User's Manual
Table Of Contents
- Contents
- List of Tables
- List of Figures
- 1 Introduction and Important Notes
- 2 Overview
- 3 Planning a HiPath Cordless IP System
- 3.1 Planning According to Call Traffic Load
- 3.2 General
- 3.3 Propagation Conditions for Radio Traffic
- 3.4 Determining the Installation Site
- 3.5 Installing Base Stations
- 4 Putting Into Service
- 5 Installation and Administration
- 5.1 Terminology
- 5.2 Network Concept
- 5.3 Synchronisation over air concept
- 5.4 WBM related issues
- 5.5 Phone related issues
- 5.6 Partition concept of BSIP1
- 5.7 Factory reset of BSIP1
- 5.8 Release notes
- 5.9 Quick Start
- 5.10 Quick start overview
- 5.11 Prepare and connect hardware
- 5.12 Configure BSIP1 for IWU mode
- 5.13 Configuration of VoIP (Infrastructure) network
- 5.14 Configuration of DECT network
- 5.15 Configuration of users at the PBX
- 5.16 Configuration of users at the BSIP IWU
- 5.17 Start system services and register handsets
- 5.18 Configure further BSIP Only to the system
- 5.19 "Quick Start" Completion
- 5.20 Further steps
- 5.21 Configuration reference
- 5.22 WBM overview
- 5.23 Administration
- 5.24 "Network/Gateways" Configuration
- 5.25 "Group" Configuration
- 5.26 Users Configuration
- 5.27 Dect Configuration
- 5.27.1 Configuration Page "Dect - Device"
- 5.27.2 Configuration Page "Dect - Sync"
- 5.27.3 Configuration Page "Dect - ARI"
- 5.27.4 Configuration Page "Dect - About"
- 5.27.5 Configuration Page "Dect - Radio" (Advanced mode)
- 5.27.6 Configuration Page "Dect - Call" (Advanced mode)
- 5.27.7 Configuration Page "Dect - Debug" (Advanced mode)
- 5.27.8 General DECT configuration
- 5.28 Debugging Configuration
- 5.29 "Status" Configuration
- 5.30 "System" Configuration
- 5.31 Configuration Hints for PBXs
- 5.32 HiPath OpenOffice EE
- 5.33 HiPath OpenOffice ME
- 5.34 Troubleshooting / FAQ
- 5.35 Configuration hints for Web Browser
- 6 Technical Data
- 7 Diagnosis and Maintenance
- 8 Open Source Software used in the Product
- Index
c07.fm
Diagnosis and Maintenance
Testing the Radio Area
A31003-C1010-S100-2-7620, 08/2010
HiPath Cordless IP, Service Manual 167
The measurement values are displayed when the mobile telephone is switched
on. Measurements are performed at the set intervals (see Section 7.2.1).
Activate the measuring mode:
Using the navigation key,
scroll down to "Measuring
time".
Confirm with OK.
Measuring mode is switched
on; this is indicated by the
tick next to "Measuring
mode".
Select the measuring time:
Using the navigation key,
scroll down to "Measuring
time".
Confirm with OK.
Set the value range:
Press the navigation key:
to increase the value range
Press the navigation key:
to reduce the value range
Value range: 06 to 16
Recommended value range:
16
(measuring cycle: 1 s to 2.5
s)
Press the Save key
to confirm the value range
set
Switch off the mobile telephone:
Press the on-hook key until
the confirmation beep is
heard (ascending tone
sequence).
Nothing is displayed
OK
Service
Measuring mode
DSP parameters
Measuring time
Service 6
OK
OK
Service
Measuring time
Measuring mode
Service 7
OK
LLLLLLLLLLLLL
Service
Measuring time
Measuring time
Save
<16>
Save