Installation Guide

ManualsBrandsSharp ManualsAppliances30 in. W 1.2 cu. ft. Built-In Microwave Drawer with Easy Touch Control in Real Stainless

SPECIAL WARNING

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.

IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE.

READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CLEARANCES ANd dImENSIoNS

For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated

clearances and dimensions on pages 2 - 5. See Figure 1 (for 24") or Figures 4 and 5 (for 30").

Microwave Drawer : SMD2470AS, SMD3070AS

InstallatIon Manual

UNPACkING yoUR mICRoWAvE dRAWER

 Remove all packing

materials from inside

the Microwave Drawer.

DO NOT REMOVE

THE WAVEGUIDE

COVER, which is

located on the top

of the Microwave

Drawer.

 Remove the feature

sticker, if there is one.

Check the drawer for

any damage, such as

misaligned or bent

drawer, damaged drawer seals and sealing surfaces, broken

or loose Microwave Drawer guides and dents inside the cavity

or on the front side of the drawer. If there is any damage, do

not operate the Microwave Drawer and contact your dealer or

a SHARP AUTHORIZED SERVICER.

ImPoRtANt NotES to thE INStALLER

 Read all of the Installation Manual before installing the

Microwave Drawer.

  Remove all packing material before connecting the electrical

supply.

  Observe all governing codes and ordinances.

  Be sure to leave these instructions with the consumer.

ImPoRtANt NotES to thE CoNSUmER

Keep this manual with your Operation Manual for future

reference.

 As when using any microwave oven generating heat, there

are certain safety precautions you should follow. These are

listed in the Operation Manual. Read all and follow carefully.

 Be sure your Microwave Drawer is installed and grounded

properly by a qualied installer or service technician.

ImPoRtANt SAfEty INStRUCtIoNS

If the information in this manual is not followed

exactly, a re or electrical shock may result that could cause

property damage, personal injury or death.

To reduce the risk of tipping, the Microwave

Drawer must be secured by a properly installed Anti-Tip

block.

 This Microwave Drawer must be electrically grounded in

accordance with local codes.

 Make sure the wall coverings and the cabinets around the

Microwave Drawer can withstand the heat generated by the

Microwave Drawer.

Never leave children alone or unattended in

the area where a Microwave Drawer is in use. Never leave the

drawer open when the microwave is unattended.

Stepping, leaning or sitting on the drawer may

result in serious injuries and can also cause damage to the

Microwave Drawer.

 Do not use the Microwave Drawer as a storage space.

This creates a potentially hazardous situation.

 Check that the time-of-day is in the display. If not, touch

STOP/CLEAR to prevent unintended use.

Mounting

flange

Waveguide

cover

Sealing

surface

Oven

cavity

Sealing

surface

Summary of content (8 pages)

PAGE 1
Microwave Drawer : SMD2470AS, SMD3070AS Installation Manual SPECIAL WARNING INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER. IMPORTANT: SAVE this installation manual FOR LOCAL ELECTRICAL INSPECTOR’S USE. READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Clearances and Dimensions For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated clearances and dimensions on pages 2 - 5.
PAGE 2
Clearances and Dimensions • Your oven can be built into a cabinet or wall by itself or under a gas or electric wall oven. • Dimensions that are shown in Figure 1 (for 24") or Figures 4 and 5 (for 30") must be used. Given dimensions provide minimum clearance. Locate electrical outlet in the shaded area in the upper left-hand corner of the cutout. See Figure 9. • Be sure that the clearance of the floor between the wall oven and the microwave drawer is a minimum of 2-inches.
PAGE 3
This drawing represents a typical standard cabinet. If installed in custom cabinets with extended counter tops, take into account visibility and access to controls. See Figure 3. A Move oven location downward for extended countertops B E Extended countertops Figure 3 C D G F 3 A. 25" B. 1/2" minimum C. 15-7/8" D. 36" E. Control panel shown in open position F. 24" G.
PAGE 4
30" Microwave Drawer Measurements Figures 4, 5 and 6 contain many Microwave Drawer measurements for reference when planning the drawer’s location. * Can also be installed using an electrical outlet in an adjacent cabinet within the area where the provided electrical cord can reach. Power cord access hole in cabinet should be a minimum 1 1/2" diameter hole and deburred of all sharp edges. This Microwave Drawer can be installed below any electric or gas wall oven.
PAGE 5
C B A M Cutout Dimension 28 7/16" x 15 9/16" E D A. 6" B. Suggested electrical outlet location* C. Anti-Tip block D. 5" E. 3-1/2" F. 4" G. 28-7/16" opening H. 14-13/16" to bottom of Anti-Tip block I. Allow 23/32" overlap J. 23-1/2" minimum depth K. Allow 3/16" overlap L. 36" countertop height M. Allow 7/16" overlap N. Floor must support 100 lb O. 30" cabinet minimum P. 15-9/16" opening Q. Allow 1/8" overlap F G K I H P J I L N Q O Figure 5 J B C A F G I D H Figure 6 E 5 A.
PAGE 6
This drawing represents a typical standard cabinet. If installed in custom cabinets with extended counter tops, take into account visibility and access to controls. See Figure 7. A Move oven location downward for extended countertops B E Extended countertops Figure 7 C D G A. 25" B. 1/2" minimum C. 15-7/8" D. 36" E. Control panel shown in open position F. 24" G.
PAGE 7
Anti-Tip BLOCK NORMAL INSTALLATION STEPS Anti-Tip BLOCK Installation Instructions To reduce the risk of tipping of the drawer, the Anti-Tip block must be properly installed located 14 13/16 -inches above the floor on which the Microwave Drawer will sit. The 6-inch Anti-Tip block must be provided by the installer. See Figures 1, 4 and 5. The Anti-Tip block prevents serious injury that might result from spilled hot liquids.
PAGE 8
Drawer Installation 1. Place the drawer adjacent to the wall or cabinet opening. Plug the power supply cord into the electrical outlet. 2. Carefully guide the drawer into the prepared opening. Avoid pinching the cord between the oven and the wall. Parts supplied 3. Slide the drawer all the way until the mounting flange is flush with the face of the cabinet. See Figure 10A. 4 Screws 4. Open the drawer. Using the 4 holes on the drawer as a template, pre drill the cabinet using a 1/16" bit.