Flat Panel Television User Manual

30
Viewing 3D Images
NOTE
The TV screen may temporarily become black when
the TV is trying to detect a 3D image signal and when
switching from 3D to 2D mode.
Receiving a 3D Image Signal That Can
Be Detected Automatically
The image signal may contain a 3D identifi cation
signal. You can enable the TV to automatically detect
the 3D image type by selecting "System Options"
> "3D Setup" > "3D Auto Change" on the TV. (See
page 31.)
1
When "3D Auto Change" is set to "Mode 1"
or "Mode 2"
The 3D image type is detected automatically and
the appropriate 3D image is displayed.
Changed to 3D mode.
Power on the 3D glasses then put them on.
If you are in bad physical conditions
or feel uncomfortable watching 3D picture
please stop watching monitor.
3D
When "3D Auto Change" is set to "Off"
The following message is displayed. Press 3D.
3D picture is detected.
Power on the 3D glasses.
(Need to wear the 3D glasses to watch 3D picture)
• Press
c
/
d
to select the "Yes", and then press
ENTER.
2
Turn on the 3D Glasses and place them on your
head.
3
You can now view 3D images.
Switching from 3D to 2D Mode
4
Press 3D during the 3D mode.
Select "Yes" and press ENTER to switch to 2D
mode.
Take off the 3D Glasses and turn off the power.
Ending 3D Image Viewing
5
Take off the 3D Glasses and turn off the power.
NOTE
If the input signal switches to 2D, 2D images are
displayed automatically.
3D mode is canceled automatically when the setting is
changed, input selection is changed, or the power is
turned off.
Receiving a 3D Image Signal That
Cannot Be Detected Automatically
1
Press 3D.
A screen appears prompting you to select
between 3D and 2D image viewing.
2
Press
c
/
d
to select "3D" or "2D", and then
press ENTER.
To view in 3D mode: Select "3D", and then go to
step 3.
To view in 2D mode: Select "2D", and then go to
step 6.
3
Press
c
/
d
to select the 3D signal type
("2D
3D", "Side by Side" or "Top and Bottom")
and then press ENTER.
2D -> 3D Side by Side Top and Bottom
If you select the same system as that of the input
signal, 3D images are displayed.
4
Turn on the 3D Glasses and place them on your
head.
5
You can now view 3D images.
Switching from 3D to 2D Mode
6
Press
c
/
d
to select the 2D signal type ( "Side
by Side" or "Top and Bottom") and then press
ENTER.
Side by Side Top and Bottom
If you select the same system as that of the input
signal, 2D images are displayed.
Take off the 3D Glasses and turn off the power.
Ending 3D Image Viewing
7
Take off the 3D Glasses and turn off the power.
Display Methods for 3D and 2D Images
Display method Example display Description
3D mode
(using the
3D Glasses)
2D
3D
Converts normal 2D images into 3D images.
Side by Side
Creates 3D images from 3D images displayed side by side.
The image is split into a left and right image, and then the
images are stretched and displayed sequentially to create
a 3D image.
Top and Bottom
Creates 3D images from 3D images displayed on the
top and bottom. The image is split into a top and bottom
image, and then the images are stretched and displayed
sequentially to create a 3D image.
2D mode
(without
using the
3D Glasses)
Side by Side
2D
Creates 2D images from 3D images displayed side by side.
Only the left image is stretched and displayed. The image
does not appear in 3D.
Top and Bottom
2D
Creates 2D images from 3D images displayed on the
top and bottom. Only the top image is stretched and
displayed. The image does not appear in 3D.
Enjoying 3D Image Viewing
LC-70UD1U_E.indd 30 2013/07/03 15:30:18