SIMATIC Industrial PC SIMATIC Industrial PC SIMATIC Panel PC 677B SIMATIC Industrial PC SIMATIC Panel PC 677B Operating Instructions 1 Preface ______________ 2 Safety ______________ 3 Description ______________ 4 Application planning ______________ 5 Mounting ______________ 6 Connecting ______________ Integration into an 7 ______________ automation system 8 Commissioning ______________ 9 Operation and configuration ______________ 10 Operation ______________ 11 Functions ______________ 12 Maintenance and s
Safety Guidelines Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger.
Table of contents 1 Preface ...................................................................................................................................................... 7 2 Safety ........................................................................................................................................................ 9 3 4 5 6 7 2.1 Safety guidelines............................................................................................................................
Table of contents 8 9 10 4 7.1 Overview ..................................................................................................................................... 47 7.2 7.2.1 7.2.2 Device in SIMATIC S7 network................................................................................................... 48 MPI/PROFIBUS-DP network....................................................................................................... 48 Connecting an S7 automation system ...............
Table of contents 11 12 Functions ................................................................................................................................................. 93 11.1 Overview ......................................................................................................................................93 11.2 Safecard on Motherboard (SOM).................................................................................................94 11.3 Temperature monitoring.........
Table of contents 13.3 14 15 16 17 6 BIOS beep codes ...................................................................................................................... 156 Troubleshooting/FAQs........................................................................................................................... 159 14.1 General problems...................................................................................................................... 159 14.
1 Preface Purpose of this manual These operating instructions contain all the information you need for commissioning and using the SIMATIC Panel PC 677B. It is intended both for programming and testing personnel who commission the device and connect it with other units (automation systems, programming devices), as well as for service and maintenance personnel who install add-ons or carry out fault/error analyses.
Preface Position in the information landscape The documentation for the Panel PC includes the following sections: ● SIMATIC Panel PC 677B, Operating Instructions (compact) with the following information: – Commissioning – Legal information ● SIMATIC Panel PC 677B, Operating Instructions The documentation is supplied with the Panel PC in electronic form as a PDF file on the "Documentation and Drivers" CD. The documentation is available in German, English, French, Italian, Spanish, and Chinese.
2 Safety 2.1 Safety guidelines Warning Emergencies In the event of a device fault, interrupt the power supply immediately. Inform the customer service personnel responsible. Malfunctions can occur when the operator controls or power cable are damaged or when liquids or foreign objects penetrate the device. Warning Following the results of a risk analysis, additional protection equipment on the machine or the system is necessary to avoid endangering persons.
Safety 2.1 Safety guidelines Electrical connection Warning Disconnect the device from the mains before every intervention. Do not touch power lines or data transmission lines during electrical storms and do not connect any cables. System expansions Only install system expansion devices designed for this device. If you install other expansions, you may damage the system or violate the safety requirements and regulations for radio frequency interference suppression.
Safety 2.1 Safety guidelines Handling and disposal of lithium batteries Warning Danger of explosion and the release of harmful substances! Do not throw lithium batteries into fire, do not solder onto the cell body, do not open, do not short circuit, do not reverse pole, do not heat above 100 °C, dispose of according to regulations, and protect from direct sunlight, moisture and condensation. Replace lithium batteries with the same brand or a brand recommended by the manufacturer.
Safety 2.2 General Information 2.2 General Information Overview Caution The device must only be operated in closed rooms. Failure to comply nullifies the warranty Operate the device only in acordance with the ambient conditions specified in the technical specifications. Protect the device against dust, moisture and heat. Do not place the device in direct sunlight. Transport Unpack the device at its installation location. Transport the device only in the original packaging.
Safety 2.2 General Information Tools & downloads Please check regularly if updates and hotfixes are available for download to your device. Downloads are available on the Internet at http://www.siemens.com/asis under "Support". Click "Overview of Panel PCs" under "Tools & Downloads". Using the global search function, you can then also search for any downloads you require. Optical drive Notice An optical drive should only be operated in a mechanically undisturbed environment without vibrations and shock.
Safety 2.2 General Information Sources of light Notice Position the screen so that it is not subject to direct sunlight or other strong sources of light. Defective pixels in the display At present, the manufacturing process of modern displays does not guarantee that all pixels of the display will be perfect. A small number of defective pixels in the display is therefore unavoidable. This does not present a functional problem as long as the defective pixels are not bunched in one location.
Safety 2.3 ESD directives 2.3 ESD directives What does ESD mean? Almost all electronic modules are equipped with highly integrated components and elements in MOS technology. For technological reasons, these electronic components are very sensitive to overvoltages and, consequently, to electrostatic discharge.
Safety 2.3 ESD directives Handling ESD modules As a rule: Only touch ESD components if unavoidable due to necessary tasks. Only touch the components when the following holds true: ● You are permanently grounded by means of an ESD armband. ● You are wearing ESD shoes or ESD shoes grounding protective strips in connection with ESD floors. Before you touch an electronic assembly, your body must be discharged. Touch a conductive object immediately beforehand, e.g.
3 Description 3.1 Panel PC 677B design Design Figure 3-1 Panel PC 677B (1) Computer unit (2) Control unit Product Brief The device is available with different control units which are distinguished by the size of the display and by the key or touch panel.
Description 3.1 Panel PC 677B design Key panel variants ● Color display with backlighting: – 12'' TFT technology with 800 x 600 resolution – 15'' TFT technology with 1024 x 768 resolution ● Membrane keyboard with alphanumeric keys, numeric keys, cursor keys and control keys ● Function keys and softkeys ● Integrated mouse ● LEDs for power supply, temperature, softkeys, and function keys and buttons ● Front-mounted USB 2.0 interface for connecting external I/O devices.
Description 3.2 Features 3.2 Features Basic data Design Panel mounting device, computer unit Processor • • • Intel ® Celeron M 440 1.86 GHz 533 MHz Front Side Bus (FSB), 1024 KB Second Level Cache Intel ® Core 2 Duo 1.66 GHz T5500 667 MHz Front Side Bus 2048 KB Second Level Cache Intel ® Core 2 Duo 2.
Description 3.
Description 3.3 Panel PC 677B accessories 3.3 Panel PC 677B accessories Accessories Comment Order No.
Description 3.
Application planning 4.1 4 Overview Introduction This section describes the first steps after unpackaging, the permitted mounting positions and the fixation. This section describes the necessary considerations for EMC. Field of application The Panel PC is an industry-standard PC platform for demanding tasks in the field of PCbased automation.
Application planning 4.2 Unpacking and checking the delivery 4.2 Unpacking and checking the delivery Procedure 1. Please check the packaging material for transport damage upon delivery. 2. If any transport damage is present at the time of delivery, lodge a complaint at the shipping company in charge. Have the shipper confirm the transport damage immediately. 3. Unpack the device. Caution Do not lie the device on its back. This will avoid any damage to an optical drive which may be present.
Application planning 4.3 Device identification data 4.3 Device identification data The device can be clearly identified with the help of this identification data in case of repairs or theft. Enter the following data in the table below: ● Serial number: The serial number (S VP...) is found on the rating plate.
Application planning 4.4 Mounting positions and fastening 4.4 Mounting positions and fastening 4.4.1 Installation guidelines Before installing the device, read the following general notes relating to installation. Warning Danger, high voltage Isolate the power supply to the switchgear cabinet before opening it. Ensure that the power to the switchgear cabinet cannot be turned on accidentally. Caution The device is approved for operation in closed rooms only.
Application planning 4.4 Mounting positions and fastening Note The computer unit with AC power supply satisfies fire protection requirements to EN 60950-1. It may therefore be installed without additional fire-proofing measures. ● Provide adequate volume in the switchgear cabinet for air circulation and heat transport. Keep at least 10 cm distance between the device and switchgear cabinet.
Application planning 4.4 Mounting positions and fastening 4.4.2 Permitted mounting positions Approval Only certain mounting positions are approved for the device. $ % Figure 4-1 Mounting position Table 4-1 Permissible deviations from the vertical mounting position Temperature Angle A Angle B to 45°C 20° 20° Note When mounting the device at an angle, note the following. • Do not subject the device to mechanical stress. • Operation of a DVD drive is not permitted. 4.4.
Application planning 4.4 Mounting positions and fastening 4.4.4 Protection against dust and water Principle With the relevant installation, the device is protected on the front agains the ingress of dust and water. The "degree of protection" is in accordance with IEC 60529: On the front, the device has degree of protection IP65, the rear of the operator section and the computer unit have degree of protection IP20.
Application planning 4.5 Mounting cut-out 4.5 Mounting cut-out 4.5.1 Preparing the mounting cut-out The following illustration shows the dimensions for the mounting cut-out.
Application planning 4.
Application planning 4.5 Mounting cut-out 4.5.2 Mounting depth of the device 7 Panel PC with operator control units Depth D Key panel with 12" TFT 105 mm Key panel with 15" TFT 124 mm Touch panel with 12" TFT 123 mm Touch panel with 15" TFT 121 mm Touch panel with 17" TFT 130 mm Touch panel with 19" TFT 130 mm Note Additional mounting depth with optical drive The installation depth increases by 21 mm when an optical drive is installed in the device.
Application planning 4.6 EMC Guideline 4.6 EMC Guideline Electromagnetic compatibility The device fulfills the requirements of the EMC law of the Federal Republic of Germany as well as the EMC directive of the Single European Market. The device is designed as a built-in device. You can ensure compliance with the EN 610004-2 (ESD) EMC standard by installing the device in grounded metal cabinets (for example, 8 MC cabinets, Siemens catalog NV21).
Application planning 4.
