Specifications

ManualsBrandsSiemens ManualsHome building and DecorFS-250

The FS-250C addressable fire alarm control panel is a

small, low cost fire alarm panel suited for stand-alone

operation in small to medium sized facilities. It features a

single addressable input device circuit and four notification

appliance circuits. The FS-250C is ULC Listed.

Main System

The FS-250C indicates alarm, trouble and supervisory

conditions with an 80 character backlit LCD display, as

well as a 20 zone/4 signal LED annunciator that is built in

to the Front Panel. Acknowledge, alarm silence and

system reset are accomplished with built-in membrane

control buttons. Basic user and maintenance level

functions such as viewing history or system enable/

disable are also accomplished through the membrane

control buttons. Password protection of maintenance

level functions is present. The main system can charge

up to 32 AH battery sets, up to 12 AH will fit inside the

enclosure.

The basic FS-250C features a single addressable signaling

line circuit (Class A or B) capable of supporting up to 252

addressable input devices, whether they are detectors,

manual pull stations, or contact monitoring points. Each

4306C

CATALOG NUMBER

• One intelligent signaling line circuit (DCLB + DCLA)

• SureWire Polarity insensitive loop wiring

• Utilizes S-Series detectors and devices

• Supports up to 252 addressable inputs and signal/relay

outputs

• Devices operate on standard wire, no twist or shield

required

• FirePrint application specific fire detection

• 4 Class B/2 Class A signal circuits

• Up to 6 amps of signal power

• Built in strobe synchronization protocol

• One man walk test (silent or audible)

• 80 Character backlit LCD display & 20 Zone/4 signal circuit

LED annunciation on Front Panel

• Optional internal DACT capable of transmitting point or

group information

• Programmable from front keypad or Windows based PC

configuration tool

• Single stage and 2-stage operation

• Alarm, pre-alarm, supervisory, trouble

• Auto program feature makes system start-up faster

• Maintenance and technician level passwords

• ULC Listed

FireSeeker Model FS-250C

Addressable Fire Alarm Control Panel

detector can also have an optional audible detector base,

relay detector base, or remote lamp associated with it.

These auxiliary devices are completely controlled through

logic and are not required to activate simultaneously with

the detector.The system also has four class B or 2 class

A Notification Appliance Circuits built into the main board.

Each circuit has a capacity of 1.5 amps of 24 VDC for

powering horns, strobes, chimes, and other notification

appliances. The total base system capacity for the four

circuits in 3.0 amps and can be expanded to 6A. Each

signal circuit is fully programmable and supports standard

and custom coded outputs of audible devices. Systems

can be configured to sound different codes on the same

signal circuit to indicate different conditions.

The FS-250C has four Form C relays on the main board

for monitoring alarm, pre-alarm, supervisory and trouble

conditions. Each relay is rated at 1 amp @ 28VDC.

Auxiliary 24VDC power is also available on the main

board, with a capacity of up to 0.4 amps.

Summary of content (14 pages)

