User Guide ITP-5012L This manual contains information that is proprietary to SAMSUNG Electronics Co. Ltd. and is protected by copyright. No information contained herein may be copied, translated, transcribed or duplicated for any commercial purposes or disclosed to third parties in any form without the prior written consent of SAMSUNG Electronics Co. Ltd.
COPYRIGHT This manual is proprietary to SAMSUNG Electronics Co., Ltd. and is protected by copyright. No information contained herein may be copied, translated, transcribed or duplicated for any commercial purposes or disclosed to third parties in any form without the prior written consent of SAMSUNG Electronics Co., Ltd. TRADEMARKS OfficeServ ITP-5012L is the trademark of SAMSUNG Electronics Co., Ltd.
ABOUT THIS GUIDE This User guide provides instructions for the use of Samsung’s latest ITP-5012L large LCD IP Phone that can be used in connection with the Samsung’s Enterprise IP Solutions OfficeServ System. Please take the time to study this guide to become familiar with the operation of your ITP5012L phone and the benefits this new IP technology can provide. Keep this guide handy. You may need to look up instructions for infrequently used features.
ABOUT THIS GUIDE This page is intentionally left blank. Page II © SAMSUNG Electronics Co., Ltd.
SAFETY CONCERNS For product safety and correct operation, the following information must be read before the installation and operation of your ITP-5012L IP phone. Symbols Caution Indication of a general caution Restriction Indication of a prohibited action when using the product Instruction Indication of a required action © SAMSUNG Electronics Co., Ltd.
SAFETY CONCERNS WARNING The ITP-5012L IP phone shall be connected to the local AC power using the power adaptor provided with the IP phone. Use of an alternative adaptor may result in serious damage and voids the product warranty. The handset receiver on the IP Phone may retain metallic objects. Care should be taken when using the handset in the vicinity of small metal objects. Avoid placing objects containing water such as vases, cups, cosmetics, and medicines near the phone.
SAFETY CONCERNS Do not install the phone near a heater or naked flames (cigarette lighter, heating apparatus, etc.). It may cause a fire or electric shocks. Do not use flammable solvent or materials near the phone. Do not store them near the phone. It may cause a fire or electric shocks. If the phone makes excessive noise, emits an odour, or smoke, immediately unplug the phone and call your Authorised Samsung Reseller. © SAMSUNG Electronics Co., Ltd.
SAFETY CONCERNS CAUTION Be careful not to connect the network LAN cable to the PC connection port. If the LAN cable connected to network is connected to the PC connection port, both telephone and PC communications will be disabled. Use a soft dry cloth to clean the phone. Do not use any chemical solvents like wax, benzene, alcohol, thinner, aerosols, lubricant, or detergent. The use of chemicals on the phone may cause fading/discoloring or damage to the parts. Do not place heavy things on the phone.
TABLE OF CONTENTS ABOUT THIS GUIDE Conventions.......................................................................................................................... I SAFETY CONCERNS Symbols .............................................................................................................................. III Warning...............................................................................................................................IV Caution .......................................
TABLE OF CONTENTS Background Screen ........................................................................................................... 13 Executive Status Display ................................................................................................... 13 Application Menu Screen................................................................................................... 13 3. Using the Programmable Feature Screen.....................................................................
TABLE OF CONTENTS MAKING A CALL 1. Before Making a Call................................................................................................................... 33 Dialling Modes ................................................................................................................... 33 Calling Methods ................................................................................................................. 34 2. Making an lntercom Call.........................................
TABLE OF CONTENTS ANSWERING A CALL 1. Before Answering a Call............................................................................................................. 53 Call Answering Methods .................................................................................................... 53 2. Answering an Intercom Call ...................................................................................................... 54 Answering a Ringing Intercom Call .....................................
TABLE OF CONTENTS CONVENIENT FEATURES 1. Call Forwarding............................................................................................................................ 69 Forward All Calls................................................................................................................ 69 Forward Busy..................................................................................................................... 70 Forward No Answer ..........................................
TABLE OF CONTENTS 5. Executive/Secretary Hot Line.................................................................................................... 87 Executive Status Display ................................................................................................... 87 Call Transfer from Secretary to Executive......................................................................... 88 Executive/Secretary Message ...................................................................................
TABLE OF CONTENTS 3. Phone Book................................................................................................................................ 102 Search By Speed Dial Number Location ......................................................................... 102 Search a Telephone Number By Name........................................................................... 103 Search By Telephone Number.........................................................................................
TABLE OF CONTENTS Handset Volume .............................................................................................................. 129 Speaker Volume .............................................................................................................. 129 BGM Volume.................................................................................................................... 130 Page Volume ..........................................................................................
PREPARATION 1. Main Features IP Network The ITP-5012L IP phone provides voice communication through the previously installed data network line, making installation of additional telephone lines unnecessary. Network Large LCD Screen Displays various kinds of information, and you can simply press the related [Select] button next to the feature/menu. This feature provides easy search and selection of menus and features.
PREPARATION Pickup You can answer a call at another extension. Automatic Redial/Retry When your call is important but your party is busy on another call you can use automatic redial/retry function. The IP phone redials the called number automatically until your party is free to take your call. Hold Hold You can use the Hold function when you need something or another call is arrives. Use this button to temporally hold the current call until you are ready to resume the call.
PREPARATION Do Not Disturb When you do not want to be disturbed, the DND feature can be set to block incoming calls and the phone will not ring. Your calls can be forwarded to another station when you cannot be disturbed. Page If you have an urgent announcement to make, or you wish to locate a colleague, you can page through the speaker of other stations, or through optional external speakers.
PREPARATION 2. Checking the Parts in the Package Handset LAN Cable (for PC connection) ITP-5012L Phone Stand User Guide Power Adaptor (The view of power adaptor and power input specification may vary for each country.) - Please contact your Authorised Samsung Reseller if any item above is missing or damaged. NOTE Page 4 © SAMSUNG Electronics Co., Ltd.
PREPARATION 3. Name and Features of the ITP-5012L IP phone Front Panel Select Buttons LCD Panel Status Indicator Speaker Select Buttons Screen Button Volume Button Scroll Key Conference Button Transfer Button Dial Buttons Speaker Button Hold Button Microphone © SAMSUNG Electronics Co., Ltd.
PREPARATION Name and Features of Each PartEMBED [Select] buttons You can simply press the [Select] button next to the preferred item on the LCD panel. LCD Screen The LCD screen consists of the Status screen and the Main screen. ! The Status screen on the top of the LCD screen indicates using icons the status of your phone features.
PREPARATION Conference Button This button is used to connect multiple callers in a conference call. Transfer Button This button is used to transfer a call to another station or to access your station’s programming options. Navigation Buttons You can easily check the phone Application menus(Phonebook, E-Diary, Message, Volume, Forward, Config, and My Phone) with an icon or menu on the LCD screen. Microphone The microphone when in speakerphone mode and is located under the Navigation buttons.
PREPARATION Bottom Panel of the ITP-5012L Grooves for mounting the desktop stand LAN connection port PC connection port Power adaptor connection port Handset connection port Recording device Connection port LAN connection port Connect the LAN cable connected to the network to this port. PC connection port Connect the LAN cable connected to your PC’s network card to this port. Power adaptor connection port Connect the power adaptor plug to this port.
PREPARATION 4. Assembling the ITP-5012L IP phone Connecting lines to the phone 1. Connect the handset to the handset connection port. 2. Connect the LAN cable connected to the network to the LAN connection port at the bottom panel of the IP phone. 3. Connect the LAN cable connected to the PC’s network card to the PC connection port at the rear of the IP phone. 4. Connect the power adaptor. There is a power connection port for the power adaptor at the rear of the IP phone.
