Instructions / Assembly

ManualsBrandsSHORE DOCKER ManualsBoat Docks & HardwareBase Model DIY Ramp Kit

ASSEMBLY AND OPERATING INSTRUCTIONS FOR BASE MODEL / EXTENSION

WARNING: The watercraft ramp you have purchased has certain hazards associated with it’s use. Never

and

behind a watercraft while it is on the

ramp.

Never allow anyone in or on the watercraft while it is on the

ramp.

Never allow anyone to operate the ramp unless they are familiar with all of the instructions

warnings contained

her

Never try to stop a free wheeling winch handle. (Always keep a firm grip on the handle while

ratchet pawl is not fully

engaged.)

Never allow watercraft to roll free down the ramp. Injury may occur or damage to watercraft or

ramp

may

ur.

Before beginning, read the entire Assembly and Operating instructions to determine the suitability of this kit

for

your

appl

icati

on.

Congratulations on the purchase of your ShoreDocker

watercraft ramp. The following instructions provide guidelines

for

the construction of your model. Remember that with a little planning you may customize this kit to work perfectly for

you

situation. The Base / Extension model is designed for small boats and personal watercraft (PWCs, Jet Skis etc). *Not to

exceed 800 pounds (watercraft,motor,fuel,gear) as sold in kit. Additional roller sets can be purchased and added to increase

ramp capacity. Estimate one roller set per 100 pound increase in boat weight up to 1200 Lbs.

PARTS LIST FOR Base Model / Extension

16 Wheel Brackets 16 Galv 2.5” x 3/8” Hex Bolts

8 Non Marking 3.5” Polyurethane Wheels 8 SS 2.5” x 3/8” Hex Bolt

8 Bushing 8 SS 3/8” Lock nuts

4 Side Braces 8 Galv 2.5” x 3/8” Carriage Bolts

1 Drill Template 24 Galv 3/8” nuts

1 Assembly Instruction 24 Galv 3/8” lock washers

12 Coated Deck Screws

** If building a ramp for a PWC, see the important note about width on page 2 before beginning

cons

ruc

on.

**Suggested Lumber

2 ea. Pressure Treated 2” x 6” x 12’

4 ea. Pressure Treated 2” x 6” x 4’

**Optional additional ShoreDocker Accessories

Winch Kit (Includes R & L Winch post supports, 1100# winch, Hardware)

RS1200 (additional roller sets)

WSB (additional side braces)

Summary of content (4 pages)

PAGE 1
ASSEMBLY AND OPERATING INSTRUCTIONS FOR BASE MODEL / EXTENSION WARNING: The watercraft ramp you have purchased has certain hazards associated with it’s use. Never stand behind a watercraft while it is on the ramp. Never allow anyone in or on the watercraft while it is on the ramp. Never allow anyone to operate the ramp unless they are familiar with all of the instructions and warnings contained herein. Never try to stop a free wheeling winch handle.
PAGE 2
First you will build the basic framework. STEP 1: DETERMINE THE LENGTH AND LUMBER DIMENSIONS NEEDED. You will likely want to store your watercraft all the way out of the water and away from any wave action. Also remember that a few feet of the ramp will extend into the water so that the rollers first engage the hull below the bow. For the side rails or main supporting beams it is recommended that you use 2 x 6s with 2 x 4s for the cross members. Use pressure treated lumber for longer life.
PAGE 3
STEP 4: Install roller assemblies as shown. Assemble as shown in the figures below. Consider the following criteria when selecting the location of the roller assemblies: a. Assemblies should obviously be in pairs, i.e. identical location on both the right and left rail. b. The first pair (from the water end of the ramp) should be close to the water end of the rail. c. Roller assembly pairs should be spaced more closely together where watercraft weight is greater.
PAGE 4
SETTING UP AND OPERATION OF SHORE DOCKER BOAT RAMP Because Shore Docker is a kit, you are responsible for the safe construction, setup and operation of your ramp. Shore Docker only supplies parts and general guidelines. There are many types of boats and shorelines. You must make the decision of the suitability of this kit for your situation. Locate the ramp with the water end deep enough to easily engage your hull. Hook the end of the winch cable to the eye on your bow.