PAGE 1
FireSeeker Model FS-250C Addressable Fire Alarm Control Panel • One intelligent signaling line circuit (DCLB + DCLA) • SureWire Polarity insensitive loop wiring • Utilizes S-Series detectors and devices • Supports up to 252 addressable inputs and signal/relay outputs • Devices operate on standard wire, no twist or shield required • FirePrint application specific fire detection • 4 Class B/2 Class A signal circuits • Up to 6 amps of signal power • Built in strobe synchronization protocol • One man walk test
PAGE 2
The Loop Programmable Relays The FS-250C utilizes the advanced CX-2 protocol for the detection circuit.The CX-2 loops features include SureWire™ technology providing, 252 addresses (inputs AND outputs), polarity insensitivity, response time under 3 seconds, retrofit installations using almost any type of wire (shielded, non-shielded, twisted, etc.) Programmable relays are available on the FS-250C. A remote processor board communicates with the main system board via an RS-485 communication network.
PAGE 3
s Fire Safety TXL-1008K Fire Alarm Control Panel ENGINEERS AND ARCHITECTS SPECIFICATIONS FEATURES • 8 Class B (Style B) Initiating Circuits which may be configured as 4 Class A (Style D) Circuits. • Expandable up to 24 Class B or 12 Class A Initiating Circuits • 4 Class A/B (Style Z/Y) Indicating Circuits with individual trouble indicators (1.7 Amps max. per circuit) • Each Indicating Circuit can be configured as Silenceable or Non-Silenceable.
PAGE 4
Description Application The Main Chassis also includes a 6 Amp Power Supply which powers the system and supplies two 4-wire resettable regulated smoke power supply of 24 VDC 200mA maximum each. The MCC-1024-6 also allows for the addition of two TSGM-1004 Signal Modules or two TRM-1008 Relay mdoules in place of the TDM-1008 Initiating Circuit Adder Modules.
PAGE 5
s Fire Safety TXL 1000 FIRE ALARM SYSTEM ENGINEERS AND ARCHITECTS SPECIFICATIONS Standard Features • Large system capacity • Modular design • Each Indicating Circuit can be configured as Silenceable or Non-Silenceable • Audibles may be configured as Steady, Temporal Code, California Code or March Time • Each Initiating Circuit can be configured as Alarm, Supervisory, Waterflow or Trouble • Two LEDs per Initiating circuit; one for Trouble and one for Status • Initiating and Indicating Circuits may be indiv
PAGE 6
Communicator and the TPR-100 Polarity Reversal / City Tie Module. Equipped with Configuration DIP Switches on the Main Display Module the TXL 1000 Fire Alarm Control Panels are configured through a combination of DIP switch and button settings. Through this configuration method the user can define the system as a Single Stage or Two Stage operation as well as perform various functions such as a One Man Walk Test.
PAGE 7
TBB-1024 TBB-1072 This enclosure is capable of handling one TMCC-1024-6 or TMCC-1024-12 Main Chassis and up to 17 AH Batteries. The TXL-1024TR Semi-Flush Trim Ring is required for flush mounting. The cabinet features a lock and a removable door for easy installation and servicing. The cabinet is available in a black colour. This enclosure is capable of handling one TMCC-1024-6 or TMCC-1024-12 Main Chassis and one TECH-1048 Expander Chassis as well as up to 40 AH Batteries.
PAGE 8
FireFinder XLS FireFinder XLS Fire Alarm Control Panel • Standard 2500 addressable point capacity system • Networkable to other FireFinder XLS systems • Powerful, easy-to-use programming capabilities • Fully Field Programmable Via Windows Laptop Computer • 6" Backlit LCD display • User-friendly system interface • Touch screen for maintenance operations and function keys • Multi-Language Display • Universal AC power input - 120/ 240VAC, 50/60Hz • 12 amps of system power, expandable to 48 amps • Numerous Rel
PAGE 9
Description The basic XLS control unit consists of the following subassemblies: PMI Person Machine Interface; PSC-12 Power Supply; DLC Device Loop Card; ZIC-4A Zone Indicating Card; CC-5 Card cage; ID-SP Inner Door Blank Single Plate; CAB-1, CAB-2 or CAB-3 enclosures.
PAGE 10
The NIC-C Card has diagnostic LEDs that indicate Card Fail, CAN Fail, HNET Fail, XNET Fail, Ground Fault, Loop A Fail and Loop B Fail, as well as LEDs to indicate Power, Style and Active Networks. ZIC-8B/ZIC-2C ZIC-8B/ZIC-2C The Zone Indicating Card ZIC-8B provides eight fully supervised programmable output circuits for use on the FireFinder XLS Fire Alarm Control Panel. The ZIC-8B supplies 8 Class B (Style Y) type output circuits, power limited to 2.0 amps maximum per circuit.
PAGE 11
rooms. Also, the CDC-4 can be used to upgrade Siemens conventional fire alarm panels to the FireFinder XLS system without requiring detector replacement. CRC-6 Controllable Relay Card CRC-6 Controllable Relay Card The Controllable Relay Card (Model CRC-6) is used with the FireFinder XLS Fire Alarm Control Panel. It is designed to provide auxiliary control of building functions such as door holder release, elevator capture, smoke control, lock release, etc.
PAGE 12
programmed usage. The label slides behind a clear protective membrane. One of the LED's assigned to each switch is a dual color LED used to indicate what type of signal is active. indicate Fan/Damper/Motor status: OFF (Red LED), ON (Green LED), TROUBLE(Yellow LED). Each SCM-8 and each switch is fully programmable and may be used to control speaker circuits, and awide range of general system functions such as All Call, All Evac, Warden's Page, Speaker, etc.
PAGE 13
SSD Series PSX-12 Power Supply Extender PSX-12 Power Supply Extender The PSX-12 is a high current auxiliary power supply that expands the FireFinder-XLS systems main PSC-12 power supply and battery charger with an additional 24VDC power. It is rated at 12Amps. RNI Remote Network Interface RNI Remote Network Interface The Model RNI Remote Network Interface provides a connection point for use with equipment mounted in a remote lobby enclosure on the FireFinder XLS Fire Alarm Control Panel.
PAGE 14
MDACT - Multi-Point Digital Alarm Communicator Transmitter MDACT - Multi-Point Digital Alarm Communicator Transmitter The Model MDACT Multi-Point Digital Alarm Communicator Transmitter is used in FireFinder XLS systems where point identification of alarm, supervisory, security and trouble events is required at Central or Remote Receiving Stations. An intelligent RS-485 communications protocol transmits all system information to the MDACT.