5 Mounting 5.1 Securing the device with clamps Requirement Accessories Display Clamp 12" 15" 17" 19" 6x 6x 8x 8x The clamps are provided with the control unit. Tool 2.5 mm hexagonal spanner Procedure Figure 5-1 Clamp assembly 1. Disconnect the device from the power supply. 2. Working from the front, insert the device into the 19" rack on the swivel arm or in the mounting cut-out. 3. Fasten the control unit from the rear using the clamps. 4. Tighten the setscrews to a torque of 0.4 - 0.
Mounting 5.1 Securing the device with clamps Notice Control cabinet installation: Material strength at the mounting cut-out Ensure that the material strength at the mounting cut-out is a minimum of 2 mm and a maximum of 6 mm. Please follow the specifications for the dimensions in the "Preparing the mounting cut-out" section.
Mounting 5.2 Securing with screws 5.2 Securing with screws Note Securing with screws is not possible with the 12" touch panel variant. To secure the 17" and 19" touch panel with screws, backing plates with order number 6AV7672-8KE00-0AA0 are required on the front. Drill holes in the control unit Steps for drilling holes 1 Drill holes (Ø approx. 2.5 mm) from the rear in the four recesses of the control unit 2 Drill these holes with a diameter of Ø 5.5 mm for M5 and a Ø 6.5 mm for M6.
Mounting 5.2 Securing with screws Drill holes in the mounting unit 1. Drill the holes at the prepared mounting cut-out according to the information for L3 and L4. (see Chapter "Mounting cut-out" ) 2. Working from the front, insert the device into the 19" rack on the swivel arm or in the mounting cut-out of the control cabinet. 3. Secure the control unit by inserting suitable screws and nuts IP54 degree of protection The IP54 degree of protection is guaranteed for mounting together with the ring seal.
6 Connecting 6.1 Connection elements and operator controls Connection and Operator Control Components of the Computer Unit Locations of connection and operator control components Pos Name Description (1) PCI (e) 2 slots for PCI expansion module (2) DVI/VGA DVI/VGA socket for CRT or LCD monitor with DVI interface or VGA monitor via DVI/VGA adapter (3) Compact Flash Slot for Compact Flash card (4) COM 1 Serial port (RS232) 9-pin D-sub connector (5) USB 4 USB 2.
Connecting 6.1 Connection elements and operator controls Notice On / Off switch The On / Off switch does not disconnect the device from the mains. When the switch is in the 0 position, the device is still connected to the auxiliary voltage. Connection components of the control unit USB connection control unit Pos Name Description (1) USB 1 connection USB 2.0 high current / 500 mA under sealed cover (not available with every product variant).
Connecting 6.2 Connecting the 120 V / 240 V Ac power supply 6.2 Connecting the 120 V / 240 V Ac power supply Note before connecting the device Note The varying voltage power supply module is designed for operation on 120 / 240 V AC networks. The setting of the voltage range takes place automatically. Warning Do not connect or disconnect power and data cables during thunderstorms.
Connecting 6.2 Connecting the 120 V / 240 V Ac power supply Note The power supply contains an active PFC (Power Factor Correction) circuit to conform to the EMC guidelines. Uninterruptible AC power systems (UPS) must supply a sinusoidal output voltage in the normal and buffered mode when used with SIMATIC PCs with an active PFC. UPS characteristics are described and classified in the standards EN 50091-3 and IEC 62040-3.
Connecting 6.2 Connecting the 120 V / 240 V Ac power supply Connecting How to connect the device to the 120 V AC / 240 V AC power supply 1 Ensure that the On/Off switch is in '0' position (Off) when you plug in the power cord in order to avoid unintentional startup of the device. 2 Connect the equipotential bonding. 3 Insert the power cable in the electrical socket. 4 Fasten the cable with the supplied power plug latch, if necessary.
Connecting 6.3 Connecting the (24 V) DC power supply 6.3 Connecting the (24 V) DC power supply Note before connecting the device Warning Only connect the device to 24 V DC power supply systems which meet the requirements of a safe extra-low voltage (SELV); in addition, a protective conductor must be connected. The conductors must withstand the short-circuit current of the 24 V DC power source, so that a short-circuit will not damage the cable. Only connect cables with a minimum crosssection of 1.
Connecting 6.4 Connecting the Equipotential Bonding Circuit 6.4 Connecting the Equipotential Bonding Circuit A low-resistance ground connection ensures that interference signals generated by external power supply cables, signal cables or cables to the I/O modules are safely discharged to ground.
Connecting 6.5 Connecting Ethernet strain relief 6.5 Connecting Ethernet strain relief The Ethernet strain relief provided in the package is used to prevent accidental removal of the Ethernet cable with Industrial EthernetFastConnect connector from the device. Two cable ties (not included in the package) are needed to use this accessory. To fix the Ethernet strain relief with Industrial EthernetFastConnect connector, you will need a TORX T20 screwdriver.
Integration into an automation system 7.1 7 Overview Introduction The following options are available for integrating the device in existing or planned system environments and networks. Ethernet The integrated Ethernet interface can be used for communication and for data exchange with automation devices such as SIMATIC S7. You require suitable software for this: STEP7, WinCC, WinCC flexible, WinAC, SIMATIC NET.
Integration into an automation system 7.2 Device in SIMATIC S7 network 7.2 Device in SIMATIC S7 network 7.2.1 MPI/PROFIBUS-DP network You can connect the device to a SIMATIC S7 automation system or a PROFIBUS DP network via the MPI/DP interface. You can connect up to 32 PC, PG, or AS devices to one network segment. The use of repeaters allows you to interconnect several MPI/PROFIBUS DP network segments. The complete MPI/PROFIBUS DP network consists of a maximum of 127 stations.
Integration into an automation system 7.3 Transferring authorizations Procedure 1. Disconnect the device from the mains. Caution Risk of damage to the device! Neutralize the static charge of your body, the device, and the connecting cables. You can do this by briefly touching the metal housing with the cable in your hand. 2. Insert the PROFIBUS cable in the MPI/DP socket. 3. Reconnect the device to the electrical power system. 7.3 Transferring authorizations Note The device has no floppy disk drive.
Integration into an automation system 7.
Commissioning 8.
Commissioning 8.2 Switching on the device 8.2 Switching on the device Procedure 1. Switch on the external AC or DC supply. 2. Connect the external keyboard and mouse. 3. Switch on the equipment using the switch next to the supply connector. 4. The "POWER" LED will light up: The device starts up and boots. Self-test After switching on, the device performs a self test. During the self test, the message "Press to enter SETUP" appears briefly. Do not press this key during this first start up.
Commissioning 8.3 Setting up the Microsoft Windows operating system 8.3 Setting up the Microsoft Windows operating system Introduction The setup wizard appears immediately following the startup of the device. The wizard is used to set the parameters of the operating system. Note The dialogs of the setup wizards differ slightly in some places for the Windows 2000 Professional and Windows XP Professional operating systems. In order to change to the next dialog, click on the ">>" button.
Commissioning 8.4 Additional applications 8.4 Additional applications First commissioning ● The "Panel Wizard" program is automatically started up once during first commissioning. ● The Panel Wizard implements the specific settings for the Panel PC during the initial start-up of the operating system. ● During the first start-up of the Panel PC, different dialogs appear on the screen based on which the drivers and applications can be set.
Commissioning 8.4 Additional applications Figure 8-2 8.4.1 Panel type Touch Panel set-up 1. Select the desired screen size. Note The screen size data can be found on the rating plate of the Touch Panel. The screen resolution is adapted accordingly.
Commissioning 8.4 Additional applications Note During the hardware recognition, the Touch Controller is detected again and entered. Figure 8-4 Touch Panel; exiting the Panel Wizard 2. Click on the button "Finish". A hardware detection symbol is displayed. Figure 8-5 Panel Wizard, hardware detection Note Soft keyboard • If the checkbox "enable" is activated, at every program start of MS Windows the Windows soft keyboard is displayed for log-in.
Commissioning 8.4 Additional applications Touch screen calibration After concluding the "Panel Wizard" dialog, the touch controller is installed. 1. Calibrate the touch screen. Figure 8-6 Start touch screen calibration 2. Confirm with "OK".
Commissioning 8.4 Additional applications 8.4.2 Key Panel adjustment 1. Select the desired screen size. Note The screen size data can be found on the rating plate of the Key Panel. Figure 8-7 Key Panel; selection of the screen size Figure 8-8 Key Panel; exiting the program 2. Click on the button "Finish".
Commissioning 8.4 Additional applications 8.4.3 RAID1 system (optional) This is a RAID1 system configuration (mirroring with two hard disks). This configuration enhances system availability as the system is able to continue operation if a hard drive fails, or if there is a cable problem at a channel.
Commissioning 8.4 Additional applications RAID system management functions The pre-installed RAID system software offers enhanced functionality for RAID system operation and management. Start the SW by selecting the "Start > Programs > Intel Matrix Storage Manager command. Figure 8-10 Example The "View -> Advanced Mode" command returns details of the RAID volumes. The command "View -> System Report" can be used to create a report with details of the RAID volumes.
Commissioning 8.4 Additional applications Comments about faults Notice Input delay System load may briefly increase due to synchronization when a hard disk has failed, depending on processor load and current hard disk activity. In extreme cases, input from the keyboard and touch screen may be delayed for a brief period. Replacing a faulty RAID system drive Replace faulty RAID drives with a new drive in order to recover secure RAID1 state.
Commissioning 8.4 Additional applications Notice The new HDD can be integrated into the RAID system at operating system level by means of the RAID software. Synchronization may take several hours, depending on system load. Integrating a new hard drive Select the "Rescan for Plug and Play Devices" command to find and indicate the new HDD. You can also choose to reboot the device. In this case, the RAID software automatically integrates the new HDD and synchronizes the RAID system.