PREPARATION Using the Desktop Stand If the phone needs to be used in a desktop environment, insert the desktop stand into the two side holes, which are located at the rear of the phone, and push it in the upward direction, as shown in Figure below. Page 10 © SAMSUNG Electronics Co., Ltd.
THINGS YOU SHOULD KNOW 1. About Stations and Trunk Lines A station is a digital or IP phone or standard telephone connected to the OfficeServ system. A Trunk line is directly connected to your phone company’s telephone network. It allows you to make telephone calls to parties outside your office(for example, your home) or to received incoming calls from external parties. © SAMSUNG Electronics Co., Ltd.
THINGS YOU SHOULD KNOW 2. Introduction of Main Screens The main screens displayed on LCD of this IP phone are as follows. Programmable Feature Screen The programmable feature screen appears when the [Screen] button is pressed in standby mode or during a call. In this screen, the various features programmed in the telephone system are displayed such as speed dial keys or station keys. You can use these features by pressing the [Select] button for each feature.
THINGS YOU SHOULD KNOW Background Screen This is the default screen that appears in standby mode. ! You can use the ‘My Phone’ menu in the application menus to change this background screen. Refer to the Application Menus section. Executive Status Display This screen appears when the [Screen] button is pressed three(3) times during standby mode.
THINGS YOU SHOULD KNOW 3. Using the Programmable Feature Screen In this screen, the various features programmed in the telephone system are displayed such as speed dial keys. You can use the features by pressing the associated [Select] button. 1. When the telephone is in standby mode or Screen during a call, press the [Screen] button until the programmable feature screen is displayed. 2. Press the [Select] button of the required feature from the displayed features.
THINGS YOU SHOULD KNOW 4. Using the Soft Menu Screen In the Soft Menu screen, the various features that can be used during the setup of a call or during standby mode are displayed. You can use those features by pressing the associated [Select] button. 1. When the telephone is in standby mode or Screen during a call, press the [Screen] button until the Soft menu screen is displayed.
THINGS YOU SHOULD KNOW 5. Choosing a Function Because various features of this IP phone are displayed on the LCD screen, you can press the [Select] button corresponding to the desired feature or dial the desired function code. Refer below. The features available during a call are displayed on the LCD screen. Press the [Select] button of the desired function.
THINGS YOU SHOULD KNOW 6. Using a Function Code Many of the OfficeServ system functions can be invoked by dialling function codes. Please refer to the table below for the default function codes(these maybe changed in your system, refer to your System Administrator.).
THINGS YOU SHOULD KNOW 7. Entering Characters Using the dial buttons and the navigation buttons of this phone, you can easily enter/edit, letters, numbers and special characters. Selecting an Input Mode When the input screen appears, press the [Menu] button until the required input mode is selected.
THINGS YOU SHOULD KNOW EMBEDEntering Letters of the Alphabet 1. Press the [Menu] button to select the alphabet input mode. Use the direction button to move a cursor. 2. Then, press the dial buttons to modify or insert the desired letters. If the letter to enter is the same as the previous character, press the direction button to move the cursor one space to the right or wait until the cursor moves automatically after a 3 second delay. The location of alphabet letters on dial buttons is as follows.
THINGS YOU SHOULD KNOW Entering Special Characters 1. Press the [Menu] button to select the special character input mode. 2. Then, the special characters that can be selected will be displayed on the lower part of the character input screen. Press direction button, to select the special characters and press the [Enter] button. or Press NOTE direction button to select another type of special characters. - Press the dial button [0] to insert a blank.
THINGS YOU SHOULD KNOW 8. Volume Adjustment [!Volume"] button is used for adjusting the volume of the handset, speaker, and ringer. Adjusting Handset Volume 1. During a call using the handset, press the [Volume" "] button to increase the handset volume. 2. Press the [! !Volume] button to decrease the handset volume. Adjusting Speaker Volume 1. During a call using the [Speaker] button, press the [Volume" "] button to increase the speaker volume. 2.
THINGS YOU SHOULD KNOW Adjusting Ring Volume 1. To increase the ring volume, press the [Volume" "] button while the phone is ringing. 2. To decrease the speaker volume, press the [! !Volume] button while the phone is ringing. - In order to set the required volume of the various options for this IP phone, refer to the ‘Volume Menu’ of ‘Application Menus’ described in this guide. NOTE Page 22 © SAMSUNG Electronics Co., Ltd.
THINGS YOU SHOULD KNOW 9. Types of Signal Tone The types of signal tone used in this telephone system are described in the following table. Signal Usages Signal Interval Tone Name Dial tone Ring back tone A steady tone that indicates you can begin dialling. Indicates the station you dialled is ringing. Busy tone Indicates the station you dialled is busy. Transfer tone Indicates your call is being held and you can dial another station.
THINGS YOU SHOULD KNOW 11. Telephone Status Indicator The status indicator turns on or off according to the telephone status. Situation Status Indicator Busy Steady red. Station Ring Flashing red. Trunk Ring Flashing blue. Recall Ring Flashing purple. Message Camp On Flashing red. DND Fast flashing red within 1-second interval. 12. Button LED The [Transfer] button, [Hold] button, and [Speaker] button have a LED that turns on or off according to the phone status.
GETTING STARTED This chapter describes the procedure for setting the user environment after installing and booting the ITP-5012L IP phone. 1. Entering the Environment Setup Mode When the IP phone is first installed or the system settings have changed, you must set the data network environment settings through the environment setup menu. This menu also allows you to designate the TFTP server for upgrading the IP phones programs. 1. Connect the power adaptor while pressing the [Menu] button. 2.
GETTING STARTED 2. Editing The buttons and functions below are used for selecting a menu from the LCD screen and entering/cancelling/saving a value. Moving between Menus ! Press the [ ]/[ ] direction button to move to a menu and press the [Enter] button, or press the number of the menu using the dial buttons from [0] to [9]. ! Press the [Menu] button to move to the environment setup main menu. ! Press the [End] button to move to the previous menu without saving the entry.
GETTING STARTED 3. Network Settings You can verify or change the network environment. 1. Use the [ ]/[ ] button to move to the [2. Network] menu and press the [Enter] button. 2. Move to the [1. Mode] submenu and press the [Enter] button. 3. Select [1. Manual IP] menu to directly enter the phone’s IP address. " " Select [2. DHCP] to let your data network automatically allocate the IP address.
GETTING STARTED 5. The upper menu is displayed again. 6. Select [2. IP] to display the current IP address of the IP phone. No address is displayed if an IP address is not set. Use the dial buttons [0]~[9] and [ ] to enter a new IP address, and press the [Enter] button. " Be careful not to enter a duplicate IP address since the data network will not support duplicated IP addresses. 7. Select [3. Netmask] to display the current Netmask address of the IP phone.
GETTING STARTED 4. Load & Upgrade Settings You can verify or change the upgrade environment of the IP phone. 1. Use the [ ]/[ ] button to move to the [3. Load & Upgrade] menu and press [Enter] button. 2. The submenus are displayed. 3. Select [1. Load Option] and designate the source of program for the IP phone. " " Select [1. File System] to operate programs saved in the IP phone flash memory. Select [2. TFTP down run] to download programs saved in the TFTP server to the RAM memory of the IP phone.
GETTING STARTED 4. The [2. Upgrade Program] menu is used for upgrading the phone’s program. Enter the IP address of the TFTP server from which the program should be downloaded. Press the [Enter] button to start the program download process. If the correct TFTP server IP address is programmed press [Enter] to start the download process. 5. The [3. Upgrade Bootrom] menu is used for upgrading the phone’s Bootrom.
