PN-ZCMS1 Operation Manual

- EN 4 - - EN 5 -
19. Usage of this product must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,
severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and
missile launch control in a weapon system.
20. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in
low-temperature burns.
21. Do not modify this product.
WARNING:
This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may
be required to take adequate measures.
WARNING:
• Keep the battery away from children. Chemical burn hazard.
• If the battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
• If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical
attention.
• If the battery compartment does not close securely, stop using the product and keep it away from children.
Australian Poisons Information Centre
Call this number if you think someone has swallowed a button/coin battery.
You can call 24 hours a day, 7 days a week from anywhere in Australia.
Phone: 131 126
Warnings for safe disposal of Batteries
• Place non-conductive adhesive tape around both sides of the battery and dispose/recycle
immediately and safely out of reach of children.
• Safely dispose/recycle used button/coin batteries following local council/government guidelines.
• Information about these guidelines can be found at the following link.
https://www.sharp.net.au/battery
SAFETY INSTRUCTION
- Do not use this product where there is a lot of dust, where
humidity is high, or where this product may come into
contact with oil or steam. Do not use in an environment
where there are corrosive gases (sulfur dioxide, hydrogen
sulfide, nitrogen dioxide, chlorine, ammonia, ozone, etc.). As
this could lead to fire.
- Ensure that this product does not come into contact with
water or other fluids. Ensure that no objects such as paper
clips or pins enter this product as this could lead to fire or
electric shock.
- Do not place this product on top of unstable objects or in
unsafe places. Do not allow this product to receive strong
shocks or to strongly vibrate. Causing this product to fall or
topple over may damage it.
- Do not place this product upside down. Do not place
anything on this product. As this could lead to overheating,
fire, or malfunction.
- Do not use this product near heating equipment or in places
where there is likelihood of high temperature, as this may
lead to generation of excessive heat and outbreak of fire.
- Do not use this product in places where it may be exposed
to direct sunlight. Risk of cabinet deformation and failure if
this product is used in direct sunlight.
- The power outlet shall be installed near the equipment and
shall be easily accessible.
- For a complete electrical disconnection, pull out the main
plug.
- Provide enough space around this product to prevent heat
from accumulating inside.
- Use only the specified bracket and camera screw to secure
this product. Do not use anything other than the items
specified.
-
Mounting this product on the wall requires special expertise
and the work must be performed by an authorized SHARP
dealer. You should never attempt to perform any of this work
yourself. Our company will bear no responsibility for accidents
or injuries caused by improper mounting or mishandling.
- Please understand that SHARP CORPORATION bears no
responsibility for errors made during use by the customer or
a third party, nor for any other malfunctions or damage to this
product arising during use, except where indemnity liability is
recognized under law.
- This product and its accessories may be upgraded without
advance notice.
The Power Cord
- Use only the power cord supplied with this product.
- Observe the following. Incorrect handling may result in fire,
electric shock, or injury.
• Do not drop the power cord or subject it to impact.
• Never disassemble the power cord. It contains high
voltage parts that are dangerous to touch.
•
The power cord is for indoor use only. Do not use it outside.
• Do not use the supplied power cord with other devices.
- Do not damage the power cord nor place heavy objects on
it, stretch it or over bend it. Also, do not add extension cords.
Damage to the cord may result in fire or electric shock.
- Do not use the power cord with a power tap.
Adding an extension cord may lead to fire as a result of
overheating.
- Do not remove or insert the power plug with wet hands.
Doing so could result in electric shock.
- Unplug the power cord if it is not used for a long time.
- Do not attempt to repair the power cord if it is broken
or malfunctioning. Refer the servicing to the service
representative.
Supplied Components
If any component should be missing, please contact your dealer.

Remote control unit: 1

Power cord (AC adapter): 1

Coin lithium battery (for remote control unit, CR2032): 1

USB cable: 1

Camera screw*
1
: 1

Lens cap: 1

A/B wall mount bracket: 1 each

Wall mount bracket screw: 4*
2

Wall mount bracket anchor: 4*
2

Operation Manual (this manual): 1
* For environmental protection!
Do not dispose of batteries in household waste. Follow the disposal instructions for your area.
*
1
The camera screw is for fixing this product and the B wall mount bracket (supplied). Do not use it for other bracket.
*
2
1 item is a spare.
1. Camera
The upper and lower angle can be adjusted.
2. Camera LED
White lit: camera on
Off: camera off
3. Power / Mic LED
White lit: power on, mic on
Red lit: power on, mic off
Off: power off
4. Mic mute button
The mic switches between ON/OFF each time the button is
pressed.
5. Audio input/output terminal
Used to connect to external earphone/mic/speaker
conforming to the CTIA standard.
When connected, the internal speaker will be disabled. Both
the internal and external mic will be enabled.
6. USB2.0 port (Type-C shape)
Use the supplied USB cable to connect to the USB port of
the monitor or computer.
Can be used as an external camera, mic, or speaker of the
monitor (APPLICATION mode, “Web Browser” only) or computer.
For details on the connection destination when a connection
is established to the USB port of the monitor, refer to the
manual of the monitor.
7. DC input terminal
Connected to a power outlet via the supplied power cord.
1
2 3
45 67
Front view
Rear view
Part Names
Caution
• Power is supplied at all times as long as the power cord is connected.
If this product is not going to be used for a long time, remove the power cord from the power outlet.
• Before using this product, confirm the plug is secured to the AC adapter.
• Do not press the button (*) on the AC adapter during use. It is dangerous because the plug will remove.
TIPS
• This product has a noise reduction function that is constantly running, so noise reduction function in the settings of application
should be switched off.
• The resolution of the camera images depends on the application. In addition, the resolution of the transmitted camera images
may be low due to network conditions.
Australia Only
*