Commissioning 8.4 Additional applications The "Rebuild to this Hard drive" command initiates synchronization of the RAID1 system. Figure 8-13 Example Notice The "SIMATIC PC DiagMonitor" diagnostics and alarm software also provides information about the RAID status. This software only needs to be installed once - logons are not required. The diagnostics and alarm software "SIMATIC DiagMonitor " is available as an accessory.
Commissioning 8.4 Additional applications Solution: Before performing a RAID commissioning, the SIMATIC PC DiagMonitor should be deactivated. Subsequently, it can be reactivated. Measures: If the DiagMonitor Management Station is in operation on your device: ● Close all applications, also the Management Station. ● Afterwards, stop the DiagMonitor SNMP Agent (SOL-Agent). In order to do so, select Start > Run and enter cmd in the field. ● Afterwards, enter Net stop snmp and confirm with the Enter key.
Commissioning 8.5 BIOS settings 8.5 BIOS settings The BIOS setting "USB legacy Support" is enabled by default. Thus, the complete functionality of a USB keyboard is available prior to starting up Windows. You can also adjust the BIOS settings with the USB keyboard. Note To edit the BIOS on an operator device equipped with a touch screen, connect a USB keyboard. 8.6 USB Introduction Commercially available USB peripherals can be easily and flexibly connected via the USB interface.
Commissioning 8.6 USB Using USB peripherals Notice When installing a USB device for the first time, make sure you have the required device driver. Before removing an intelligent USB device, deactivate the device in the operating system using the dialog "Unplug or Eject Hardware". For additional information, refer to the documentation for the operating system.
Operation and configuration 9.1 Normal operation Operation and configuration 9.1 Normal operation 9.1.1 Switching on the device 9 Requirement ● The peripheral devices are connected. Caution To comply with the EMC guideline of the device with I/O, ensure that the manufacturer or supplier of the components used guarantees compliance with the regulations. Connect the I/O devices via shielded cables with metal connectors.
Operation and configuration 9.1 Normal operation Procedure Warning Danger of incorrect operations! The following applies to external input devices or combinations of external input devices and control units with key panels: Ambiguous key codes can cause serious malfunctions of the application program. Always activate the "Security features" of "KeyTools." Please note the applicable safety information in the "Operation and configuration" chapter in the section, "Additional drivers and applications.
Operation and configuration 9.1 Normal operation 9.1.2 Logging on to the operating system using the on-screen keyboard The logon dialog is displayed when you have assigned an administrator password. Note An on-screen keyboard (OSK) appears for devices with touch screen panels. You can enter the administrator password directly on the touch screen using the screen keyboard or using the mouse. For additional information, refer to the Microsoft help on screen keyboards. 9.1.
Operation and configuration 9.2 Additional drivers and applications 9.2 Additional drivers and applications The necessary drivers and applications are available on the supplied "Documentation and Drivers" CD. Note The supplied drivers and applications have been system-tested and are approved for this device. No warranty can be provided for other software. Press the "Help" button to obtain information concerning the buttons of a dialog. 9.2.1 Touch screen calibration Procedure 1.
Operation and configuration 9.2 Additional drivers and applications The calibration mask is output on the selected display. 6. Touch the blue arrow. The input is confirmed by a tick, and the next arrow is displayed. 7. Confirm all input prompts (arrows, or crosses in the center) until the complete screen has been calibrated. Note If the touch screen does not react as expected when touched, repeat the calibration. Only an active screen can be calibrated.
Operation and configuration 9.2 Additional drivers and applications 9.2.3 Deactivate touch functionality Description It is possible to deactivate the touch functionality, e.g. if you wish to clean the screen. Procedure 1. Select "Start > Programs > UPDD > Settings". The "UPDD Console" dialog box opens. Figure 9-3 Deactivate touch functionality 2. Select the screen ① you wish to deactivate ①. 3. Remove the tick in the "Enabled" ③ option box in the "Properties" ② tab. The screen is deactivated.
Operation and configuration 9.2 Additional drivers and applications 9.2.4 Windows Security Center (Windows XP Professional / Windows XP Embedded) Call Select "Start > Settings > Control Panel > Security Center". Function The Windows Security Center has the following functions with the corresponding defaults: Function Default setting Firewall on Automatic updates Off Virus protection Off Alarms on The default settings can be activated and deactivated.
Operation and configuration 9.2 Additional drivers and applications Figure 9-5 9.2.5 "Alert Settings" dialog KeyTools (for key panel devices) SIMATIC KeyTools is one selection of the applications for your Panel PC. These applications allow you to adapt key codes that are sent by the key panel of the control unit.
Operation and configuration 9.2 Additional drivers and applications 9.2.6 On-screen keyboard (for touch panel device) You can operate the device by means of a virtual screen keyboard. You can use it to enter the characters directly on the touch panel or with an externally connected mouse. Call "Touch input" Start the "Touch input" application on the desktop. The screen keyboard is displayed.
Operation and configuration 9.2 Additional drivers and applications 9.2.7 Panel PC Tools The program installs program interfaces for the Panel PC.
Operation and configuration 9.2 Additional drivers and applications 9.2.8 CheckLanguageID Scope The following applies to Windows 2000 Professional MUI and Windows XP Professional MUI. Call "c:\drivers\checklang\checklangid.exe" or reinstallation from the "Documentation and Drivers" CD. Function "CheckLanguageID" displays the currently installed languages.
Operation and configuration 9.2 Additional drivers and applications 9.2.9 Multilingual settings for the operating system Windows MultiLanguage MUI operating system enables users to set the language of the GUI to their individual preference. Some elements are not localized, however, and remain in the original language of the system - English. You should therefore always install English language service packs.
Operation and configuration 9.2 Additional drivers and applications 9.2.10 DVD burner The drive of the DVD burner is installed optionally. Recording methods supported by the disk drive: "Disc at once","Track at once", "Session at once", "Packet writing", whereby "Disc at once" and "Track at once" are recommended due to their compatibility to other optical drives. Software In order to utilize full functionality of the DVD drive, you need to install additional software.
Operation and configuration 9.
10 Operation 10.1 Status indicators The two LEDs on the upper left hand side of the control panel display the operating status: ● LED "POWER" green: Active voltage ● LED "TEMP" orange: Temperature threshhold exceeded. The maximum temperature threshold is preset and cannot be changed. Refer to the "Functions" chapter for more information. 10.2 General control elements On / Off switch On / Off switch Description The On/Off switch does not disconnect the device from supply voltage.
Operation 10.3 Device with key panel Warning The On/Off switch does not disconnect the device from supply voltage. 10.3 Device with key panel 10.3.1 Safety Notice Maloperation If you activate several keys simultaneously, a malfunction on the device cannot be excluded. Activate function keys and softkeys only in sequence! Malfunctions of the user software For security reasons, always use "Security features" of the KeyTools.
Operation 10.3 Device with key panel 10.3.2 Overview Overview The number of keys, their labeling and function is the same on all key panels. The various panel types differ in the arrangement of the keys and in the size and type of the display.
Operation 10.3 Device with key panel 10.3.3 Keys 10.3.3.
Operation 10.3 Device with key panel 10.3.3.2 Alphanumeric and numeric keys Alphanumeric keys Enter letters, special characters, blank spaces and underline using the alphanumeric keys. Figure 10-3 Alphanumeric keys 2 (1) Underline (2) Space character Toggling between lower-case and upper-case letters Enter the lower-case letters using the pre-defined assignment of the alphanumeric keys. To enter an upper-case letter, proceed as follows: 1. Hold down the key. 2.
Operation 10.3 Device with key panel Numeric keys Enter the numerals "0" to "9" and special characters, e.g. the decimal point, using the predefined assignment of the numeric keys. Enter special characters, arithmetic signs and signs Special characters, arithmetic signs and signs are also assigned to most of the alphanumeric and numeric keys. These signs are indicated by white symbols on the top left of the keys. To enter such a sign, proceed as follows: 1. Hold down the control key. 2.
Operation 10.3 Device with key panel 10.3.4 External keyboards The keyboard layout has been set to "English/USA international." If you use a keyboard with a layout other than the "English/USA international" layout, the key codes of the internal and external keyboards might no longer correspond. 10.3.5 Using the direct control key module The direct control key module is a module that is intended for use with the SIMATIC Panel PC 677B (exclusively for variants with an integral membrane keyboard).
Operation 10.3 Device with key panel Example: The keyboard codes, that are sent when any key is operated, are stored in a code table. The initial status of the table is as follows: Table 10-1 Keyboard codes Keys: Keyboard code: All standard PC keys "English international" Additional keys for Panel PC 677B F13 to F20 SHIFT+F1 ... SHIFT+F8 S1 ... S4 SHIFT+F9 ... SHIFT+F12 S5 ... S16 CTRL+F1 ...
Operation 10.3 Device with key panel Figure 10-6 Standard assignment of the F13 key Explanation: The key labeled outputs the key code and sets digital input DI 0.0 when the direct key module is used. Refer to the following Internet site for more details about the use of the tool. Enter "Keypad" as the search term under "download". http://www.siemens.
Operation 10.3 Device with key panel 10.3.6 Labelling function keys and softkeys Scope This section applies only to control units with key panels. Introduction The control unit has two horizontal and two vertical keypads Assign user specific functions to the keys as needed. Label the keys with labelling strips from the accessories. Note The device is supplied with a sheet of labeling strips. Caution Labeling Label the function keys and softkeys to conform with the project.
Operation 10.3 Device with key panel Figure 10-7 10.3.7 Rear side of the control unit with connections and slots for the labeling strips for the example of a 12" touch panel front.