GETTING STARTED 5. Setting System Authentication Information This function is used to set the IP address of the OfficeServ system connected to the IP phone and the authentication ID and password of the IP phone. The ID and password of this menu are used when initially setting the IP phone and are not required while using the functions of the IP phone. If a function of the IP phone(such as Lock) requests a password, enter the system password set the Config/Password menu. 1.
GETTING STARTED 6. Verifying Settings You can verify the IP phone settings after setup. Incorrect settings can be adjusted after verification. 1. Use the [ ]/[ ] button to move to the [1. Information] menu and press the [Enter] button. 2. The submenus are displayed. Select each menu and verify the settings. Check, the [2. Network] menu settings are correct before using the IP phone. 7. Exiting Setup This option will exit the environment setup menu and reboot the IP phone. 1.
MAKING A CALL 1. Before Making a Call The calling methods and features are summarized in the following table. The detailed description corresponding to each feature then follows.
MAKING A CALL Calling Methods " Using a handset This function allows you to lift the handset and make a call. " Using a speakerphone This function allows you to make a call through the speakerphone without lifting the handset. Page 34 © SAMSUNG Electronics Co., Ltd.
MAKING A CALL 2. Making an Intercom Call This function is used when you want to make a call to other stations. Calling Other Stations 1. Lift the handset. 2. Dial the extension number of the other party. ! Or, press the [Select] button corresponding to the extension number in the programmable feature screen. 3. Press the [Send] button and ring tone will be heard. ! If beep tones are heard, without ring tone, the station you called is set for a voice announcement or an automatic answer function.
MAKING A CALL Busy Station Callback When you call another station and receive a busy signal, this function allows you to set a callback reservation for when the other station becomes free. 1. When another station is called and a busy tone is heard, press the [Select] button corresponding to [CALLBACK] displayed on the LCD screen. 2. Replace the handset after confirmation tone is heard. 3. When the busy station becomes free, your phone will ring.
MAKING A CALL Busy Station Camp-On When you call another station and receive a busy signal but you do not want to wait for a callback, this function allows you to camp on to the busy extension. 1. After calling a busy station, press the [Select] button corresponding to the [CAMP ON] displayed on the LCD screen. 2. The called station will receive off-hook ring tone repeated every few seconds to indicate that your call is waiting. 3. Wait for the called party to answer.
MAKING A CALL 3. Making an Outside Call Making an Outside Call 1. Lift the handset and dial the trunk access code [0] and then dial the telephone number of outside party. ! Or, press the [Select] button corresponding to the trunk line required in the programmable feature screen and dial the outside telephone number. 2. Press the [Send] button to make the call. 3. Begin speaking after the other party picks up the phone.
MAKING A CALL Redial This function allows you to redial the last external number dialled. 1. When the phone is in standby mode, press the [Screen] button repeatedly until the Soft menu screen appears. ! Or, dial [1][9], the function code for redial, and then press the [Send] button. 2. Press the [Select] button corresponding to [LAST REDIAL] displayed on the Soft menu screen. 3. Begin speaking after the other party picks up the phone. © SAMSUNG Electronics Co., Ltd.
MAKING A CALL Automatic Redial After making an outside call and receiving busy tone, your IP phone can redial the called number automatically. It can redial up to 99 times at a the preprogrammed interval. 1. Upon hearing a busy tone, press the [Select] button corresponding to the [Retry]. 2. The system reserves the line and redials the same number automatically. You can hear the call setup tones through the speaker. At this time, the microphone is automatically disabled. 3.
MAKING A CALL Busy Line Queuing With Callback If you receive a busy signal when selecting an outside line, this means that the line or group of lines is busy. This callback function allows a call to be placed in queue waiting for a free outside line. 1. If busy tone is heard when selecting a trunk line, press the [Select] button corresponding to [CALL BACK] displayed on the LCD screen. 2. Replace the handset after the confirmation tone is heard.
MAKING A CALL Making a New Call This function allows you to disconnect the existing call and make a new call on the same line. 1. While on a call, press the [Select] button corresponding to [NEW] menu displayed on the LCD screen. This will disconnect the current call and provide dial tone. 2. Dial an outside telephone number and press the [Send] button. Call Park This function allows you to place a call in a ‘parking orbit’ and announce the call over a paging system for someone to pick up.
MAKING A CALL 3. Dial the orbit number(0~9) to park the call and announce the orbit number for the required party to answer the call. 4. To retrieve a parked call press the [Select] button corresponding to [PARK] on the Programmable feature screen and dial the orbit number. NOTE About the Call Park and Orbit ‘Call Park’ means that you can park a call to allow someone to pick it up at another location. The storage places are called ‘orbits’ and there are a total of 10 orbits.
MAKING A CALL Using an Account Code The OfficeServ system can be programmed to force an account code entry prior to making outside calls or at anytime during the call if it is not forced. This allows the system to report calls against specific account codes in the call details report. 1. For forced entry of account codes, lift the handset and press [Send] in Enbloc dialling mode or lift the handset in Overlap dialling mode. 2. Press the [Select] button corresponding to [ACCT] on the screen.
MAKING A CALL Saving the Telephone Number You can save the current dialled outside number for later use and redial the number. Press the [Select] button for [SAVE/REPEAT] before hanging up the call, to save the phone number that has just been called. Redialling the Saved Number You can redial the saved number anytime. Press the [Select] button for [SAVE/REPEAT] in the Soft Menu screen or dial [1][7]. ! [1][7] is the function code for redialling the saved number.
MAKING A CALL Dialling from your Recent Call Log 1. Press the [Send] button briefly while in standby mode. ! If the [Send] button is pressed and held about 2 seconds, you can redial the last number dialled. 2. Up to 60 numbers of recently made or received calls will be listed in the order they were dialled/received. An icon to the left of each number will indicate whether it was an outgoing or an incoming answered or missed call. 3.
MAKING A CALL Speed Dialling The OfficeServ system can store up to 500 frequently dialled telephone numbers in the system speed dial list. In addition you can have up to 50 personal speed dial numbers stored in the system. ! You can dial a preprogrammed telephone number stored in the system-wide speed dial list of numbers 500-999 or from your personal list of numbers 00-49. 1. When the phone is in standby mode press the [Screen] button repeatedly until the Soft menu screen appears.
MAKING A CALL Dialling from the Directory Name The OfficeServ system maintains an online directory for extensions, system and personal speed dial names. The extension number or the speed dial number can be selected from the directory name list, which is in alphabetical order. 1. When the phone is in standby mode, press the [Screen] button repeatedly until the Soft menu screen appears. ! Or, press the [Speaker] button. 2. Press the [Select] button for the [DIRECTORY] menu. 3.
MAKING A CALL Conference Call Up to 5 members, including you, can participate in a conference simultaneously. 1. Press [Conference] button in the standby mode. 2. Press the [Select] button for [Group] in the conference screen to display the group list. 3. Press the left [Select] button of the entry box and enter the phone numbers of the participants. And press the [Enter] button. ! To save the entered phone numbers in the group, press the [Menu] button.
MAKING A CALL Conference Groups You can establish a conference simply by selecting one of 5 possible groups and the conference will be setup automatically. You can also review and edit the members of each group. 1. Press the [Conference] button in the standby mode. 2. Press the [Select] button for [Group] in the conference screen to display the group list. ! You can load or delete a number in the group by moving to the group and pressing the [Menu] button.
MAKING A CALL To establish a new Conference Group 1. Press the [Conference] button in the standby mode. 2. Press the [Select] button for [Group] in the conference screen to display the group list. 3. Press the left [Select] button of the entry boxes and enter the phone numbers of the participants. Press the [Enter] button after each participant to activate each member. ! Each activated member is indicated by a black Square in the entry box on the right hand side of the conference screen. 4.
