User Manual

ManualsBrandsSiemens ManualsIndicating unitsUniversal digital indicator BAU

CA1N5311E

10.2000

Siemens Building Technologies

Landis & Staefa Division

311

Universal digital indicator

BAU

for programmable input signal

Universal single point digital indicator

• suitable for front-mounting on control panels

• the type of signal, measuring range and engineering unit can be programmed

by use the DIP switches

• with liquid crystal display (LCD)

• for nominal voltage AV 24 V, 50 ... 60 Hz

Use

The BAU universal digital indicator is suitable for frontal mounting in control panels,

control panel doors or covers. It is normally used to indicate various programmable

input signals.

Functions

The type of signal, measuring range and engineering unit can be programmed by use

the DIP switches (see table on page 3). The measured value is displayed digitally. The

supply voltage and input signal for the indicator are electrically isolated by a built-in

isolating transformer.

Ordering

When placing order, please specify the quantity, product description and type code.

1 Universal digital indicator BAU

Example:

Summary of content (4 pages)

PAGE 1
5 311 Universal digital indicator BAU for programmable input signal Universal single point digital indicator • suitable for front-mounting on control panels • the type of signal, measuring range and engineering unit can be programmed by use the DIP switches • with liquid crystal display (LCD) • for nominal voltage AV 24 V, 50 ... 60 Hz Use The BAU universal digital indicator is suitable for frontal mounting in control panels, control panel doors or covers.
PAGE 2
Mechanical design Multi-part synthetic housing, comprising: − LCD digital display, 3½ digits (max. display 1999) − Electronic PCB with connection terminals and DIP switches − Front plate (frame) Mounting and installation notes Mounting instructions are enclosed with each device. The BAU universal digital indicator is suitable for frontal mounting in control panels, control panel doors or covers.
PAGE 3
Setting table DIP-switches 1 2 3 4 5 6 7 8 1 0 OPEN Type F..-T1 F..-T1 F..-T1 F..-H2 F..-Q1 CO2 V2 P1 P2 P3 FDPA FDPA FDPA FDPA FPA FPA FPA FPA FPA FPA T30 T35 T120 H90 V1 S100 P1 P2 P3 FDPE FDPE FDPE FDPE FPE FPE FPE FPE FPE FPE 0 ... 15 V A-U1 E-U1 T105 T40 T38 T20 x –50_50 x 0_100 x –100_100 x 0_500 x –50_150 x 0_200 x 100_0 y 0_100 m 0_100 xx 0_100 FT-P40 FT-PM9 FT-P4 FKA-P1 FKA-P1 FKA-P3 x 0_50 x –35_35 Sensor Interface T1 T1 T1 0 ... 10 V 0 ... 10 V 0 ... 10 V 0 ... 10 V 0 ... 10 V 0 ... 10 V 0 ...
PAGE 4
Connection terminals 940245e n 32 31 30 29 28 27 NS AC 24 V LS SNGD Input DC 0 ...10 V Supply for T1 sensor (if no controller connected) Vref. ext. (for 6 V bridge voltage for KLIMO signals only Connection diagrams (examples) 40246Aen Sensor and controller NS LS SGND AC 24 V supply To controller T1 Input 0 ... 10 V T1 sensor without controller 32 31 30 29 28 27 A 10 kohm int. D Vref.ext. 40399Aen NS LS AC 24 V supply SGND 32 31 30 T1 Input 0 ...