Operation 10.4 Device with touch panel 10.4 Device with touch panel The individual variants differ in their dimensions and size of the display. Figure 10-9 10.4.1 Example of a 15" touch panel (1) Display with touch panel (2) USB ports (optional) Operating a touch panel On the display that is touch-sensitive due to the touch sensor, application-specific user interface elements, for example buttons, are displayed.
11 Functions 11.1 Overview Functions implemented: ● Temperature monitoring and over/under-temperature display ● Watchdog ● Fan monitoring Messages of the monitoring modules can be transferred to applications. The SOM software (Safecard On Motherboard) and DiagMonitor software on CD (optional) can be used to handle this functionality. The DiagMonitor software CD contains the monitoring software, the software for the stations to be monitored, and a library for creating user-specific applications.
Functions 11.2 Safecard on Motherboard (SOM) 11.2 Safecard on Motherboard (SOM) Safecard on Motherboard (SOM) This application is used to monitor PC hardware (temperature, watchdog and fans) and to display the current measured values. You can also configure the temperature and fan monitoring functions, and the watchdog function. Your device is equipped with three temperature sensors, which are automatically detected by the application.
Functions 11.3 Temperature monitoring 11.3 Temperature monitoring The temperature is recorded by means of three thermocouples. One thermocouple monitors the processor temperature, another the temperature in the area near the power supply, and a third the air intake temperature next to the DVI port. The following fault reactions are triggered if one of the temperature values exceeds the set temperature threshold: Response Option Device and CPU fans accelerate to maximum speed.
Functions 11.5 Fan monitoring WD monitoring times (TWD) The monitoring times can be set in increments of one second within a range from 3 to 255 seconds. Note The watchdog is retriggered if the monitoring time is changed at the active watchdog (that is while the watchdog is running)! 11.5 Fan monitoring The function monitors operation of the enclosure and power supply fans.
12 Maintenance and service 12.1 Maintenance Scope of maintenance The device is largely maintenance-free. If the functioning of components, such as the backup battery, has been impaired after a limited period of operation, they must be replaced. Please see the relevant chapters of these operating instructions for detailed information.
Maintenance and service 12.1 Maintenance Cleaning agents Use dish soap or foaming screen cleaner only as cleaning agents for the front. The rear side of the operator unit and the housing of the computer unit must only be drycleaned. Caution Do not clean the device with aggresive solvents or scrubbing agents or with pressurized air or steam cleaner. Procedure for cleaning the device (front) 1. Switch off the device. This prevents the accidental triggering of functions when the front is touched. 2.
Maintenance and service 12.2 Spare parts 12.2 Spare parts Replacement part Key panel 12'' TFT 15'' TFT Touch panel 12'' TFT 15'' TFT 17" TFT 19'' TFT Key panel, without front USB port*) 12'' TFT 15'' TFT Touch panel, without front USB port *) 12'' TFT 15'' TFT 17" TFT 19'' TFT Order No.
Maintenance and service 12.3 Separating the control unit from the computer unit 12.3 Separating the control unit from the computer unit The control unit is separated from the computer unit to carry out repairs or to replace the control unit, for example. Procedure 1. Disconnect the device from the mains. 2. Open the switchgear cabinet. The device is now accessible from the back. 3.
Maintenance and service 12.3 Separating the control unit from the computer unit – Screw mounting: Secure the control unit against falling out and unscrew it. – Clamp fastening: Remove the clamps that secure the control unit to the mounting wall.
Maintenance and service 12.3 Separating the control unit from the computer unit Mounting operator control unit on computer unit To mount the operator control unit on the computer unit, perform the steps in reverse: Caution When you swing the control unit and processing unit together, make sure that the flatband cables are correctly folded together and do not get squished. In order to do this, fold the flatband cables gently with specific spacing, as shown.
Maintenance and service 12.4 Removing and installing hardware components 12.4 Removing and installing hardware components 12.4.1 Repairs Repairing components Only authorized personnel are permitted to repair the device. Warning Unauthorized opening and improper repairs may lead to material damage and hazards to users. ● Always disconnect the power connector before you open the device. ● Install only system expansions which are designed for this computer.
Maintenance and service 12.4 Removing and installing hardware components 12.4.2 Opening the Device Caution Work on the open device may only be carried out by authorized and qualified personnel. Within the warranty time, you are only allowed to install expansions for memory and expansion card modules. Caution The device contains electronic components which may be destroyed by electrostatic charge. You therefore need to take precautionary measures before you open the device.
Maintenance and service 12.4 Removing and installing hardware components Open the device up Steps for opening the device 1 Disconnect the device from the mains. 2 Loosen the screws (1). 3 Swing the cover up and remove it.
Maintenance and service 12.4 Removing and installing hardware components 12.4.3 Removing/Installing Memory Module Memory expansion options The motherboard is equipped with 2 slots for memory modules. For 184-pin DDR2 RAM chips, unbuffered, no ECC. This allows you to expand device memory up to 4 GB, of which you can use approx. 3.2 GB for the operating system and applications. You can install one or two modules.
Maintenance and service 12.4 Removing and installing hardware components Removing a memory module How to remove a memory module 1 Open the device. 2 Release the locking mechanism on the left and right. 3 Pull the memory module out of the slot. 4 Close the device. Display of the current memory configuration A new memory module is automatically detected. The allocation of the "base memory and extended memory" is automatically displayed when you switch on the device.
Maintenance and service 12.4 Removing and installing hardware components Installing a memory module How to install a memory module 1 Open the device. 2 Note where the (polarized) cutout is on the pin side of the RAM chip before inserting it. Note: The modules can be installed in any slot. 108 3 Insert the module downwards, applying slight pressure and press it until the locking snaps into place. 4 Close the device.
Maintenance and service 12.4 Removing and installing hardware components 12.4.4 Installing PCI / PCI express cards 12.4.4.1 Notes on the modules The device is designed for use with modules conforming to PCI specifications V 2.2. PCI modules with 5 V and 3.3 V supply voltage and PCI Express x4 modules can be used. The permissible module dimensions are specified in the "Dimensional drawings" section. 12.4.4.2 Installing / removing expansion modules Preparation Disconnect the device from the mains.
Maintenance and service 12.4 Removing and installing hardware components Inserting the card retainer How to install the card retainer 1 Insert the card retainer through the guide slot of the mount. The card retainer must be solidly on the module. Insert the module in the notch. Caution Do not put pressure on the module! Do not apply excessive force to the card retainer when you push it onto the module. 2 Remove any excess part from the card retainer.
Maintenance and service 12.4 Removing and installing hardware components 12.4.5 Installing drives 12.4.5.1 Options of installing disk drives Drive bay module for hard disk drives and optical drives DVD burner drive bay mount Item Description (1) DVD burner drive bay mount (2) Slot for DVD burner drive A 3.5" hard disk drive Item Description (1) Hard disk drive bay for one 3.5" drive (2) Slot for one 3.
Maintenance and service 12.4 Removing and installing hardware components Two 2.5" hard disks Item Description (1) Hard disk drive bay for 2.5" hard disks (2) Two slots for 2.
Maintenance and service 12.4 Removing and installing hardware components 12.4.5.2 Installing/removing a drive bay module Preparations Isolate the device from mains and disconnect all connection cables. Removing a drive bay module for hard disks and optical drives Steps for removing the drive bay 1 Loosen the four screws (1). 2 Lift out the drive bay module for hard disks and the optical drive.
Maintenance and service 12.4 Removing and installing hardware components 12.4.5.3 Removing / installing an optical drive Preparations Isolate the device from mains and disconnect all connection cables. Required tools You need a Torx 6 screwdriver to remove the the DVD burner. Removing the DVD burner drive How to remove a DVD burner drive 1 Remove the drive bay module. 2 Loosen the screws (1) on the DVD burner drive bay. 3 Loosen the screws (2) on the drive.
Maintenance and service 12.4 Removing and installing hardware components 12.4.5.4 Installing / removing hard disks Removing 2.5" drives How to remove a 2.5" drive 1 Remove the drive bay module. 2 Loosen the screw (1) of the drive. 3 Remove the hard disk drive and the steel mounting bracket from the bay. 4 Disconnect the power supply and the data cable from the drive. Removing a 3.5" drive How to remove a 3,5" drive 1 Remove the drive bay module.
Maintenance and service 12.4 Removing and installing hardware components 12.4.6 Installing/removing an on-board Compact Flash card Notice We highly recommend that use use approved SIMATIC Compact Flash cards. Siemens disclaims any liability for impairment of functions caused by the use of third-party cards. Memory expansion options The device features a slot for Compact Flash cards types I / II. Notice This slot is not hot-plug capable.
Maintenance and service 12.4 Removing and installing hardware components Opening the board slot How to install a Compact Flash card 1 Remove the screws. 2 Slide the cover plate of the module slot towards the DVI connection and lift it out.
Maintenance and service 12.4 Removing and installing hardware components Installing the Compact Flash card How to install a Compact Flash card 1 Open the board slot. 2 Insert the Compact Flash card in the slot with the connector facing in until it locks into place. 3 Open the module slot. Note The Compact Flash slot is coded against reversed insertion. Insert the Compact Flash card so that its label side is facing the front panel of the PC.
Maintenance and service 12.4 Removing and installing hardware components Removing the Compact Flash card How to remove a Compact Flash card 12.4.7 1 Open the board slot. 2 Press the eject button, for example with the cover of the module slot, and remove the Compact Flash card. 3 Open the module slot. Installing/removing an additional Compact Flash card Notice We highly recommend that use use approved SIMATIC Compact Flash cards.