MAKING A CALL This page is intentionally left blank. Page 52 © SAMSUNG Electronics Co., Ltd.
ANSWERING A CALL 1. Before Answering a Call The call answering methods and features are summarized in the following table. If you want to learn how to use each feature, please refer to the detailed description corresponding to each feature.
ANSWERING A CALL 2. Answering an Intercom Call Answering a Ringing Intercom Call 1. When the phone rings, a call receipt message will be displayed on the LCD screen. 2. Lift the handset and the ringing call will be automatically connected you. 3. Replace the handset after a conversation is over. Answering Using the Speakerphone ! Press the [Send] button, without lifting the handset. ! Listen to the speaker to hear a voice of the other party and speak through the microphone.
ANSWERING A CALL Automatic Answering Mode This function allows you to answer a station call on your phone where the intercom answering mode has been programmed for automatic answer. " Please refer to the ‘Setting the Answering Mode’ section in the ‘Configuration’ part of ‘Application Menus’ described in this guide. 1. When an incoming call arrives, beep tones will be heard and then the station automatically answers the call. 2. The speakerphone is turned on and you can speak hands-free.
ANSWERING A CALL 3. Answering an Outside Call Answering an outside call 1. When the phone rings, a call receipt message will be displayed on the LCD screen. 2. Lift the handset and the ringing call will be automatically connected. 3. Replace the handset after a conversation is over. To Answer using the Speakerphone ! Press the [Send] button, without lifting the handset. ! Listen to the speaker to hear a voice of the other party and speak through the microphone.
ANSWERING A CALL Universal Answer for Outside Calls The Universal answer feature allows you to answer outside calls programmed to ring a general alerting device such as a night bell. The Universal Answer feature does not apply to intercom calls. 1. If an outside call rings the alerting device. 2. Press the [Screen] button repeatedly until the Soft menu screen appears. " Or, dial [6][7], the function code for universal answer. 3. Press the [Select] button for [UNIV.
ANSWERING A CALL 4. Answering Calls at Other Extensions The functions below describe the methods available to answer calls ringing at unattended stations. Station Call Pickup 1. When you hear an unattended ringing station Lift the handset. 2. Dial [6][5], the function code for call pickup. 3. Dial the extension number of the ringing phone. Page 58 © SAMSUNG Electronics Co., Ltd.
ANSWERING A CALL Group Call Pickup Allows you to pick up a call ringing in any pickup group. Use group pickup when you and the ringing extension are part of a pickup group. 1. When a telephone assigned in the same pickup group is ringing, you can lift the handset. 2. Dial [6][6], the function code for group call pickup. 3. Dial the group number(01~20). NOTE - Station and group call pickup features may not be able to answer calls recalling to a station.
ANSWERING A CALL Answering a Waiting Call When currently on a call and a second call arrives from another station/outside caller this feature allows you to answer the waiting call. 1. Press the [Screen] button until the Programmable Feature screen appears. 2. Press the [Select] button for the Trunk flashing button in the Programmable Feature screen. " If an automatic hold feature is set up on your phone, the current call will be placed on hold automatically, otherwise it will be disconnected. 3.
FEATURES USED DURING A CALL 1. During an Intercom Call Features that can be used conveniently during an intercom call are described below. Hold an Intercom Call You can put the other party on hold if another call arrives or you wish to use both hands for another task and resume the call later. 1. Press [Hold] button and replace the handset to put the current call on hold. ! The intercom call is placed into exclusive hold and cannot be retrieved at another station. 2.
FEATURES USED DURING A CALL 2. During a Outside Call Features that can be used conveniently during an outside calls are described below. Hold an Outside Call You can put the other party on hold if another call arrives or you wish to use both hands for another task and resume the call later. 1. Press [Hold] button and put the call on hold. 2. Press the [Screen] button until the Programmable Feature screen is displayed. 3.
FEATURES USED DURING A CALL Hold a Outside Call and Make an Intercom Call You can put the outside caller on hold and call another station to consult with another staff member. 1. Press [Transfer] button. The caller will be placed on-hold. 2. Dial the station number. 3. Commence conversation with the recipient of the station call. 4. Press [Transfer] button to reconnect to the outside call on hold. - You can switch between the outside caller and the internal party by pressing the [Transfer] button.
FEATURES USED DURING A CALL Call Transfer While on an outside call you can transfer the call to another internal or outside party. 1. Press [Transfer] button during the call. 2. Dial the station/outside number to which the call should be transferred. 3. Press the [End] button or replace the handset to immediately transfer the call or wait for the called party to answer and announce the transfer before disconnecting the call.
FEATURES USED DURING A CALL Transfer to the Voice Mailbox You can automatically transfer the incoming call to the voice mailbox. The OfficeServ system should have the Samsung Voice Mail Service(SVMi) card installed. 1. When a call arrives, press the [Screen] button and then press the [Select] button for [VT] from the Programmable Features screen. 2. Dial the voice mailbox number. 3. The caller will be answered by the Voice mail card. Replace the handset or press [Speaker]. © SAMSUNG Electronics Co.
FEATURES USED DURING A CALL 3. During Intercom/Trunk Line Calls Features that can be used conveniently during intercom/Trunk line calls are described below. Conference Up to 5 members, including you, can participate in a conference simultaneously. 1. Press [Conference] button while on a call. You will hear conference tone 2. Dial the number of the internal or external party you wish to add to the conference, wait for them to answer and press [Conference] again. 3.
FEATURES USED DURING A CALL Mute During a call you can mute the handset transmitter or microphone while still listening to the other party. 1. Press the [Select] button for [MUTE] displayed on the screen. 2. Press the [Select] button for [MUTE(OFF)] to clear the Mute function. © SAMSUNG Electronics Co., Ltd.
FEATURES USED DURING A CALL This page is intentionally left blank. Page 68 © SAMSUNG Electronics Co., Ltd.
CONVENIENT FEATURES 1. Call Forwarding When unable to take incoming calls you can forward your calls to another station, group of stations or an outside telephone number. You may also program a dedicated feature key for Forward All, Forward Busy, Forward No Answer or Forward Busy and No Answer in the Programmable Features screen. Call Forwarding can be set using the Application menu. Refer to the ‘Call Forwarding’ section of the ‘Application Menus’ in this guide.
CONVENIENT FEATURES Forward Busy You can forward incoming calls to another number when you are using the phone. 1. Dial [6][0][2] in the standby mode and dial the number to which all calls should be forwarded. ! [6][0][2] is the function code for Forward Busy. 2. Wait for the confirmation tone and hang up. ! The forwarding icon will be displayed on the top of the phone’s LCD panel to indicate Forward has been set.
CONVENIENT FEATURES Forward Busy/No Answer When the Forward Busy and Forward No Answer destinations are both set, you may enable both these options simultaneously. When you are busy, calls will be transferred to the number specified in Forward Busy destination. If you do not answer, the calls will be forwarded to the Forward No Answer destination. 1. Dial [6][0][4] in the standby mode. ! [6][0][4] is the function code for Forward Busy/No Answer. 2. Wait for the confirmation tone and hang up.
CONVENIENT FEATURES Forward Follow Me When you will be away from your phone for a while, e.g. in a conference room or another office, you can forward your incoming calls to a station where you are currently located. Alternatively you can redirect calls to another station to your own phone. This is called follow-me or remote call forwarding. 1. At the phone you are currently located near dial [6][0][6]. ! [6][0][6] is the function code for Follow Me. 2.
