MANUAL ENGLISH Infinity iW-715 Ordercode: 41520 Highlite International B.V.
Infinity iW-715 Table of contents Warning ...............................................................................................................................................................................2 Safety Instructions .........................................................................................................................................................2 Operating Determinations ............................................................................................
Infinity iW-715 Warning Unpacking Instructions Immediately upon receiving this product, carefully unpack the carton and check the contents to ensure that all parts are present, and have been received in good condition. Notify the dealer immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows signs of mishandling. Save the carton and all packing materials.
Infinity iW-715 IMPORTANT: The manufacturer will not accept liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to the device. Never let the power-cord come into contact with other cables! Handle the power-cord and all connections with the mains with particular caution! Never remove warning or informative labels from the unit. Never use anything to cover the ground contact.
Infinity iW-715 Operating Determinations ● ● ● ● ● ● This device is not designed for permanent operation. Consistent operation breaks will ensure that the device will serve you for a long time without defects. The minimum distance between light-output and the illuminated surface must be more than 1 meter. The maximum ambient temperature ta = 45°C must never be exceeded. The relative humidity must not exceed 50 % with an ambient temperature of 40° C.
Infinity iW-715 Mounting a clamp to the underside of the Infinity moving head Improper installation can cause serious damage to people and property ! Ordercode: 41520 5
Infinity iW-715 Connection with the mains Connect the device to the mains with the power-plug. Always pay attention, that the right color cable is connected to the right place. International L N EU Cable BROWN BLUE YELLOW/GREEN UK Cable RED BLACK GREEN US Cable YELLOW/COPPER SILVER GREEN Pin FASE NULL EARTH Make sure that the device is always connected properly to the earth! Return Procedure Returned merchandise must be sent prepaid and in the original packing, call tags will not be issued.
Infinity iW-715 Description of the device Features The Showtec Infinity iW-715 LED Wash is a moving-head with high output and great effects. ● Beam & Wash effect ● High torque motors ● Ultra-fast movements ● 1 Clamp rigging ● Dimmer curves: Linear, Square, I-Square, S curve ● Color balance: Separate RGBW adjustment ● On-Board: Battery powered full color display including gravity sensor ● LED source the shutter is electronic not mechanical.
Infinity iW-715 Overview Beam angle 7°/25°/50° Manual adjustment Fig. 01 01) Lens with variable beam angle 02) Menu Buttons + LCD Display Backside 03) 04) 05) 06) 07) 08) Fig. 02 NOTE: Knowledge of DMX is required to fully utilize this unit.
Infinity iW-715 Installation Remove all packing materials from the Infinity iW-715 LED Wash. Check that all foam and plastic padding is removed. Connect all cables. Do not supply power before the whole system is set up and connected properly. Always disconnect from electric mains power supply before cleaning or servicing. Damages caused by non-observance are not subject to warranty. Set Up and Operation Follow the directions below, as they pertain to your preferred operation mode.
Infinity iW-715 Multiple Infinity’s (DMX Control) 01) Fasten the effect light onto firm trussing. Leave at least 1 meter on all sides for air circulation. 02) Always use a safety cable (ordercode 70140 / 70141). 03) Plug the end of the electric mains power cord into a proper electric power supply socket. 04) Use a 3-p XLR cable to connect the Infinity’s and other devices.
Infinity iW-715 Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX-512 controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. Important: Fixtures on a serial data link must be daisy chained in one single line.
Infinity iW-715 Control Panel A) B) C) D) E) F) G) H) I) J) K) Home button Edit Menu button Settings Mode Button Address Setting Button Infinity Logo Button Up Button Down Button OK/ENTER Left Button Right Button LCD Display Fig. 05 Control Mode The fixtures are individually addressed on a data-link and connected to the controller. The fixtures respond to the DMX signal from the controller. (When you select the DMX address and save it, the controller will display the saved DMX address the next time.
Infinity iW-715 Menu Overview Ordercode: 41520 13
Infinity iW-715 Main Menu Options DMX address Edit Mode Settings Menu Built-in Programs Test Mode Info Home Up Edit Menu Down Setting Mode OK Address Setting Left Infinity Logo Right 1. DMX Addressing With this menu you can set the DMX address. 01) Press the button and select . 02) Press the button, to confirm. You can choose 512 different DMX addresses.
Infinity iW-715 2. Edit Mode With this menu you can set your desired mode. 01) Press the button and select . 02) Press the button, to confirm. You can choose 3 different modes. Use the Up / Down buttons to select the required mode: 03) Once you have selected the desired mode, press the No to YES. 04) Once you have selected the desired setting, press the buttons to change the value from button to store your settings.
Infinity iW-715 03) Once you have selected the desired mode, press the buttons to change the value from No to YES. 04) A couple of menus have more options, then your regular, yes or no function: Pan Angle: 540°, 360°, 180° Tilt Angle: 270°, 180°, 90° P/T Speed Fast, Slow Fans Auto, Full Dimmer Curve Linear, Square, I Squa, Scurve Dimmer Speed Smooth, Fast Sensitivity 001-100 05) If you press the OK button at the Color Balance, a new Menu will open.