Maintenance and service 12.4 Removing and installing hardware components Installing the additional Compact Flash card How to install the Compact Flash card in the Compact Flash adapter 120 1 Remove the hard disk cover. 2 Lift out the Compact Flash adapter module and lay it on the device.
Maintenance and service 12.4 Removing and installing hardware components How to install the Compact Flash card in the Compact Flash adapter 3 Open the Compact Flash latch. 4 Insert the Compact Flash card in the adapter with the connector facing in until it locks into place.
Maintenance and service 12.4 Removing and installing hardware components How to install the Compact Flash card in the Compact Flash adapter 12.4.8 5 Close the Compact Flash latch. 6 Mount the hard disk cover. Replacing the Backup Battery Note Batteries are wearing parts and should be replaced every five years in order to ensure proper functioning of the PC.
Maintenance and service 12.4 Removing and installing hardware components Warning Risk of explosion and release of harmful substances! For this reason, do not burn lithium batteries, do not solder on the cell body, do not open, do not short circuit, do not reverse polarity, do not heat above 100°C, dispose of correctly, and protect against direct sunlight, dampness and dew. Disposal Caution Batteries must be disposed of in accordance with local regulations.
Maintenance and service 12.4 Removing and installing hardware components Replacing the battery Follow the steps outlined below: Steps for replacing the battery 124 1 Open the battery compartment. 2 Remove the battery holder. 3 Detach the cable. 4 Remove the old battery.
Maintenance and service 12.4 Removing and installing hardware components Steps for replacing the battery 5 Fasten the new battery and reinsert the battery holder. 6 Close the battery compartment. Reconfiguring the BIOS setup If the battery replacement took longer than 30 seconds, the configuration data of the device have been deleted and you need to reconfigure these in the BIOS Setup. 12.4.
Maintenance and service 12.4 Removing and installing hardware components Removing the power supply unit How to remove the power supply module 1 Remove the drive bay module for the hard disk and DVD burner. 2 Loosen the screws (1) and remove the power supply cover. 3 Remove the screws (1) (Torx T10).
Maintenance and service 12.4 Removing and installing hardware components How to remove the power supply module 4 Detach the power plug (1) from the power supply module. 6 Lift out the power supply module.
Maintenance and service 12.4 Removing and installing hardware components 12.4.10 Installing / removing the bus board Preparation 1. Isolate the device from mains and disconnect all connection cables. 2. Open the device. Removing the bus board How to remove the bus board 1 Remove all modules from the slots. 2 Lift out the drive bay module for hard disks and the DVD burner. 3 Loosen the screws (1) and remove the power supply cover. 4 Remove the power supply.
Maintenance and service 12.4 Removing and installing hardware components 12.4.11 Installing / removing the motherboard Preparation 1. Isolate the device from mains and disconnect all connection cables. 2. Open the device. Removing the motherboard How to remove the motherboard 1 Remove the drive bay module for the hard disk and DVD burner. 2 Loosen the screws (1). Remove the module bracket (2). 3 Remove the power supply cover. 4 Remove the bus board. 5 Remove the power supply.
Maintenance and service 12.4 Removing and installing hardware components How to remove the motherboard 130 8 Remove the hexagon bolts (6 pieces) from the ports. 9 Remove the motherboard.
Maintenance and service 12.4 Removing and installing hardware components 12.4.12 Installing / removing the equipment fan Preparations 1. Disconnect the device from the mains. 2. Open the device. Removing the fan How to remove the fan 1 Pull the fan plug from the motherboard. 2 Loosen the four two plastic rivets on the enclosure. 3 Take the fan out of the enclosure.
Maintenance and service 12.4 Removing and installing hardware components Installing the fan Notice Always install a fan of the same type! Fan mounting position The figure shows the correct fan mounting position. Pay attention to the direction of the arrow on the fan enclosure! 12.4.13 Installing / removing the power supply fan Preparations 1. Disconnect the device from the mains. 2. Open the device. 3. Remove the power supply.
Maintenance and service 12.4 Removing and installing hardware components Removing the fan How to remove the fan 1 Pull out the fan connector. 2 Loosen the four screws on the enclosure. 3 Take the fan out of the enclosure.
Maintenance and service 12.4 Removing and installing hardware components Installing the fan Notice Always install a fan of the same type! Fan mounting position The diagram shows the correct mounting position of the fan (1).
Maintenance and service 12.4 Removing and installing hardware components 12.4.14 Installing / removing the processor Caution The processor replacement may only be carried out by authorized qualified personnel. Preparation 1. Disconnect the device from the mains. 2. Open the device. 3. Remove the drive bay module. 4. Remove the power supply cover. Removing the processor How to remove the processor 1 Remove the four screws from the processor heat sink and remove the heat sink.
Maintenance and service 12.4 Removing and installing hardware components How to remove the processor 136 2 Loosen the processor latch. 3 Remove the processor.
Maintenance and service 12.4 Removing and installing hardware components Installing the processor Note When you insert the processor, make sure the markings on the processor and on the socket match up. Notice The processor may overheat when the system is in operation! Apply the heat-conductive paste very evenly, as a thin film! How to install the processor 1 Insert the processor. 2 Close the processor latch. 3 Apply the heat-conductive paste on the processor.
Maintenance and service 12.5 Reinstalling the operating system 12.5 Reinstalling the operating system 12.5.1 Windows XP Embedded 12.5.1.1 General installation procedure If your software becomes corrupt for any reason, you can return it to the factory state using the Restore DVD. The Restore DVD contains a image file for the Compact Flash card with the original software (operating system with installed hardware drivers) and is included in the Windows XP Embedded package variant.
Maintenance and service 12.5 Reinstalling the operating system Restoring factory state To restore the factory state, proceed as follows: 1. If the device does not have an optical drive, connect a USB DVD-ROM drive to the device. 2. Insert the Restore DVD in the drive and reboot the device. When the BIOS message Press to enter Setup or to show Boot menu appears, press the F2 key. 3. Select the Boot menu and move the entry "DVD Drive" to the first position. 4.
Maintenance and service 12.5 Reinstalling the operating system 12.5.2 Windows XP Professional / Windows 2000 Professional 12.5.2.1 General installation procedure If your software becomes corrupt for any reason, you have two possibilities: ● Restoring the factory state of the software with the Restore DVD The Restore DVD contains an image file of the original supplied software (operating system with installed drivers) and is included in the Windows XP Professional variant.
Maintenance and service 12.5 Reinstalling the operating system Restoring factory state To restore the factory state, proceed as follows: 1. If the device does not have an optical drive, connect a USB DVD-ROM drive to the device. 2. Insert the Restore DVD in the drive and reboot the device. When the BIOS message Press to enter Setup or to show Boot menu appears, press the F2 key. 3. Select the Boot menu and move the entry "CD-ROM Drive" to the first position. 4.
Maintenance and service 12.5 Reinstalling the operating system Setting up the language selection for Windows 2000 Professional The Multilanguage User Interface (MUI) allows you to set up the Windows 2000 menus and dialogs for additional languages.
Maintenance and service 12.5 Reinstalling the operating system Partition setup Set up the hard disk partitions after having installed a new hard disk, or to repair faulty partitions, or to change the partitioning. Caution When you delete or create partitions or logical DOS partitions, you lose all data on the hard disk. All partitions on the hard disk will be deleted. With Windows XP/2000 operating systems, the factory state features two partitions with an NTFS file system on the hard disk.
Maintenance and service 12.5 Reinstalling the operating system Format primary partition 1. Boot from the Recovery DVD to format the partitions. Follow the screen instructions until the Recovery functions window is displayed. 2. Select "Start command prompt" in the Recovery functions window. In the command interface that opens, enter the following command: format DL:/FS:File System DL = Drive letter of the partition to be formatted. Valid values: C, D, E, F etc.
Maintenance and service 12.5 Reinstalling the operating system Note If you want to use Windows XP as a professional you should have the following manual (not included in the scope of delivery) available: Microsoft Windows XP Professional, the technical reference" (MSPress Nr 934) this manual contains special information for administrators involved in installing, managing and integrating Windows in networks or multi-user environments.
Maintenance and service 12.5 Reinstalling the operating system Setting up the language selection for Windows 2000 Professional The Multilanguage User Interface (MUI) allows you to set up the Windows 2000 menus and dialogs for additional languages. To install the MUI, start the "MUISETUP.EXE" program in directory CD_DR:\SOURCE\MUI on the Recovery DVD. Follow the on-screen instructions, in order to install the required languages.
Maintenance and service 12.6 Partitioning the hard disk 12.6 Partitioning the hard disk 12.6.1 Setting up the partitions under Windows XP Embedded You need to set up the partitions on the Compact Flash card after installed a new Compact Flash card or to repair corrupt partitions or to change the partitioning. Partitioning the Compact Flash card The factory state of the Compact Flash card includes the following partitions: Partition Name Size of card 2 GB File system 1.
Maintenance and service 12.7 Installing drivers and software 12.7 Installing drivers and software 12.7.1 Installing drivers and software Notice Before you install new drivers or updates for multilingual operating systems, (MUI versions), reset the regional settings for menus and dialogs and the default language to US English. Install the drivers and software from the included "Documentation and Drivers" CD. Procedure: 1. Place the CD into the drive. 2. Start the program with "START". 3.
Maintenance and service 12.8 Installing the RAID Controller software 12.8 Installing the RAID Controller software Note You find the procedure for installing the RAID controller software in the RAID user manual on the supplied "Documentation and Drivers" CD. Windows 2000 Professional / XP Professional You need to select the Intel 82801GR/GH SATA RAID Controller from the provided list when installing Windows 2000 Professional /XP Professional for the first time. 12.