CONVENIENT FEATURES 2. Do Not Disturb (DND) This feature is used to block incoming calls. Setting/Cancelling DND 1. Press the [Screen] button until the Soft menu screen is displayed. ! Or, dial the DND setup code, [4][0][1]. 2. Press the [Select] button for [DND]. 3. Press the [Select] button for [SAVE] to set DND. ! Press the [Select] button for [CLEAR] to clear the DND setting. 4. The status indicator blinks to indicate that the DND mode is set. © SAMSUNG Electronics Co., Ltd.
CONVENIENT FEATURES 3. Paging This feature is used to broadcast announcements through the phone’s internal speaker and/or optional external speakers. Internal Page To broadcast through the station speakers. 1. Lift the handset. ! Or, press the Page function code [5][5]. 2. Press the [Select] button for [PAGE] displayed on the screen. 3. Dial the required external zone [1], [2], [3], [4] or [0] to page all internal zones. 4. Deliver the announcement after the confirmation tone.
CONVENIENT FEATURES External Page You can broadcast announcements through optional speakers in external areas(such as large offices, work areas and factories). Four(4) External zones are available plus all external zones. 1. Lift the handset. ! Or, dial the Page function code [5][5]. 2. Press the [Select] button of the [PAGE] menu displayed on the screen. 3. Dial the required external zone [5], [6], [7], [8] or [9] to page all external zones. 4. Deliver the announcement after the confirmation tone.
CONVENIENT FEATURES All Page Allows you to page through all station speakers in the internal zones and speakers in external areas. 1. Lift the handset. ! Or, press the Page function code [5][5]. 2. Press the [Select] button for [PAGE] displayed on the screen. 3. Dial [!] to page all internal and external zones. 4. Deliver the announcement after the confirmation tone. The announcement will be broadcasted through the speakers in all external and internal zones. 5.
CONVENIENT FEATURES Meet Me Page You can use page to find the recipient of a call. 1. Lift the handset. ! Or, dial the Meet Me Page function code [5][4]. 2. Press the [Select] button for [MEET ME PAGE] displayed on the screen. 3. Dial the page zone number(0~9). 4. After the confirmation tone advise the the person you require to dial [5][6]. 5. The ‘Please press ANSWER WAIT’ message is displayed on the screen. Press the [Select] button for [ANSWER WAIT]. ! or Press [Transfer] followed by [5][4].
CONVENIENT FEATURES 6. The ‘Wait until the recipient responds’ message is displayed. You should hold on to the handset until the recipient dials the page answer code([5][6]). 7. Once the recipient enters the page answer code([5][6]), the recipient will be automatically connected to you. Call Park and Page When you answer an outside call for another user not currently at their desk, you can park the call and page the required party. 1. Press the [Select] button for [PAGE] while the call is on line.
CONVENIENT FEATURES 4. Hang up by replacing the handset. ! If the parked call is not answered within a specified time, the outside call will recall your phone. Intercom calls cannot be parked or paged. Page Pickup To answer the parked call notified in the page. 1. Lift the handset and press the [Screen] button until the Soft menu screen is displayed. ! Or, dial the Connect Call function code [1][0] 2. Press the [Select] button for [PAGE PICKUP]. 3.
CONVENIENT FEATURES Off-Hook Voice Announce (OHVA) Allows you to make an announcement to another station currently on a call. This feature is useful when you have an urgent message to deliver to a station user. 1. Dial the busy station. 2. After hearing the busy tone, press the [Select] button for [OHVA]. 3. After the warning tone, deliver the announcement which will be heard through the handset or the speaker on the busy station.
CONVENIENT FEATURES OHVA Reject 1. While listening to OHVA, you can press the [Select] button for [REJECT] to disconnect the OHVA call and resume the original call. - OHVA is not applicable to phones that have the DND option enabled. - OHVA is applicable to intercom calls and transferred calls. NOTE OHVA Cancel After finishing the OHVA call, you can resume the original call that was on hold. 1.
CONVENIENT FEATURES OHVA Block You can use the OHVA Block feature to reject all OHVA calls. 1. Press the [Screen] button until the Soft Menu screen is displayed. 2. Press the [Select] button for [OHVA BLOCK] and then select [ON]. ! Press the [Select] button for [OFF] in the [OHVA Block] menu to cancel OHVA Block. Page 82 © SAMSUNG Electronics Co., Ltd.
CONVENIENT FEATURES 4. Messaging Leaving a Station Message You can leave your phone number as a message on stations that do not answer your call or are busy. 1. Press the [Screen] button until the Programmable Feature screen is displayed. ! Or, dial the message function number, [4][3]. 2. Press the [Select] button of the [MESSAGE] menu on the Programmable Feature screen. 3. Wait for the confirmation tone and hang up. - Leaving a message is only applicable to intercom calls.
CONVENIENT FEATURES Cancelling Station Messages You can erase station messages left on other stations or delete the messages left on the your station. 1. To erase station messages you left on other stations, dial [4][2] and dial the station number of the other station. ! [4][2] is the function code for Cancelling Messages. 2. Dial [4][2] and enter the your station number to delete all station messages left on your station.
CONVENIENT FEATURES Verify/Return/Delete Station Messages You can verify, return, or delete the station messages left on your phone. The status indicator will flash red when a message is left on your phone and the screen. icon is displayed on the 1. Press the [Screen] button until the Programmable Feature screen is displayed. 2. Press the [Select] button of the [MESSAGE] menu on the Programmable Feature screen. 3.
CONVENIENT FEATURES Programmed Messages EMBEDWhen you will be away from you desk you can leave an absence message to advise internal callers of your status. Internal callers will receive the message on their LCD screen when they call you. 1. Lift the handset and press the [Screen] button until the Soft Menu screen is displayed. ! Or, dial the Programmed Messages function code [4][8]. 2. Press the [Select] button for [STATUS MSG] on the Soft menu screen. 3. Dial the Programmed Message code.
CONVENIENT FEATURES 5. Executive/Secretary Hot Line Executive Status Display Available only on phones with the Executive/Secretary Hot Line feature programmed, this feature is used to display the in/out status of the executive or to conveniently set messages between the executive and secretary. ! An icon, indicating an executive or secretary, is displayed on the upper section of the LCD screen. 1.
CONVENIENT FEATURES Call Transfer from Secretary to Executive The programmed secretary station will receive calls for the executive first and transfer the calls to the executive. 1. After the secretary answers the call and verifies the nature of the caller’s business, the secretary presses the [Select] button for [BOSS] in the programmable features screen to notify the executive of the call. 2. The secretary replaces the handset to complete the transfer of the call to the executive.
CONVENIENT FEATURES Executive/Secretary Message Messages that are frequently exchanged between the executive and the secretary can be preset for convenient use. The [EXE/SECR MSG] menu is displayed in the Soft menu screen of the phone where the Executive/Secretary Hot Line is enabled. 1. In the standby mode, press the [Screen] button until the Soft menu screen is displayed. 2. Press the [Select] button for [EXE/SECR MSG] on the Soft menu screen. 3.
CONVENIENT FEATURES Entering the Executive/Secretary Message There are no preset messages when first using the Executive/Secretary Hot Line. Press the [Menu] button and enter the message. 1. On the [Select EXE/SECR MSG] screen, move to the item where the message should be entered and press the [Menu] button. 2. Move to the [Edit] menu and press [Enter] button. 3. Enter the message in the message entry screen. The message should be composed of 16 characters or less. 4. Press the [Enter] button to save.
CONVENIENT FEATURES 6. In/Out of Group If your phone is assigned to a station group, you can remove the phone from the group or reassign the phone into the group. If the phone is removed from the group, you will receive station calls but no new calls to the group number. 1. In the standby mode, press the [Screen] button until the Soft menu screen is displayed. 2. Press the [Select] button of the [IN/OUT GROUP] menu on the Soft menu screen. 3.