Infinity iW-715 5. Test Menu With this menu you can set your desired mode. 01) Press the button and select . 02) Press the button, to confirm. You can choose 2 different modes. Use the Up / Down buttons to select the required mode: 03) Once you have selected the desired mode, press the buttons to change the value from 000 to 255. 04) If you press the OK button at the Manual Test, a new Menu will open. 05) You can set 7 different Test options.
Infinity iW-715 DMX Channels 14 Channels (Advanced) Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be turned by 540° and stopped at any position you wish. Channel 2 – Vertical movement (Tilt) Push the slider, up in order to move head vertically (TILT). Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
Infinity iW-715 90-94 95-99 100-104 105-109 110-114 115-119 120-124 Color 18 Color 19 Color 20 Color 21 Color 22 Color 23 Color 24 Channel 11 – Dimmer (Shutter and Colors RGBW must be open 0-255 From black to brightest ) Channel 12 – Shutter / Strobe (Dimmer must be open ) 0-19 Close 20-24 Shutter open 25-64 Strobe effect 1, from fast to slow 65-69 Shutter open 70-84 Strobe effect 2 (fast on and slow off), from fast to slow 85-89 Shutter open 90-104 Strobe effect 3 (slow on and fast off), from fast to s
Infinity iW-715 Channel 13 – Channel Functions 0-9 No Function 10-14 Blackout during Pan/Tilt movement 15-19 Reserved 20-24 Reserved 25-29 Reserved 30-34 Reserved 35-39 Reserved 40-44 Reserved 45-49 Reserved 50-54 Reset Pan after 3 seconds 55-59 Reset Tilt after 3 seconds 60-64 Reserved 65-69 Reserved 70-74 Reset all 75-79 Reserved 80-84 Reserved 85-89 Reserved 90-94 Reserved 95-99 Reserved 100-104 Reserved 105-109 Reserved 110-114 Reserved 115-119 Pan/Tilt Speed Fast 120-124 Pan/Tilt Speed Slow 125-129 Fan
Infinity iW-715 7 Channels (Basic) Channel 1 – Horizontal movement (Pan) Push the slider up, in order to move head horizontally (PAN). Gradual head adjustment from one end of the slider to the other (0-255, 128-center). The head can be turned by 540° and stopped at any position you wish. Channel 2 – Vertical movement (Tilt) Push the slider, up in order to move head vertically (TILT). Gradual head adjustment from one end of the slider to the other (0-255, 128-center).
Infinity iW-715 175-179 180-201 202-207 208-229 230-234 235-249 250-255 No Function CW Color-flow from fast to slow Stop color at this point CCW Color-flow from fast to slow No Function Color Jump from fast to slow Sound-controlled Channel 5 – Dimmer (Shutter and Colors RGBW must be open 0-255 From black to brightest ) Channel 6 – Shutter / Strobe (Dimmer must be open ) 0-19 Close 20-24 Shutter open 25-64 Strobe effect 1, from fast to slow 65-69 Shutter open 70-84 Strobe effect 2 (fast on and slow off),
Infinity iW-715 Channel settings Fig. 06 Maintenance The Showtec Infinity iW-715 LED Wash requires almost no maintenance. However, you should keep the unit clean. Otherwise, the fixture’s light-output will be significantly reduced. Disconnect the mains power supply and then wipe the cover with a damp cloth. Wipe the front glass panel clean with glass cleaner and a soft cloth. Do not use alcohol or solvents.
Infinity iW-715 Battery Replacement (must be carried out by a qualified technician!) 01) 02) 03) 04) 05) 06) 07) Unplug the unit from the electric power source. Remove the 6 screws on the front side of the Infinity. Gently pull the front cover from the device. Disconnect the plug from the PCB. Remove the 2 screws holding the battery pack in place. Replace the old battery pack with a new one. Replace the maintenance cap and fasten all screws. Fig.
Infinity iW-715 Troubleshooting No Light This troubleshooting guide is meant to help solve simple problems. If a problem occurs, carry out the steps below in sequence until a solution is found. Once the unit operates properly, do not carry out following steps. If the light effect does not operate properly, refer servicing to a technician. Response: Suspect four potential problem areas as: factory reset, the power supply, the LED, the fuse.
Infinity iW-715 Problem Probable cause(s) Remedy One or more fixtures are completely dead. No power to the fixture. ● Primary fuse blown. ● Fixtures reset correctly, but all respond erratically or not at all to the controller. The controller is not connected. 3-pin XLR Out of the controller does not match XLR Out of the first fixture on the link (i.e. signal is reversed). ● ● Connect controller. Install a phase reversing cable between the controller and the first fixture on the link.
Infinity iW-715 Product Specification Model: Input Voltage: Continuous Power: Fuse: Dimensions: Weight: Showtec Infinity iW-715 LED Wash 100-240 VAC 173W max.
Infinity iW-715 Notes Ordercode: 41520 28
Infinity iW-715 Ordercode: 41520 29
Infinity iW-715 Ordercode: 41520 30
©2014 Showtec