Maintenance and service 12.10 Installing updates 12.10 Installing updates 12.10.1 Updating the operating system Windows XP Embedded An update of the operating systems is only possible with a new version of the Restore CD. Please contact customer support for more information about its availability. Windows XP Professional Monthly updates for the Windows XP Professional operating system are available on the Internet under: http://www.microsoft.
Maintenance and service 12.11 Data backup 12.11 Data backup 12.11.1 Creating an image Data backup under Windows XP Embedded/Windows XP Professional To back up data under Windows XP Embedded / Windows XP Professional, we recommend the software tool "SIMATIC PC/PG Image Creator". This tool provides comfortable and efficient functions for backup and restoring the full content of Compact Flash cards, HDDs and individual partitions (images.
Maintenance and service 12.
Alarm, error, and system messages 13.1 13 Boot error messages BIOS first performs a Power On Self Test (POST) within the boot routine to verify proper operation of certain functional units of the PC. If an error is detected within this phase, BIOS outputs a beep code based on the current test result. The boot sequence is interrupted immediately if fatal errors occur. If the POST does not return an error, the BIOS initializes and tests further functional units.
Alarm, error, and system messages 13.1 Boot error messages 154 On-screen error message Key seizure Meaning / suggestions System RAM Failed at offset: Memory error. Contact your technical support team. Shadow RAM Failed at offset: Memory error. Contact your technical support team. Extended RAM Failed at offset: Memory error. Contact your technical support team. Failing Bits: Memory error. Contact your technical support team.
Alarm, error, and system messages 13.2 Introduction to the BIOS beep codes 13.2 Introduction to the BIOS beep codes The device performs a self-test when it is switched on. If an error is detected during the POST (Power On Self-Test), a series of beep signals are issued. The beep tones are a code for errors and are composed of 2 x 2 sequences.
Alarm, error, and system messages 13.3 BIOS beep codes 13.3 BIOS beep codes The following section lists the POST codes relevant to users in the sequence in which they occur: Contact Customer Support for information on all other POST codes.
Alarm, error, and system messages 13.3 BIOS beep codes Special codes The following special code are provided in addition to the beep codes: Special code Meaning 3x short The key is pressed during the system start: The on-board device installation is skipped. The on-board graphic controller is used as the default display. 1x long 8x short Error reading the MPI system information. Contact customer service. 4x short MPI-EPROM programmed for the first time.
Alarm, error, and system messages 13.
14 Troubleshooting/FAQs 14.1 General problems This chapter provides you with tips on how to localize and troubleshoot frequently occurring problems. Problem Possible causes Remedy The device is not operational There is no power supply to the device. • • Check the power supply, the network cable and the power plug. Check if the On/Off switch is in the correct position. Device is being operated outside the specified ambient. conditions • • Check the ambient conditions.
Troubleshooting/FAQs 14.1 General problems Problem Wrong time and/or date on the PC. Possible causes Although the BIOS setting is OK, the time and data are still wrong. The backup battery is dead. Replace the backup battery. USB device not responding. The USB ports are disabled in your BIOS. Use a different USB port or enable the port. USB 2.0 device connected but USB 2.0 is disabled. Enable USB 2.0. Operating system does not support the USB port.
Troubleshooting/FAQs 14.2 Problems when Using Modules of Third-party Manufacturers 14.2 Problems when Using Modules of Third-party Manufacturers Problem Possible cause The PC crashes during startup • • • • • Double allocation of I/O addresses Double allocation of hardware interrupts and/or DMA channels Signal frequencies or signal levels are incorrect. Connector assignments deviate.
Troubleshooting/FAQs 14.
15 Specifications 15.1 General specifications Electrical specifications Supply voltage AC Nominal 100 - 240 V AC (-15% / +10%), autorange Supply voltage DC Nominal 24 V DC (-15% / + +20%), SELV AC device: Frequency 50 to 60 Hz, 47 to 63 Hz Input current AC Continuous current to 2.3 A (to 50 A for 1 ms at startup) Input current DC Continuous current to 9 A (to 14 A for 30 ms at startup) Line voltage frequency 50 to 60 Hz (47 to 63 Hz) Transient voltage interruption Namur Max.
Specifications 15.
Specifications 15.1 General specifications Motherboard Processor • • • Intel ® Celeron M 440 1.86 GHz 533 MHz Front Side Bus (FSB), 1024 KB Second Level Cache Intel ® Core 2 Duo 1.66 GHz T5500 667 MHz Front Side Bus 2048 KB Second Level Cache Intel ® Core 2 Duo 2.
Specifications 15.1 General specifications Ports Ethernet 2x Ethernet interface (RJ45) 10/100/1000 Mbps Intel 82573 L COM1 Serial interface, 9-pin Cannon plug Compact Flash Slot for Compact Flash card Status displays Control unit • • Power LED Temperature LED Computer unit • • Ethernet LEDs Optical drive LED Display Graphics controller Intel Graphics memory Graphics memory; 8 to 132 MB, taken from RAM.
Specifications 15.
Specifications 15.1 General specifications Safety Protection class Protection class I to IEC 60536, i.e.
Specifications 15.2 Power requirements of the components 15.2 Power requirements of the components Basic device Components Voltage +5 V +3.3 V +12 V -12 V Motherboard 3A 5.8 A 0.01 A 0.02 A Core 2 Duo or Celeron M processor 7A Hard diskdrive; 1x 3.5" or Hard disk-drive; 2x 2.5" 1) 0.6 A DVD burner drive 1) 0.8 A 0.8 A Device fan 0,4 A Power supply fan 0,15 A Total (base device) 11.4 A 5.8 A 1.36 A 0.02 A PCI / PCIexpress slots (total) 4A 2) 0.6 A 0.20 A Front panel port 1.
Specifications 15.3 Device with AC voltage supply 15.3 Device with AC voltage supply Specifications Input voltage 100 V - 240 V AC (85 V - 265 V) autorange Input current Continuous current up to 2.3 A, starting current 23 A < 5 ms Frequency 50 to 60 Hz, 47 to 63 Hz Power consumption Max. 140 W for 12" and 15" control unit 1) Max.
Specifications 15.4 Device with DC voltage supply 15.4 Device with DC voltage supply Specifications Input voltage 24 V DC (20.4 to 28.8 V DC) Input current Continuous current to 9 A (to 14 A for 30 ms at startup) Power consumption Max. 140 W for 12" and 15" control unit 1) Max.
Specifications 15.5 Keyboard table 15.5 Keyboard table Key codes The following table applies only to control units with key panels. It contains all characters that can be entered in SIMATIC KeyTools in the "Key code table" area and under "User specific". The character that is triggered by pressing a specific key is listed in the "Display/function" column. Further information is available in the documentation for SIMATIC KeyTools on the "Documentation and Drivers" CD.
Specifications 15.
Specifications 15.
Specifications 15.
Specifications 15.5 Keyboard table Name \| 31 Check-box Display/function L Shift/R Shift } R Alt » — \ L Shift/R Shift | R Alt ¬ R Alt+L Shift/R Shift ¦ Europe 1 Europe 1 32 — ;: 33 — ; L Shift/R Shift : R Alt ¶ R Alt+L Shift/R Shift ° ’" 34 — L Shift/R Shift " R Alt ´ R Alt+L Shift/R Shift ¨ ‘ ‘~ 35 — L Shift/R Shift ~ ,< 36 — , L Shift/R Shift < R Alt ç R Alt+L Shift/R Shift Ç — . L Shift/R Shift > .
Specifications 15.
Specifications 15.
16 Dimensional drawings Dimensional drawings Panel PC 677B , - PP . 16.
Dimensional drawings 16.
Dimensional drawings 16.2 Dimensional drawings for the installation of expansion modules 16.
Dimensional drawings 16.
17 Detailed descriptions 17.1 Motherboard 17.1.1 Structure and functions of the motherboard The essential components of the motherboard are the processor and the chip set, two slots for memory modules, internal and external interfaces and the Flash BIOS.
Detailed descriptions 17.1 Motherboard 17.1.2 Technical features of the motherboard Component / interface Description Characteristics Chip set Single chip set • Intel 945 GM and ICH7R BIOS Update by means of software • Phoenix BIOS V05.01.xx (with Profibus) CPU Intel ® Core 2 Duo / Intel ® Celeron M • On-board L2 cache with 4096/2048/1024 KB Memory 2 DIMM module slots, max. 2 GB/DIMM • • • • • 64-bit data bus width 3.
Detailed descriptions 17.1 Motherboard 17.1.3 Position of the interfaces on the motherboard Ports The motherboard of the device features the following interfaces: ● Interfaces for the connection of external devices ● Interfaces for internal components (drives, bus boards etc.) The figure below shows the location of the internal and external interfaces on the motherboard.
Detailed descriptions 17.1 Motherboard 17.1.4 External ports Interface Position Connector Description USB 2.
Detailed descriptions 17.1 Motherboard PROFIBUS/MPI interface 1) 4 RTS_AS RTSAS, control signal for received data stream. The signal is "1" when the directly connected AS is sending. Input 5 M5EXT M5EXT return line (GND) of 5 V supply. The current load of an external consumer connected between P5EXT and M5EXT may not exceed the 90 mA. Output 6 P5 EXT P5EXT power supply (+5 V) of the 5 V power supply.
Detailed descriptions 17.1 Motherboard Ethernet RJ45 connection, X40, X41 Ethernet RJ45 connection /(' /(' Pinno.
Detailed descriptions 17.1 Motherboard DVI-I port, X302 DVI-I port Pinno.
Detailed descriptions 17.1 Motherboard Compact Flash card, X4 Compact Flash card port Pin no.
Detailed descriptions 17.1 Motherboard Serial port COM 1, X616 The COM1 serial port has the following pin assignment: Serial interface COM1 Pinno. 17.1.