CONVENIENT FEATURES 7. Group Listening You can allow others to listen to your current conversation through the speaker while you are talking on the handset. Others can only hear the conversation since the microphone is disabled. 1. Press the [Select] button for [GROUP LISTEN] during the call. 2. The conversation is audible to others through the speaker. 3. To disable the speaker and resume a personal conversation, press the [Select] button for [LISTEN(OFF)].
CONVENIENT FEATURES 8. Caller ID (CID) Presentation The OfficeServ system can be set to display not only the number but also the name of the caller prior to answering a call. The presentation of the Caller Id is an optional service provided by your telephone company. CID Presentation is applicable to both ISDN and analogue PSTN lines. To activate the CID features you must have the feature keys programmed in you Programmable Feature key screen.
CONVENIENT FEATURES Storing the Caller Number to a Speed Dial Number The caller number can be stored in your personal speed dial number list. 1. Press the [Select] button for [STORE] menu displayed on the programmable features screen during the call. 2. The personal speed dial number where the caller number is saved is displayed on the screen. NOTE Page 94 - Least Cost Routing(LCR) should be set accordingly to dial the saved caller number.
CONVENIENT FEATURES Viewing the Caller ID of Calls Parked/on Hold You can verify the CID before answering a call that is parked or on hold. 1. When the phone is in the standby mode or in the middle of a call, press the [Select] button of the [INQUIRE] menu displayed on the screen. 2. Dial the Trunk line number displayed on the screen to verify the CID. The CID of the Trunk line number is displayed on the screen. 3.
CONVENIENT FEATURES 10. Door Phone Related Features When you phone is programmed to receive calls from the door phone you can answer a call without leaving your desk. If the optional electric door release is fitted you can also unlock the door from your phone. Answering the Door Phone 1. When a call is received from the door phone, your IP phone will receive three short bursts of ring consecutively. 2. Lift the handset or press the [Send] button to connect to the door phone. 3.
CONVENIENT FEATURES 11. Background Music If background music is available on your OfficeServ system, you can listen to the background music through your ITP-5012L phone’s speaker in standby mode. 1. Press the [Hold] button to listen to the background music. 2. Press the [Hold] button again to turn off the music. 3. You can adjust the volume using the [▼Volume▲] button. This does not affect the speaker volume. - Only the System Administrator can set and change the background music source.
CONVENIENT FEATURES This page is intentionally left blank. Page 98 © SAMSUNG Electronics Co., Ltd.
APPLICATION MENUS 1. Navigation Buttons Navigation buttons are provided for your convenience. Menu Button ! When the [Menu] button is pressed in the standby mode, the phones application menus are displayed as icons. - If the [End] button or [Speaker] button is pressed in the application menus, the phone automatically exits the menus. NOTE Send Button ! The phone is set to ‘Enbloc’ dialling mode as default. So, when you enter phone numbers, they can be reviewed before dialling.
APPLICATION MENUS Enter Button The Enter button is used in the menu mode to select or save the corresponding item. ! Direction button The Direction button is used to move between items or to edit the content. 1[ ç̈ ] button is used - To move the cursor upward. - To select the main menu. 2[ è̈ ê̈ ] button is used - To select the Phonebook menu. - To move the cursor to the right. 3[ é̈ ] button is used - To select the Ring Type/Volume menu. - To move the cursor downward.
APPLICATION MENUS 2. Entering Application Menus When the IP phone is in the standby mode, press the [Menu] button. The main application menu will appear on the LCD screen. Selecting Application Menus ! Use the direction button to move to the desired application. Then, press the [Enter] button. ! Dial the corresponding to the number of the required menu item. (P-Book[1], E-Diary[2], Message[3], Volume[4], Forward[5], Config[6], My-Phone[7]) ! Press the [End] button to exit the application menus.
APPLICATION MENUS 3. Phone Book Press the Right direction button to enter the Phone Book menu OR Press the [Menu] button and use the direction button to select press the [Enter] button. Then, Search By Speed Dial Number Location This function allows you to search any telephone number based on the speed dial number locations registered in the IP phone. 1. Press the button and use the direction buttons to select " [1. Search] " [1. By Speed Dial No]. Then, press the [Enter] button. 2.
APPLICATION MENUS 3. The telephone number corresponding to the entered speed dial location is displayed. # If you press the [Enter] button without entering the speed dial number location, a list of all speed dial names programmed will be displayed. 4. Press the [Send] button to dial the selected telephone number. # Press the [Menu] button to change or disable the speed dial number. When the popup menu appears, select the desired menu to Edit/Delete/New Entry the number.
APPLICATION MENUS Search By Telephone Number You can search based on the telephone number or part of a telephone number registered in the IP phone. 1. Press the button and use the direction button to select " [1. Search] " [3. By phone number]. Then, press the [Enter] button. 2. The screen that prompts you to enter a telephone number appears, enter the telephone number to search and press the [Enter] button. 3. The speed dial name(s) related to entered telephone number is displayed.
APPLICATION MENUS Search a Telephone Number By Group You can search for telephone numbers by groups registered in the IP phone. This will only work if you have allocated speed dial names and numbers to specific groups. Refer to Registering New Numbers and Editing Groups later in this section. 1. Press the button and use the direction button to select " [1. Search] " [4. By group]. Then, press the [Enter] button. 2.
APPLICATION MENUS Search a Telephone Number By Time You can search for any telephone number based on the time the telephone number was registered in the phone. Speed dial names will be displayed commencing with the latest entry. 1. Press the button and use the direction button to select " [1. Search] " [5. By time]. Then, press the [Enter] button. 2. The list of all the registered names is displayed, move to required name and press the [Enter] button.
APPLICATION MENUS Recent Called Numbers The call details and Calling line ID, if available, of up to the last 30 incoming calls will be saved in the incoming call log. You can review the details and dial the Caller ID. 1. Press the button and use the direction button to select " [3. Received Nos]. Then, press the [Enter] button. 2. Move to the desired telephone number and press the [Enter] button to review details about the call. 3. Press the [Send] button to dial the selected telephone number.
APPLICATION MENUS Telephone Number Registration You can save 1000 speed dial names and 2,400 telephone numbers. Each Speed dial name can have the following information registered : 5 telephone numbers(home, mobile phone, work/school, Etc, and facsimile), e-mail, group, and memo. Each speed dial number can also be allocated a speed dial number location. 1. Press the button and use the direction button to select " [4. New number]. Then, press the [Enter] button. 2.
APPLICATION MENUS Editing Groups This function allows you to establish groups to which speed dial names can be included. This allows you to search for speed dial numbers by personalized groupings. 1. Press the button and use the direction button to select " [5. Edit Group]. Then, press the [Enter] button. 2. The list of registered groups appears. 3. Press the [Menu] button to Add/Edit/Delete the group. (Group 1(Null) provides the option to ‘Add’ only.
APPLICATION MENUS Deleting All Telephone Numbers This function allows you to delete all saved telephone numbers and associated names. 1. Press the button and use the direction button to select " [6. Delete All]. Then, press the [Enter] button. 2. If the password entry screen appears, enter the password set in the IP phone. # If the password is not changed, the initial value of password is 1234. If you do not remember your password, please contact your System Administrator. 3.
APPLICATION MENUS 4. E-Diary Press the [Menu] button and use the direction buttons to select Then, press the [Enter] button. Move to the desired menu and press the [Enter] button. Wakeup Call Allows you to set an alarm to ring for 1 minute or until answered, at the required time. The frequency options for a wakeup call are ; everyday, Monday to Friday or Monday to Saturday. 1. Press the [Menu] button and use the direction button to select ! [1. Wakeup Call]. Then, press the [Enter] button. 2.
