User Manual

ManualsBrandsSiemens ManualsFire - Addressable Stand-alone PanelsRDM-MXL Remote Diagnostics Module, Installation Instructions

P/N 315-096325-4

INTRODUCTION

The Model RDM-MXL module (RDM for

connection to the MXL PIM-1) from Siemens

Industry, Inc., as shown in Figure 1, connects

the MXL to a remote location via a telephone

line. The module is designed to be installed

and serviced by fully qualified field engineers.

There are no user-serviceable or installation

parts inside the unit.

NOTE:

The minimum revisions required to operate the

RDM-MXL are listed below:

• MKB firmware Revision 7.0

• CSG-M Revision 7.0

• MXL Revision 7.2

• MXL-IQ Revision 2.0

The following items are supplied with the

RDM-MXL:

YTITNAUQMETI

1noitcennoC1-MIPLXMrof1-MDR

)eludoMscitsongaiDetomeR(

1tekcarBgnitnuoM

4swercSenihcaM4M

4srehsaWta

1LXM-MDRrofrotcennocrewoP

1LXM-MDRrofrotcennocyalernoisivrepuS

1leballavorppaCCFlanoitiddA

The user will need to supply the following items:

YTITNAUQMETI

1rof1-MDRotyrettaBdnaLXMmorfelbaC

1-MIPLXM

1rof1-MDRot1-MIPmorfelbaCecafretnI

)noitamrofnigniri

weeS(1-MIPLXM

1enohpeleT11JRtnailpmoC86traPCCF

droC

1)088296-005N/P(etalPretpadAOFPM-LXM

1eludoMgnitimiLrewo

P53-MLP

)094398-005N/P(

Figure 1

MXL-RDM Module General Configuration

Installation Instructions

Model RDM-MXL

Remote Diagnostics Module

Siemens Industry, Inc.

Building Technologies Division

Florham Park, NJ

Siemens Building Technologies, Ltd.

Fire Safety & Security Products

2 Kenview Boulevard

Brampton, Ontario

L6T 5E4 Canada

Summary of content (12 pages)

PAGE 1
Installation Instructions Model RDM-MXL Remote Diagnostics Module INTRODUCTION The user will need to supply the following items: The Model RDM-MXL module (RDM for connection to the MXL PIM-1) from Siemens Industry, Inc., as shown in Figure 1, connects the MXL to a remote location via a telephone line. The module is designed to be installed and serviced by fully qualified field engineers. There are no user-serviceable or installation parts inside the unit.
PAGE 2
as the MOM-4 and can accommodate 2 RMDMXL modules. An assembly kit is included with the bracket that contains four nuts and eight screws. Mount the bracket in the enclosure with four nuts at the positions labeled “X” in Figure 2. Refer to Figure 3 for wiring in the MXL/MXLV enclosure. POWER REQUIREMENTS Typical: 150mA at 24 VDC Voltage Input: 20-30 VDC NOTE: Be sure to include the RDM-MXL in battery calculations.
PAGE 3
Figure 3 Wiring the RDM-MXL in an MBR-2 or MME-3 Enclosure 3
PAGE 4
Figure 4 Connecting the RDM-MXL to the MXL/MXL-IQ System with MMB-2/SMB-2 Main Board Figure 5 Connecting the RDM-MXL to the MXL/MXL-IQ System with MMB-1/SMB-1 Main Board 4
PAGE 5
. For programming of RDM-1 for MXL PIM-1, a PC can be temporarily connected to Port 232A of RDM-1 for MXL PIM-1. Note that this is a straight-through standard RS-232 cable for laptops. RDM-1 for MXL PIM-1 RS-232 Port A (9 Pin-DCE) MXL VDT-132 (DB25) 25 Pins PC / LAPT OP (DB25-COMPORT ) 25 Pins PC / LAPT OP (DB9-COMPORT ) 9 Pin 2 3 3 2 3 2 2 3 4 20 20 4 5 7 7 5 Connecting to the Telephone Network 1. Connect the telephone line to the RJ11 phone socket on the RDM-MXL.
PAGE 6
corresponds to the password configured for your login name. The RDM-MXL is shipped with the highest level (level 1) password of PWORD1. After entering the correct password, the main menu will scroll on the screen (entering the incorrect password will exit the programming mode and revert the RDM-MXL to normal operating mode). Operation of LEDs: Each port has a green and a yellow LED. When the green LED is lit, it means the port is operating normally.
PAGE 7
• To back out of a menu (and return to the Main Menu) without saving any changes that were made, press the key or the (q) key. MXL. When failure occurs, the RDM will get no further events from the MXL. Relay Rating: 30V, 1A (resistive) 125 VAC, 0.250A (resistive) • The Main Menu is displayed after you type the correct password from the programming terminal or PC. Please note that the relays are not set to fail-safe mode.
PAGE 8
(6) (7) - (A) The terminal protocol should be set to XL Graphics or MXL VDT 132 if supervision to the terminal (Port A) is required during monitoring. Otherwise, set it to No Device if this port is going to be used for programming only. (3) - (6) The communications parameters for Dialup Connections between RDM-MXL and RDM-PC should not be changed unless explicitly required.
PAGE 9
disallow access to the system. The RDM-PC will indicate a logging error message when a login attempt is made. U.S.A. - FCC EQUIPMENT LIMITATIONS: • An FCC Part 68 compliant telephone cord must be used. Up to 8 login names can be programmed. Use the Prev and Next options to step through each login name. • This equipment complies with Part 68 and Part 15 of the FCC rules.
PAGE 10
INDUSTRY CANADA - EQUIPMENT ATTACHMENT LIMITATIONS: NOTICE: The Industry Canada label identifies certified equipment. This certification means that the equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.
PAGE 11
PAGE 12
Siemens Industry, Inc. Building Technologies Division Florham Park, NJ P/N 315-096325-4 Siemens Building Technologies, Ltd.