Detailed descriptions 17.1 Motherboard Display interfaces TFT displays with an LVDS interface can be connected to this interface. You can connect 18-bit displays with a resolution up to 1024 x 768 pixels on X400 only (single-channel LVDS), and of 1280 x 1024 pixels on X400 and X401 (dual-channel LVDS). On the X401, there is also +12 V as supply voltage for the backlight inverter (max. 4.2 A) for 19" / Dual Channel LVDS displays. The permitted display clock rate is 20 MHz to 66 MHz.
Detailed descriptions 17.1 Motherboard Display interface (2nd LVDS channel), X401 Pin no.
Detailed descriptions 17.1 Motherboard Assignment of the display to the display select pins One of the 15 available displays is configured automatically via the display select inputs. The display select inputs are connected to pull–up resistors, i.e. if these inputs are not interconnected, they are high level. The input must be connected to ground to generate a low level. Pin no.
Detailed descriptions 17.1 Motherboard Pin no.
Detailed descriptions 17.1 Motherboard 17.1.6 Internal interfaces Pin assignment of the internal ports Interface Positio n Connecto Description r Memory Internal X19, X20 2 DIMM sockets, 64-bit Processor Internal X1 Socket for FCPGA processor Bus expansion Internal X10 Socket for bus expansion, assigned PCI bus signals Power supply Internal X13 20-pin connector plug for power supply Hard disk drive Serial ATA Internal X50, X51 Serial ATA, max.
Detailed descriptions 17.1 Motherboard Pin no.
Detailed descriptions 17.1 Motherboard Pin assignment of the supply for the power supply fan, X129 Pin no. Short description Meaning Input / output 1 GND Ground - 2 +12 V Switched voltage supply Output 3 PG1 FAN_CLK Clock signal Input Connection for backup battery, X24 (BATT) A battery for buffering the CMOS RAM is connected to this connector. This is a 3 V Lithium battery with a capacity of 750 mAh. Pin no.
Detailed descriptions 17.1 Motherboard Pin assignment of the internal USB interface connector, X43 Pin no. Short description Meaning Input / output 1 VCC 3.3V +3.
Detailed descriptions 17.2 Bus board 17.2 Bus board 17.2.1 Layout and principle of operation The bus board is designed as a link between the motherboard and the expansion modules. It is secured with two screws. Two models of the bus board are available: Variant 1 has two PCI slots (1x short, 1x long). It can host expansion modules conforming to PCI specification (Rev. 2.2) for 5 V and 3.3 V modules. All PCI slots are master compatible.
Detailed descriptions 17.2 Bus board 17.2.2 PCI slot pin assignment 5V System Environment Side B Side A 1 -12V TRST# 2 TCK +12V 3 Ground TMS 4 TDO TDI 5 +5V +5V 6 +5V INTA# 7 INTB# INTC# 8 INTD# +5V 9 PRSNT1# Reserved 10 Reserved +5 V (I/O) 11 PRSNT2# Reserved 12 Ground Ground 13 Ground Ground 14 Reserved Reserved 15 Ground RST# 16 CLK +5 V (I/O) 17 Ground GNT# 18 REQ# Ground 19 +5 V (I/O) Reserved 20 AD[31] AD[30] 21 AD[29] +3.
Detailed descriptions 17.2 Bus board 5V System Environment 17.2.3 38 Ground STOP# 39 LOCK# +3.3V 40 PERR# SDONE 41 +3.3V SBO# 42 SERR# Ground 43 +3.3V PAR 44 C/BE[1]# AD[15] 45 AD[14] +3.3V 46 Ground AD[13] 47 AD[12] AD[11] 48 AD[10] Ground 49 Ground AD[09] 50 CONNECTOR KEY 51 CONNECTOR KEY 52 AD[08] C/BE[0]# 53 AD[07] +3.3V 54 +3.
Detailed descriptions 17.2 Bus board 17.2.
Detailed descriptions 17.3 System resources 17.3 System resources 17.3.1 Currently allocated system resources All system resources (hardware addresses, memory configuration, allocation of interrupts, DMA channels) are assigned dynamically by the Windows OS, depending on the hardware configuration, drivers and connected external devices. You can view the current configuration of system resources or possible conflicts with the following operating systems: Windows 2000/XP 17.3.
Detailed descriptions 17.
Detailed descriptions 17.3 System resources I/O address (hex) 17.3.2.
Figure 17-3 )XQFWLRQ SIMATIC Panel PC 677B Operating Instructions, 05/2007, A5E01035609-01 ; ; ; = ; = ; = = = ; = = = = ; ; ; ; < < % $ < & < ' ( ) < < * < < < + = = BIOS default interrupt in PIC mode (e.g.
Figure 17-4 )XQFWLRQ 3&, ,54 OLQH $ 3&, ,54 OLQH % 3&, ,54 OLQH & 3&, ,54 OLQH ' = = = = = = = = = = = = < $ < % < & < ' < < ( +RVW 3&, ,54V $ WR + DUH DVVLJQHG IL[HG ,54V LQ $3,& PRGH +RVW 3&, ,54V $ WR + DUH DXWRPDWLFDOO\ DVVLJQHG ,54V LQ 3,& PRGH E\ %,26 D VSHFLILHG RUGHU FDQQRW EH IRUFHG 3&, ,54 OLQH $ 3&, ,54 OLQH % 3&, ,54 OLQH & 3&, ,54 OLQH ' Slot 2 PCIexpress 3&, ,54 OLQH
Detailed descriptions 17.3 System resources 17.3.2.3 Exclusive PCI hardware interrupt Applications demanding a high-performance interrupt require a high-speed hardware interrupt reaction. The PCI hardware interrupt should be used only by one resource in order to ensure high-speed reaction of the hardware.
Detailed descriptions 17.3 System resources 17.3.2.4 Memory address assignments PCI VGA modules can be operated with expansion ROM up to 48K.
Detailed descriptions 17.4 BIOS Setup 17.4 BIOS Setup 17.4.1 Overview BIOS Setup program BIOS Setup program is stored in ROM BIOS. Information about the system configuration is stored in the battery-backed memory of the device. SETUP can be used to define the hardware configuration (for example, the hard disk type) and system properties. SETUP is also used to set the time and date of the realtime clock.
Detailed descriptions 17.4 BIOS Setup 17.4.3 BIOS Setup menus The various menus and submenus are listed on the next pages. You can obtain information on the selected SETUP item from the "item-specific help" part of the respective menu. 3KRHQL[%,26 6HWXS 8WLOLW\ 0DLQ $GYDQFHG %RRW ,'( &KDQQHO 0DVWHU ,'( &KDQQHO 6ODYH 6$7$ 3RUW 6$7$ 3RUW 6$7$ 3RUW 6$7$ 3RUW >&' 520@ >1RQH@ > 0%@ >1RQH@ >1RQH@ >1RQH@ 0HPRU\ &DFKH %RRW 2SWLRQV .
Detailed descriptions 17.4 BIOS Setup Menu layout The screen is divided into four sections. In the top part (2), you can select the menu forms [Main], [Advanced], [Security], [Boot], [Version], [Exit]. In the left of the center section (3) you can select various settings or submenus. Brief help texts appear on the right (4) for the currently selected menu entry. The bottom section contains information for operator input. The figures below represent examples of specific device configurations.
Detailed descriptions 17.4 BIOS Setup 17.4.4 Main menu 3KRHQL[%,26 6HWXS 8WLOLW\ 0DLQ 6HFXULW\ %RRW 6\VWHP 7LPH 6\VWHP 'DWH > @ > @ ,'( &KDQQHO 0DVWHU ,'( &KDQQHO 6ODYH 6$7$ 3RUW 6$7$ 3RUW 6$7$ 3RUW 6$7$ 3RUW >&' 520@ >1RQH@ > 0%@ >1RQH@ >1RQH@ >1RQH@ 0HPRU\ &DFKH %RRW 2SWLRQV .H\ERDUG )HDWXUHV +DUGZDUH 2SWLRQV >(QDEOHG@ 6\VWHP 0HPRU\ ([WHQGHG 0HPRU\ .% .
Detailed descriptions 17.
Detailed descriptions 17.
Detailed descriptions 17.4 BIOS Setup LBA Mode Control The "Enabled" setting at the "LBA Mode Control" (enabled, disabled) option means that hard disk capacities greater than 528 MB are supported. The value depends on the drive and should only be set by way of "Auto" setting at the "Type" field.
Detailed descriptions 17.
Detailed descriptions 17.4 BIOS Setup LBA Mode Control The "Enabled" setting at the "LBA Mode Control" (enabled, disabled) option means that hard disk capacities greater than 528 MB are supported. The value depends on the drive and should only be set by way of "Auto" setting at the "Type" field.
Detailed descriptions 17.
Detailed descriptions 17.4 BIOS Setup 3KRHQL[%,26 6HWXS 8WLOLW\ &38 7\SH &38 6SHHG ,QWHO 5 &RUH 70 &38 7 *+] 6\VWHP 520 6\VWHP 0HPRU\ .% %,26 'DWH ([WHQGHG 0HPRU\ .% .% 6KDGRZ 5DP &20 3RUWV .
Detailed descriptions 17.4 BIOS Setup "Keyboard Features" field The following shortcut menu appears when you select the option "Keyboard Features" in the main menu: 3KRHQL[%,26 6HWXS 8WLOLW\ 0DLQ .H\ERDUG )HDWXUHV 1XP/RFN .H\ &OLFN .H\ERDUG DXWR UHSHDW UDWH .
Detailed descriptions 17.