APPLICATION MENUS Alarm Clock This function is similar to the wakeup call function except that the frequency of the alarm is limited to once only or everyday. Two separate alarm times are available. 1. Press the [Menu] button and use the direction button to select ! [2. Alarm]. Then, press the [Enter] button. 2. Select [Alarm clock 1] or [Alarm clock 2]. 3. Set the Time, Ring, and Frequency of the selected alarm clock.
APPLICATION MENUS 3. Use the direction button to program the schedule items. Set the Date, Time, Message Contents, Alarm Timer(an hour before the set time, 30 minutes before the set time, or on time) and Ring type and press the [Enter] button. Adding/Modifying/Deleting the Schedule 1. Press the [Menu] button and use the direction button to select ! [3. Daily Planner]. Then, press the [Enter] button. 2. Use the direction buttons and select the date you require. Press the [Enter] button. 3.
APPLICATION MENUS Memo Pad Allows you to save a simple memo to the IP phone. Entering a Memo 1. Press the [Menu] button and use the direction button to select ! [4. Memo Pad] ! [1.Add New Memo]. Then, press the [Enter] button. 2. Enter the memo in the Memo screen and press the [Enter] button to save. " Please refer to the ‘Entering Characters’ section of ‘Things You Should Know’ in this guide for entering characters. Checking/Modifying/Deleting/Registering Memo 1.
APPLICATION MENUS Calculator A simple calculator is available to add, subtract, multiply, and divide numbers. 1. Press the [Menu] button and use the direction button to select ! [5. Calculator]. Then, press the [Enter] button. 2. Enter the numbers to calculate. Then, press the direction button to select the required operation. Enter the next number and press the [Enter] button to check the calculation results.
APPLICATION MENUS World Time Allows you to search local time in 39 cities around the world(Guam, New York, Dallas, Tokyo, Denver, Lapas, London, Rome, Miami, Moscow, Midway, Bangkok, Berlin, Buenos Aires, Beijing, Samoa, San Francisco, Seoul, Sydney, Chicago, Abu Dhabi, Athens, Alaska, Alma Tai, Oakland, Okhotsk, Wellington, LA, Jakarta, Middle Atlantic, Tashkent, Phoenix, Karakas, Cape Verde, Paris, Hawaii, Honolulu, Helsinki, and Hong Kong). 1.
APPLICATION MENUS D-DAY Plus D-DAY Plus allows you to enter an important schedule so that you can check the time left until or the time passed from, the entered date (D-Day). The D-DAY can be entered directly, or can also be entered automatically by calculating the number of days before/after the entered base date. Entering a New D-DAY 1. Press the [Menu] button and use the direction button to select ! [7. D-Day Plus] ! [1. D-Day Add]. Then, press the [Enter] button. 2. Select [1.
APPLICATION MENUS Unit Conversion This feature provides a simply conversion program for commonly used units of measurement for temperature, length, weight, volume, and area. 1. Press the [Menu] button and use the direction button to select ! [8. Units Convert]. Then, press the [Enter] button. 2. Use the direction button to select the desired unit. Then, press the [Enter] button. 3. Specify the value of each item(base unit, number to convert, and conversion unit) and press the [Enter] button. 4.
APPLICATION MENUS 5. Message Press the direction button to enter the Text Message menu OR Press the [Menu] button and use the direction button to select Then, press the [Enter] button. Move to the desired menu and press the [Enter] button. Received Messages Allows you to check text messages or set the status of message reception. 1. Press the button and use the direction button to select ! [1. Received]. Then, press the [Enter] button. 2.
APPLICATION MENUS Message Charge Allows you to review received text messages and to setup how you wish to be notified on the arrival of a new text message. 1. Press the button and use the direction button to select ! [1. Received] ! [1. Msg. Charge]. Then, press the [Enter] button. 2. Select a message from a list of messages and press the [Enter] button to see the message content. " If the message is long, press the direction button and display the rest of the message.
APPLICATION MENUS Setting Message Arrival Notice Interval You can set how your phone will notify you of a new text message. 1. Press the button and use the direction button to select ! [1. Received] ! [2. TextMsg.Setup] ! [1. Indi. Interval]. Then, press the [Enter] button. 2. Select the interval for notifying you of a new message arrival and press the [Enter] button. " " " Once : Alarm rings once when a message arrives. Every 2 Minutes : Alarm rings every 2 minutes until the message is checked.
APPLICATION MENUS Setting/Clearing Message Display Allows you to select whether to display the contents of the message when the message arrives. 1. Press the button and use the direction buttons to select ! [1. Received] ! [2. TextMsg.Setup] ! [3. Show Contents]. Then, press the [Enter] button. 2. Select whether to display the contents of the message when the message arrives and press the [Enter] button. " " Select [Save] to display the popup screen with the contents of the new message.
APPLICATION MENUS Writing a Message You can write and send a text message. 1. Press the button and use the direction buttons to select ! [2. Write & Sent] ! [1. Write Message] ! [1. Write New Message]. Then, press the [Enter] button. 2. Enter the phone number to receive the message as well as the message. Press the [Enter] button, to send the message. " " " Please refer to the ‘Entering Characters’ section of ‘Things You Should Know’ in this guide for entering characters.
APPLICATION MENUS Managing the Sent Message Box Allows you to check/delete/resend the sent or reserved messages saved in the Sent Message box. " Messages cannot be modified. 1. Press the button and use the direction buttons to select ! [2. Write & Sent] ! [2. Outgoing Message]. Then, press the [Enter] button. 2. Select the sent message required and press the [Menu] button. The selected message can be resent to another person or deleted.
APPLICATION MENUS Draft Allows you to retrieve and conveniently use messages saved as a Draft. 1. Press the button and use the direction buttons to select ! [3. Draft]. Then, press the [Enter] button. 2. Move from the Draft screen to the desired menu. Then, press the [Enter] button. New Draft Message Registration Allows you to write and register a new draft message for later use. 1. Press the button and use the direction buttons to select ! [3. Draft] ! [1. New Message].
APPLICATION MENUS Searching Messages Allows you to search your saved draft messages. 1. Press the button and use the direction buttons to select ! [3. Draft] ! [2. Search Message]. Then, press the [Enter] button. 2. Use the direction button to move to the message to be retrieved and press the [Menu] button. Then, you can send/modify/delete/delete all the draft messages or add a new message.
APPLICATION MENUS 6. Volume Adjustment Press the down direction button to enter the Ring type/Volume menu OR Press the [Menu] button and use the direction buttons to select Then, press the [Enter] button. Move to the desired menu and press the [Enter] button. Selecting a Ring Type Allows you to select a ring type for incoming calls. 1. Press the button and use the direction button to select ! [1. Ring type]. Then, press the [Enter] button. 2. There are 8 ring types.
APPLICATION MENUS Ringer Volume Allows you to set the volume of the ringer. 1. Press the button and use the direction button to select ! [2. Ringer]. Then, press the [Enter] button. 2. There are 8 volume levels. Press the [▼Volume▲] button to set the volume. Off-hook Volume Allows you to set the volume of the Off-hook ring that that indicates a waiting call. 1. Press the button and use the direction buttons to select ! [3. OffHook Ring]. Then, press the [Enter] button. 2.
APPLICATION MENUS Handset Volume Allows you to set the volume when speaking through the handset. 1. Press the button and use the direction buttons to select ! [4. Handset]. Then, press the [Enter] button. 2. There are 8 volume levels. Press the [▼Volume▲] button to set the volume. Speaker Volume Allows you to set the volume of the speaker when using the phone in speakerphone mode. 1. Press the button and use the direction buttons to select ! [5. Speaker]. Then, press the [Enter] button. 2.
