User's Manual

ManualsBrandsSharp ManualsFlat Panel TVSharp Sharp Flat Panel Television LC60LE650U

Adjusting the PC Image

You can adjust the position of the image input from

a PC the settings with "System Options" > "Terminal

Setting" > "PC input".

Auto Sync. (for Analog PC Input Mode Only)

For automatically adjusting the PC image.

Yes: Auto Sync. starts and "Now adjusting the

image." displays.

No: This function does not work.

NOTE

• When "Auto Sync." is successful, "Completed"

displays. If not, "Auto Sync." failed.

• "Auto Sync." may fail even if "Completed" displays.

• "Auto Sync." may fail if the computer image has low

resolution, has unclear (black) edges, or is moved while

executing "Auto Sync.".

• Be sure to connect the PC to the TV and switch it on

before starting "Auto Sync.".

Fine Sync.

Ordinarily you can easily adjust the picture as

necessary to change image position using "Auto

Sync.". In some cases, however, manual adjustment

is needed to optimize the image.

H-Pos.: Centers the image by moving it to the left or

right.

V-Pos.: Centers the image by moving it up or down.

Clock: Adjust when the image ﬂ ickers with vertical

stripes.

Phase: Adjust when characters have low contrast or

when the image ﬂ ickers.

NOTE

• For resetting all "Fine Sync." adjustment items to the

factory preset values, press

to select "Reset",

and then press ENTER.

• It is not necessary to adjust the "Clock" or "Phase"

when a digital signal is being input, so it cannot be

selected.

• The default cursor position may not be in the center,

because the screen position variable ranges may be

asymmetrical.

• The screen position variable ranges depend on the

View Mode or the signal type. The ranges can be seen

on the position-setting screen.

Setting Audio Input

Audio Select

This function sets the terminal to output the computer

audio.

The adjustment items vary depending on the input

source. Select the input source corresponding to the

terminal connected to the PC and then adjust the

desired item.

To perform the operation, refer to "System Options"

> "Terminal Setting" > "Audio Select".

■

PC IN

Video: Select this when the TV and PC are

connected using an analog RGB cable and the

audio is not input.

Video+Audio: Select this when the TV and PC are

connected using an analog RGB cable and the

audio is input via a Ø 3.5 mm stereo minijack.

■

HDMI 2

HDMI(Digital): Select this when the TV and PC are

connected using an HDMI-certiﬁ ed cable and

audio is input via the same cable.

HDMI+Analog: Select this when the TV and PC are

connected using a DVI-HDMI conversion cable

and the audio is input via a Ø 3.5 mm stereo

minijack.

NOTE

• When "Audio Select" is set to "HDMI(Digital)", sound

will not be produced if you use only an HDMI-certiﬁ ed

cable to connect HDMI-compatible equipment. To

produce sound, you should make an analog audio

connection.

• If you want to connect HDMI-compatible equipment

using only an HDMI-certiﬁ ed cable, set "Audio Select"

to "HDMI(Digital)".

Control of the TV

• The TV can be controlled from a PC, control panels

and other devices using the RS-232C or IP.

• Use a cross-type RS-232C cable, ETHERNET

cable (commercially available) or wireless LAN for

the connections.

NOTE

• This operation system should be used by a person

who is accustomed to using computers.

AQUOS Remote Control

Set this function when operating the TV from equipment

connected by LAN or wireless LAN. To perform the

operation, refer to "Initial Setup" > "Internet Setup".

■

AQUOS Remote Control

When "AQUOS Remote Control" is selected,

"Change" will be highlighted. Press ENTER.

■

Detailed Settings

Make the detailed settings (Login ID, password, etc.).

Follow the on-screen instructions to conﬁ gure the

settings.

TV Name Setting

Set the name of the TV displayed on other network

devices.

• Use the software keyboard to set the name. See page

47 for details on the software keyboard.

Communication Conditions for IP

Connect to the TV with the following settings made

for IP on the PC.

IP protocol: TCP/IP

Host IP address:

Set the IP address on the TV menu

Service: None (Do not select Telnet or

SSH)

TCP port#: Set a port number on the TV

menu (Control port)

When you set your ID and password on the TV menu, you

need to enter them as soon as you connect to the TV.

NOTE

• When you use this function, make settings for "AQUOS

Remote Control".

• The connection will be cut off when there has been no

communication for 3 minutes.

Communication Conditions for RS-232C

Set the RS-232C communication settings on the PC

to match the TV's communication conditions.

The TV's communication settings are as follows:

Baud rate: 9,600 bps

Data length: 8 bits

Parity bit: None

Stop bit: 1 bit

Flow control: None

■

Communication procedure

Send the control commands from the PC via the RS-

232C or IP.

The TV operates according to the received command

and sends a response message to the PC.

Do not send multiple commands at the same time.

Wait until the PC receives the OK response before

sending the next command.

■

Command format

Eight ASCII codes

Command 4-digits Parameter 4-digits Return code

C1 C2 C3 C4 P1 P2 P3 P4

Command 4-digits: Command. The text of four characters.

Parameter 4-digits: Parameter 0–9, x, blank, ?

■

Parameter

Input the parameter values, aligning left, and ﬁ ll with

blank(s) for the remainder. (Be sure that 4 values are

input for the parameter.)

When the input parameter is not within an adjustable

range, "ERR" returns. (Refer to "Response code

format".)

Any numerical value can replace the "x" on the table.

a 30

0009

????

When "?" is input for some

commands, the present

setting

value

responds.

■

Response code format

Normal response

Return code (0DH)

Problem response

(communication error or incorrect command)

ERR

Using a PC

LC-80LE857U_757U_657U_E.indd 44 2013/02/21 13:36:04