Detailed descriptions 17.4 BIOS Setup Entry Dual view DVI/CRT Meaning [Disabled] The fan always runs at full speed. [Disabled] Only one CRT or DVI monitor is driven. [Enabled] When a CRT and a DVI monitor are connected, both are activated. Note The second Ethernet interface support is OS dependent. For DOS based applications (e.g. Image Creator) please use the first Ethernet interface. Note For or operation without a monitor (= headless operation), Dual view DVI/CRT should be set to "Disabled".
Detailed descriptions 17.4 BIOS Setup 17.4.
Detailed descriptions 17.4 BIOS Setup Legacy USB support [Disabled] Disables Legacy Universal Serial Bus support [Enabled] Enables Legacy Universal Serial Bus support The USB Boot function must be enabled to allow booting from a USB device, or if the system is to be operated without USB support with a USB keyboard or mouse.
Detailed descriptions 17.
Detailed descriptions 17.
Detailed descriptions 17.
Detailed descriptions 17.
Detailed descriptions 17.4 BIOS Setup 17.4.6 Security menu You can only edit the fields enclosed in square brackets. Two passwords can be assigned to protect your PC from unauthorized use. The Supervisor password can be used to restrict access to the hard disks.
Detailed descriptions 17.4 BIOS Setup User password is Disabled The password is disabled. Enabled Certain Setup fields are configurable by the user, including the user password. The field resets automatically from [Disabled] to [Enabled] when the password is entered. Set User Password This field opens the password input dialog. Logged on users can change the password, or clear and deactivate it by pressing "Return." Set Supervisor Password This field opens the password input dialog.
Detailed descriptions 17.4 BIOS Setup 17.4.7 Boot Menu This menu allows you to assign a priority for the boot devices. 3KRHQL[%,26 6HWXS 8WLOLW\ 0DLQ $GYDQFHG 6HFXULW\ %RRW %RRW SULRULW\ RUGHU 86% .
Detailed descriptions 17.4 BIOS Setup 17.4.8 Version Menu This menu contains system information which should be made available to Technical Support.
Detailed descriptions 17.4 BIOS Setup 17.4.9 Exit menu You always exit BIOS Setup in this menu.
Detailed descriptions 17.4 BIOS Setup 17.4.10 BIOS Setup default settings Documenting your device configuration If you have changed any default settings in Setup, you can enter them in the following table. You can then refer to these entries for any future hardware modifications. Note Print out the table below and keep the pages in a safe place once you made your entries. Note The default setup settings vary depending on the ordered device configuration.
Detailed descriptions 17.
Detailed descriptions 17.4 BIOS Setup SATA/PATA Configuration PATA Controller: Enabled SATA Controller mode Enhanced * 1) AHCI Configuration Disabled * 1) RAID support Disabled * 1) Security Supervisor password is Disabled User password is Disabled Set User Password Enter Set Supervisor Password Enter Password on boot Disabled Fixed disk boot sector Standard Boot Boot priority order: Excluded from boot order: Version SIMATIC PC SIMATIC BoxPC627B/ PanelPC677B BIOS Version V05.01.
A Appendix A.1 A.1.
Appendix A.1 Certificates and guidelines Caution This is a system of Class A. The equipment may cause RF interference in residential areas. In this case, the operating company may be held liable for taking appropriate measures. Low-voltage directive The device with AC power pack complies with the requirements of EC directive 73/23/EEC (Low-Voltage Guidelines). Compliance has been verified by a test in accordance with the EN 60950-1 standard.
Appendix A.1 Certificates and guidelines A.1.2 Certificates and approvals DIN ISO 9001 certificate The quality assurance system for the entire product process (development, production, and marketing) at Siemens fulfills the requirements of ISO 9001 (corresponds to EN 29001: 1987). This has been certified by DQS (the German society for the certification of quality management systems). EQ-Net certificate no.
Appendix A.1 Certificates and guidelines USA Modifications Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment. Conditions of operations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Appendix A.1 Certificates and guidelines A.1.3 Service and support Local information If you have questions about the products described in this document, you can find help at: http://www.siemens.com/automation/partner Technical documentation for SIMATIC products Further documentation for SIMATIC products and systems can be found at: http://www.siemens.com/simatic-tech-doku-portal Easy shopping with the A&D Mall Catalog & online ordering system http://www.siemens.
Appendix A.
B List of Abbreviations/Acronyms B.
List of Abbreviations/Acronyms B.
List of Abbreviations/Acronyms B.
List of Abbreviations/Acronyms B.1 Abbreviations Abbreviation Term UMA Unified Memory Architecture URL Uniform Resource Locator USB Universal Serial Bus UXGA Ultra Extended Graphics Array V.24 Meaning Designation of the full address of an Internet page Graphic standard, maximum resolution 1.600 x 1.
Glossary Automation system (AS) The programmable logical controllers (PLC) of the SIMATIC S7 system consist of a central controller, one or more CPUs, and various I/O modules. Backup Duplicate of a program, data carrier or database, used either for archiving purposes or for the protection of vital and non-replaceable data against loss when the working copy is corrupted.
Glossary COM interface The COM interface is a serial V.24 interface. The interface is suitable for asynchronous data transfer. Configuration files These are files containing data which define the configuration after restart. Examples of such files are CONFIG.SYS, AUTOEXEC.BAT and the registry files . Configuration software The configuration software updates the device configuration when new modules are installed .
Glossary Energy options The energy options can be used to reduce energy consumption of the computer, while keeping it ready for immediate use. This can be configured in Windows by selecting Settings > Control Panel > Energy options. ESD guidelines Directive for using electrostatic sensitive components. Ethernet Local network (bus structure) for text and data communication with a transfer rate of 10/100 Mbps.
Glossary Legacy USB support Support of USB devices (e.g. mouse, keyboard) on the USB ports without driver. License key The license key represents the electronic license stamp of a license. Siemens provides the license keys for protected software. License key diskette The license key diskette contains the authorizations or license keys required to enable protected SIMATIC software.
Glossary Plug&Play PC requires both a BIOS that supports Plug&Play and a Plug&Play expansion card. POST Self-test performed by the BIOS after the computer is switched on. Performs a RAM test and a graphic controller test, for example. The system outputs audible signals (beep codes) if the BIOS detects any errors; the relevant message indicating cause of error is output on the screen.
Glossary Restore DVD The Restore DVD is used to restore the system partition or the entire hard disk to factory state if the system has crashed. The bootable DVD contains all the necessary image files. You can also create a boot disk allowing restoration via the network. SETUP (BIOS Setup) A program in which information about the device configuration (that is, the configuration of the hardware on the PC/PG) is defined. The device configuration of the PC/PG is preset with defaults.
Index A C AC voltage supply, 281 Accessories, 26 Alarms, 83, 84 Allocation of resources, 125 Approval, 11 Approvals, 283 Assignment I/O addresses, 239 Memory addresses, 248 Automatic updates, 83 CE marking, 11, 282 Certificates, 283 Characteristics, 25 Check list, 61 CheckLanguageID, 87 Cleaning agents, 112 COA label, 33 Commissioning, 18, 61 Device, 61 Compact Flash card, 130 Mounting, 133 Partitions, 164 Removing, 134 Computer unit Separating from the control unit, 114 Condensation, 18, 61 Connecting,
Index Data exchange, 57 DC power supply Connecting, 53 DC voltage supply, 281 Defaults BIOS Setup, 275 Degree of protection, 37 IP65 degree of protection, 37 Design Motherboard, 211 Design guidelines, 282 Device, 58, 61, 77 Commissioning, 61 Connecting, 58 Connecting an S7 automation system, 58 couple, 58 Couple, 58 Couple via MPI/PROFIBUS, 58 Open, 119 Separating, 115 Switching on, 77 Device configuration, 275 Device fan, 146, 148 Device fan supply, 229 DiagMonitor Expansion, 27 Diagnostics, 182 BIOS beep
Index I I/O addresses Assignment, 239 Assignment, 239 I/O front ports, 225 IDE channel, 254 Identification data, 33 Image creating, 168 Immunity to interference, 41 Installation Drivers, 64 Memory modules, 122 Installation information, 34 Integration Ethernet, 57 PROFIBUS, 57 Interface, 58 MPI/DP interface, 58 USB, 75 Interfaces assignment on the motherboard COM2 (X31), 220 Internal interfaces, 227 Interrupt reaction time, 246 IT communication, 57 K Key code, 196 Key panel, 23, 93 Keyboard Features, 260 K
Index O On / Off switch, 91 Open Device, 119 Operating, 102 Touch panel, 102 Operating status, 24, 91 Operating system Updates, 167 Windows 2000, 161 Windows XP, 161 Windows XP Embedded, 164 Windows XP Professional, 157 Operating systems, 27 Output voltage, 194, 195 P Package contents, 32 Checking, 32 Packaging, 32 Checking, 32 Removing, 32 Panel PC 677B, 208 Panel Wizard Start screen, 64 starting, 64 Partitioning Hard disks, 159 Windows XP Embedded, 164 Windows XP Professional, 164 Partitions Hard disks,
Index Battery, 137 Restore DVD, 154, 156 Restoring factory state, 155 RJ45 Ethernet, 216 S Safecard On Motherboard Temperature monitoring, 106 Safety information, 16 SATA Port, 256 SATA/PATA Configuration, 266 Scope, 11 Screen size, 65, 68 Self-test, 62, 78 Separating Device, 115 Shipping, 22 ESD, 22 SIMATIC S7, 57, 58 Integration, 57 Slide-in labels, 28 Softkey, 100 labeling, 100 Softkey row, 100 Software, 19 SOM, 91, 106 Spare parts, 113 Special codes, 176 Standard, 11 Start screen Panel Wizard, 64 Stat
