press. 3. The Grey Steam Burst Button on the handle grip produces a burst of steam when pressed. 4.
13. The Pressing Cushion is a fabric covered pad used for pressing gathered or contoured areas such as sleeves, darts, and yokes. 14. A plastic water Spray Bottle is used for dampening fabric before pressing. 15. A Water Container is used for filling the Water Tank. The following information is provided for service by a qualified electrician only: Rated voltage: 120V, 60Hz, 1350W WARNING: This appliance must be grounded. Use only the proper type outlet when plugging in the appliance.
STEAM PRESS OPERATION STEP1 - PREPARATION FOR USE Set the appliance on a sturdy work surface. Unlock the Locking Knob. STEP 2 - FILLING THE WATER TANK BEFORE PLUGGING IN THE APPLIANCE, fill the water tank; a. Always make sure the appliance is unplugged before filling the tank. b. Fill the Water Tank with the Pressing Plate lifted to the raised (up) position. Slide the Water Tank towards the front of the unit. It will not come completely out so do not force it to do so.
STEP 4 SELECTING THE TEMPERATURE Press the [ SELECT ] arrow buttons to choose the kind of fabric you wish to press. Press to move selection to higher setting and press to move selection to lower setting. a. Examine the garment label if unsure and look up the type on the chart.
STEP 5 - STEAM CONTROL IMPORTANT NOTE: Steam is produced only when the Yellow Steam Ready light is on. The Green Ready Light goes off when the unit has reached the desired temperature. The Yellow Steam Ready Light will come on when the unit is ready to produce steam. IMPORTANT NOTE: If this is the first time you are using the Steam Press or you have been storing it for some time, lift the Pressing plate into the raised position and press the Steam Burst Button several times until the steam begins to flow.
STEP 6 - PRESSING a. Lift the Pressing Handle (A). The Pressing Plate (B) moves to the up position. b. Carefully arrange the garment to be pressed onto the Ironing Board (C). c. Grasp the handle of the Pressing Plate(A) and lower it onto the Ironing Board (C), capturing the garment between the two halves of the Steam Press. For light duty Pressing, simply lowering the handle and allowing the Pressing Plate to rest on the Ironing Board will be sufficient. Return to the open position.
STEP 7 - FINISHING PRESSING/STORING THE UNIT a. Water may be left in the reservoir, because it will not drip out if the machine is stored in an upright position. However, it is recommended that if the machine will be stored for some time, that all the water in the unit should be drained by pressing the Steam Burst Button until all of the water is pumped out. b. Press the [ POWER ] button, the Red Power Light will go out. Disconnect the plug from the outlet. Leave appliance in open position. c.
STEP 8 - CLEANING (As needed) a. Cleaning the Pressing Plate: Place the Pressing Cushion in the center of the Ironing Board. Place a clean towel over the Pressing Cushion and the Ironing Board. Set the Steam Control and Temperature Control to their maximum setting. When the Ready Light comes on, gently lower the Pressing Plate onto the Pressing Cushion. With water in the reservoir tank, press the Steam Burst Control 6 to 7 times.
SUGGESTIONS FOR SUCCESS -USING PRESS CLOTH: Placing a press cloth ( a piece of clean fabric) between the fabric and the Pressing Plate may be desirable, especially for more delicate fabrics. OLDER STYLE BUTTONS AND ZIPPERS: While most modern buttons and zippers require no special attention, some older types may be heat sensitive. Take care with items that could melt. Lower the heat or steam settings, place the items FACE DOWN on the ironing board, and cover the fabric with a press cloth BEFORE pressing.
USE OF THE PRESSING CUSHION -Some garments have been constructed with details, such as darts, curved Seams and shoulder pads, which are not intended to be pressed flat. A Pressing Cushion is supplied with your Steam Press for use with These areas. a. Use the cushion whenever pressing areas where no creases are desired or to shape tailored garments. b. Place the area to be pressed onto the Ironing Board. c. Place the Pressing Cushion under the dart, seam etc. d.
TECHNIQUES FOR PRESSING -LARGE PIECES OF FABRIC: To press large pieces of fabric, place the entire piece in the storage area behind the Ironing Board. The area you want to press first is on the top of the pile. Pull the fabric towards you, over the Ironing Board and lower the Pressing Plate, pressing each section as you move the fabric forward. Allowing the pressed fabric to drape in front of the Pressing Plate will Preserve the Pressing and give you a complete job free of wrinkles. SHIRTS AND BLOUSES: a.
PANTS: a. Place the pressing Cushion under the waistband and press. b. Reposition the waistband and continue around the pants until the entire waistband is pressed. c. To press the in seam, place the Pressing Cushion under the area to be pressed. Press the entire in seam and repeat for the other leg. d. Press the front and back pleats using the same method. Fold one leg along the creased line. Place it on the Ironing Board so that the seams will not be pressed. Press the crease. PLEATED SKIRTS: a.
TROUBLE SHOOTING Below is a chart detailing the most common problems, their causes and solutions. Before shipping any appliance to a service center please check to make sure that the solution is not listed here: PROBLEM CAUSE SOLUTION Steam Press cannot be opened using Pressing Handle. Locking Knob is in Locked position. Turn the Locking Knob to the unlocked position. Steam Press becomes warm but Does not remove wrinkles. Temperature Setting is not high enough for the fabric attempted.
PROBLEM CAUSE SOLUTION No Steam. Water Level is too low. Controls have not been properly set. Fill the water tank. If suitable for the fabric, make a selection to a higher temperature. Wait for the Steam Ready Light to come on. If not use spray misting bottle as directed. Water drips from the Pressing Plate. Steam Button has been pressed too long. The Pressing Handle will not move into the Automatic Maximum pressure position. Item on the Ironing Board is too thick to use this pressure.
ONE YEAR LIMITED WARRANTY Warranty: This product warranty extends only to the original consumer purchaser of the product. This product is warranted by the manufacturer to be free from all defects in materials or workmanship for a period of one year from the date of original purchase. This warranty is subject to the following conditions, exclusions and exceptions.
Consumer Service will give you further instructions for returning a defective product for repair or replacement. When returning a defective product, carefully pack the item to avoid damage in shipping. the manufacturer cannot assume responsibility for loss or damage during incoming shipment. We recommend that you insure the package, as damage in shipping including the shipping cost is not covered by this warranty.
