G10 Laser Engraver Quick Start User Manual This manual was written for the G10 Laser Engraver. There are some differences between versions. This is normal. Any new documentation about your version will prevail. For more details, please read the usage guide on the TF Card.
Contents Enquiptment Introduction……………………1 Unboxing contents…………………..…………2 Equipment Installation………………..…...3-5 Equipment Wiring…….…………………...…..6 Equipment Adjustment…………………….…7 Focal length Adjustment………………….....8 Screen Information…………………………...9 Network connection and engraving…...10 APP Usage………………………………………11 Online engraving …………………..………..12 Safety Information……………..…… 13-14 Troubleshooting.……………………….....
NOTICE 1. Do not try to use the machine in any way not described in the instructions to avoid accidental personal injury and property damage; 2. Please do not place the machine near flammable and explosive materials or high heat sources, please place the machine in a ventilated, cool and less dusty environment; 3. Please do not place the machine in a vibrating or other unstable environment, machine shaking will affect the quality of engraving/cutting; 4.
1.
2.
3.设备安装 3. Equipment Installation Install the left and right beams on the back beam. M5*10 2PCS M5*20 2PCS As shown in the picture, install the X beam components into the left and right beams.
3. 3.设备安装 Equipment Installation Mount the front beam assembly on the left and right beam as shown As shown, mount the laser on the back plate M5*20 2PCS M5*10 4PCS Wrap the timing belt on the left and right side of the Y-axis around the timing pulley M3*8 hand screws 2PCS A closer view 43 Pull the timing belt tight and secure it with screws and flat spacers.
3.设备安装 3. Equipment Installation Install the foot assemblies to the machine from the bottom Install the Foot Assembly Caps on the foot assemblies A closer view M5*8 4PCS Cardboard snaps into foot slot Fit the hand screw nuts into the left and right profiles to fix the foot assembly, which can be adjusted up and down in height.
4.
5. 5.屏幕信息 Equipment adjustment Loosen the hand screw nut, you can adjust the laser head up and down, and tighten it when it is adjusted to the right position. 7 Loosen the hand screw nut, you can adjust the four feet up and down, and tighten it when it is adjusted to the right position.
A2 6. Focal Length Adjustment Loosen the hand screws shown in the figure and pull down the acrylic cover to the lowest point after tightening the screw. Schematic After loosening the hand screws shown in the figure and allowing the bottom surface of the acrylic cover to come in contact with the item being engraved, tighten the screw. Loosen the hand screws shown in the figure, and lift the acrylic cover up to the highest position and then tighten the screw.
7.Screen Information Main Menu Control Setting Primary Directory 10mm Set single movement distance, switchable to 0.1mm, 1mm, 10mm Move Control the direction of movement to operate each axis of X, Y, Z movement Zero Set (Home) XYZ to Zero Laser Emits laser light, fixing focus, etc.
6.网络连接及雕刻 8.
9. APP Usage Software Download and Installation: Apple phones can search for MKSLaser in the App Store ,then download and install. Android phones can install the app by copying the MKSLaser installation software from the memory card to the phone. WIFI Connection: The phone needs to be in the same network environment as the engraver. On the main screen of the app, click on the connection icon in the upper left corner You can choose the material, create, control, and engrave on the home page.
10. Online Engraving For engraving over USB, you connect the computer and the engraving machine using the data cable. While engraving, the computer cannot be powered off, and the computer cannot enter the screen saver or hibernate, to prevent data transfer failure. When you use the USB cable to connect the engraver to the computer, and if the driver cannot be loaded correctly, proceed as follows: Open the distributed SD card and select the path (computer \F:\2. software and driver \online driver\USB drive
11. Safety Information Improper use of the laser engraver can cause eye and skin injury, fire or other serious consequences. Please read this section of the laser engraver instructions before you begin to ensure that it is used correctly. Electrical Safety In order to reduce the risk of electric shock or fire,except as advised by qualified Lotmaxx representatives. Do not attempt to repair or modify the machine. Do not attempt to disassemble the machine's wiring.
Watch out during laser operation Please do not operate the laser engraver and leave it unattended, you need to stay in sight at all times. It is normal for the laser beam to produce a burning spot on the material. The spot should move continuously with the laser head and not remain burning in the same position for a long period of time, if this results in a flame, please do the following: 1. Make sure the machine is turned off. Push the emergency stop switch and disconnect the power cord. 2.
12. Troubleshooting Problem Description Troubleshoot Location Solutions Engraving a single straight line, or the file being engraved produces doubled lines 1. Check whether the synchronous belt for X/Yaxis are moving. 2. Check whether the speed of the engraving file is too fast. 1. After loosening the fixing screws of the too loose timing belt, re-stretch the timing belt and set it with the fixing screws. 2. Reduce the engraving speed when slicing files. 3. Check wire connections if belt is tight.
Official Website QR Code Shenzhen Senma Utrend Co.Ltd.
FCC Warning This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any inte rference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.