APPLICATION MENUS BGM Volume Allows you to set the Back Ground Music(BGM) volume when the BGM is set on the IP phone. " If BGM is not available on your phone refer to your System Administrator. 1. Press the button and use the direction buttons to select ! [6. BGM]. Then, press the [Enter] button. 2 There are 16 volume levels. Press the [▼Volume▲] button to set the volume. Page Volume Allows you to set the volume for received Page announcements. 1.
APPLICATION MENUS 7. Call Forwarding Allows you to forward your incoming calls to a specific extension, group of extensions or an external number when you are unable to receive an incoming call. # The call forwarding option may not be available to all stations, please consult with your System Administrator. 1. Press the [Menu] button and use the direction buttons to select Then, press the [Enter] button. 2.
APPLICATION MENUS 8. Configuration Press the [Menu] button and use the direction buttons to select Then, press the [Enter] button. Move to the desired menu and press the [Enter] button. Changing a Password Allows you to change your 4-digit password, which is used to protect your IP phone privacy or set a variety of IP phone features. Initial value of your password is 1234. " 1. Press the [Menu] button and use the direction buttons to select ! [1. Password]. Then, press the [Enter] button. 2.
APPLICATION MENUS Locking a IP phone Allows you to lock any outgoing trunk calls or incoming/outgoing calls to prevent others from using your IP phone without permission. 1. Press the [Menu] button and use the direction buttons to select ! [2. Locked]. Then, press the [Enter] button. 2. Enter the password of the IP phone. " " Initial value of password is 1234. If you do not remember your password, contact your System Administrator 3. Use the direction buttons to select the lock type required.
APPLICATION MENUS Setting the Boss Answering Mode Allows you to set the answering mode when you are called by a designated Secretary. Only applies if the IP phone is assigned with a boss function. If the Automatic mode or the Voice Announce mode is set, the call will be answered even if you are not present. 1. Press the [Menu] button and use the direction buttons to select ! [4. Boss Answering]. Then, press the [Enter] button. 2. Use the direction button to select the Boss answering mode.
APPLICATION MENUS Setting the Method of CID Display Allows you to set the type of Caller ID(CID) display on the LCD screen of the IP phone. 1. Press the [Menu] button and use the direction buttons to select. ! [6. CID Display]. Then, press the [Enter] button. 2. Use the direction button to select the type of caller ID display. Then, press the [Enter] button. " " " None : Caller IDs are not displayed. Name : If the name of a caller is registered in the [Phone Book], the name will be displayed.
APPLICATION MENUS Setting Absent Messages Allows you to set a message to be displayed to internal callers on their LCD screen if you are absent for a while. 1. Press the [Menu] button and use the direction buttons to select ! [7. Absent Msg.]. Then, press the [Enter] button. 2. Use the direction buttons to select the desired absent message and then, press the [Enter] button. The absent message will be set. 3.
APPLICATION MENUS Dial Mode Allows you to set the dial mode when making a call. In Enbloc mode which is set by default, you enter the phone number first and press the [Send] button to connect to the other party. In the Overlap mode, as you enter the phone number, the call connection will be made immediately. 1. Press the [Menu] button and use the direction buttons to select ! [9. Dial Mode]. Then, press the [Enter] button. 2. Use the Left/Right direction buttons to select the Dial Mode.
APPLICATION MENUS The functions which can be tailored to your individual requirements in Station ON/Off are: " " " " " " " " " " " " " " " " Page 138 AUTO HOLD : if ON an existing external call is automatically placed on hold if a CALL button, trunk button or trunk group button is pressed during call. For example to answer a second incoming call. AUTO TIMER : if ON, the stopwatch timer automatically starts during an external call.
APPLICATION MENUS 9. My Phone Press the [Menu] button and use the direction buttons to select Then, press the [Enter] button. Move to the desired menu and press the [Enter] button. Select BG Allows you to set the initial background screen on the LCD of your IP phone. 1. Press the [Menu] button and use the direction buttons to select ! [1. Select BG]. Then, press the [Enter] button. 2. Use the direction buttons to select the desired screen, and then press the [Enter] button. © SAMSUNG Electronics Co.
APPLICATION MENUS Entering the Name Allows you to enter your name to identify your IP phone. The entered name is displayed on the LCD screen of the caller’s phone during an internal phone call. 1. Press the [Menu] button and use the direction buttons to select ! [2. My Name]. Then, press the [Enter] button. 2. When the name input screen appears, enter a name of up to 11 characters and press the [Enter] button.
APPLICATION MENUS Viewing Status Information Allows you to check the feature status registered on your phone. 1. Press the [Menu] and use the direction buttons to select ! [4. Status Info]. Then, press the [Enter] button. 2. Displays the Call Forwarding, Absent Message, DND, and Lock status of your IP phone. Enbloc Timeout Allows you to set a valid time from entering a phone number to pressing the [Send] button when the dial mode of the IP phone is set to Enbloc. 1.
APPLICATION MENUS News Color Allows you to set the color of characters of OfficeServ News in the calendar screen. 1. Press the [Menu] button and use the direction buttons to select ! [6. News Color]. Then, press the [Enter] button. 2. Select ‘Light’ or ‘Dark’. " " Page 142 Light The black news characters are displayed on the white background screen. Dark The white news characters are displayed on the black background screen. © SAMSUNG Electronics Co., Ltd.
APPLICATION MENUS Privacy Option Allows you to restrict unauthorised access to the Application Menus on your phone. To access the Application Menus you must enter your phone is the privacy option is set. 1. Press the [Menu] button and use the direction buttons to select ! [7. Privacy Option]. Then, press the [Enter] button. 2. Enter your password, and select [Save] or [Clear]. Then press the [Enter] button to enable. Config. Reset Allows you to delete all saved data(Phone Book, Messages etc). 1.
APPLICATION MENUS Version Information Allows you to view the version of your phone. 1. Press the [Menu] button and use the direction buttons to select ! [9. Version Info]. Then, press the [Enter] button. 2. The version of your phone is displayed on the screen. Page 144 © SAMSUNG Electronics Co., Ltd.
ANNEX 1. Troubleshooting Possible problems and troubleshooting steps for your IP phone are described below: Check the troubleshooting steps before contacting your Authorised Samsung Reseller. ? The phone does not boot when the power is connected. ! Check to confirm the data network cable is connected to the LAN socket on the phone properly. ! Check to confirm the connected power adaptor was the one supplied with the ITP-5012L phone.
ANNEX ? Nothing appears on the LCD screen while the ITP-5012L phone is being used. ! Check the data network cable is correctly connected to the LAN socket on the ITP-5012L phone. (Refer to ‘Assembling the ITP-5012L IP phone’ section of ‘Preparation’ in this guide.) ? The ITP-5012L phone does not ring and volume is too low. ! Press the [▼Volume▲] button to adjust the volume. (Refer to ‘Volume Adjustment’ section of the ‘Things You Should Know’ section in this guide.
ANNEX ? An alarm does not ring at the programmed time. ! Check the current time is set on the ITP-5012L phone correctly. If the current time setting needs to be changed, contact your System Administrator. ! Check if an alarm is set. (Refer to ‘Alarm Clock’ in the ‘Application Menus/E-Diary’ section of this guide.) © SAMSUNG Electronics Co., Ltd.
ANNEX 2. Product Specifications The specifications and features of the ITP-5012L IP phone are as follows. Item Specification Model ITP-5012L Weight(kg) 1.1 Size(mm) 266(width) X 206(length) X 122(height) Operating Temperature(°C) Operating Humidity(%) 10 to 90 non condensing Ethernet 10/100BASE-T 2 Ports(LAN & PC) Dynamic Compression Modes G.711 and G.