UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SERVICE MANUAL No. 00ZUX510U/SME FACSIMILE UX-510 UX-500 MODEL FO-1460 MOD ELMOD ELUX CONTENTS CHAPTER 1. GENERAL DESCRIPTION [1] Specifications . . . . . . . . . . . . . . . . . . . . . 1-1 [2] Operation panel . . . . . . . . . . . . . . . . . . . . 1-2 [3] Transmittable documents . . . . . . . . . . . . 1-3 [4] Installation . . . . . . . . . . . . . . . . . . . . . . . . 1-4 [5] Quick reference guide . . . . . . . . . . . . . . .
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri-Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U CHAPTER 1. GENERAL DESCRIPTION [1] Specifications Applicable telephone line: Public switched telephone network Effective scanning width: Compatibility: ITU-T (CCITT) G3 mode Automatic document feeder: 20 sheets max. Configuration: Half-duplex, desktop transceiver Halftone (gray scale): 64 levels Memory size*: 512 KB (approx.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [2] Operation panel SPEED DIAL key Press this key to dial a 2-digit Speed Dial number. Display This displays various messages during operation and programming. ABC 1 Number keys Use these keys to dial numbers, and enter numbers and letters during number/name storing procedures.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [3] Transmittable documents 5. Automatic Document Feeder Capacity 1. Document Sizes Number of pages that can be placed into the feeder at anytime is as follows: Normal size width 5.83"–8.5"(148 – 216 mm) length 5.04" – 11"(128 – 279 mm) Normal size: max. ADF 20 sheets (14 lbs – 20 lbs) Special size: single sheet only (manual feed) NOTES: (Max.) (Max.) Letter size (Min.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 7. Use of Document Carrier Sheet TELEPHONE JACK A document carrier sheet must be used for the following documents. A standard RJ11C telephone jack must be located near the machine. This is the telephone jack commonly used in most homes and offices. • • Those with tears. • Carbon-backed documents • Those smaller than size 5.83"(W) x 5.04"(L) (148 mm (W) x 128 mm (L)). Make print straight across paper E.G.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 3 Take the new film out of its package, and insert two of the gears 7 Insert the empty spool into the back of the compartment so that provided with the fax into the ends of the spool with film. Make sure that the two tabs on the gears fit properly into the slots in the ends of the spool. • the gear and the flange fit into the slots on the sides of the compartment. • Make sure that the gear engages with the gear below it.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 3. Assembly and connections 4. Loading printing paper 1 Plug the power cord into a 120 V, 60 Hz, grounded (3-prong) The paper tray holds the paper on which received documents and copies are printed. Up to 200 sheets of letter or legal size paper from 16 to 24 lbs. (60 to 90 g/m2) can be loaded in the tray. outlet. 1 Remove the paper cover if it is on the paper tray. Caution: Do not plug the power cord into any other kind of outlet.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 4 Replace the paper cover on the paper tray and then push the 5. Clearing paper jams paper release plate back down. • If a document doesn’t feed properly during transmission or copying, or DOCUMENT JAMMED appears in the display, first try pressing the START key. If the document doesn’t feed out, open the operation panel (grasp the front edge at the "PANEL RELEASE" mark and pull up) and pull it out gently.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 4 Replace the imaging film, making sure that the flange goes into 6 Close the print compartment cover, making sure it clicks into the rear slot on the left side of the printing compartment. Also, make sure that the right, rear gear engages with the gear below it. place.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U INSTALLATION SETTING THE DATE AND TIME To set date and time, press the following keys: FUNCTION 3 "DATE & TIME SET" will appear in the display. START Press the START key: Enter two digits for the Month (01 through 12). Enter two digits for the Date (01 through 31). TEL SET. Enter two digits for the Year (00 through 99). TEL LIN . E Enter two digits for the Hour (01 through 12). Enter two digits for the Minute (00 through 59). EXT . PHO NE TEL LIN .
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Loading paper Installing the imaging film 1. Insert the paper tray into the fax if not yet installed. 1. Press the release marked OPEN and open the print compartment cover. 2. Insert two of the gears into the ends of the spool with film. 2. Remove the paper cover if it is on the tray. (For legal paper, flip up the tray externder.) 3.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [6] Option imaging film specifications (UX-15CR/FO-15CR) 1. Structure This article is composed of polyester film coated with heat-resistant layer, matt layer and hot melt ink layer, leader film and paper core. Ink film specification is "DNP standard ink film HC". 1 2 3 4 1 2 3 4 Heat Resistant Layer Base Film Matt Layer Hot melt Ink Layer 2. Details of compositions 2-1.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U CHAPTER 2. ADJUSTMENTS (1) FU100 (ICP-S07) is installed in order to protect IC’s from an overcurrent generated in the motor drive circuit. If FU100 is open, replace it with a new one. [1] Adjustments 3. Settings (1) Dial mode selector General DIAL mode (Soft Switch No. SWB4 DATA No. 3) Since the following adjustments and settings are provided for this model, make adjustments and/or setup as necessary. (step 1) Select "OPTION SETTING". FUNCTION 4 1.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [2] Diagnostics and service soft switch 1. Operating procedure (1) Entering the diagnostic mode Press FUNC → 9 → ROM Ver. FHG0 → 8 → # → 7 , and the following display will appear. After 2 sec: DIAG MODE FHG0 Then press the START key and country name selected by country select will appear. Select the desired item with the or select with the rapid key. Enter the mode with the START key. key or the # key (Diag•specifications) FUNC 9 8 7 DIAG MODE Ver.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 3. Diagnostic items description 3. 6. Signal send mode The mode is used to send various signals to the circuit during FAX communication. Every push of START key sends a signal in the following sequence. Moreover, the signal sound is also output to the speaker when the line monitor of the soft switch is on. 3. 1. Soft switch mode Used to change the soft switch settings. The soft switch which is stored internally is set by using the keys.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 3. 12. Entry data receive This mode is used to receive the registered data which is sent from the remote machine and to register the received data in the machine. When this mode is used to receive the information, the remote machine must be set to the entry data send mode. The information to be sent is as follows. 1. Telephone number registration list 2. Sender registration list 3. Setting of optional setting 4. Soft switch setting 5. Junk FAX number 6.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 5. Soft switch description • Soft switch SW DATA NO. NO. SW l A1 Switch setting and function ITEM 1 1 Protect from echo No Yes 2 Forced 4800 BPS reception Yes No 0 3 Footer print Yes No 0 4 Length limitation of copy/send/receive No limit Copy/send: 1m Receive: 1.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW DATA NO. NO. SW l A6 Switch setting and function ITEM 1 Auto gain control (MODEM) Enable Disable 1 2 End Buzzer Yes No 1 3 Disconnect the line when DIS is received in RX mode No Yes 1 4 Equalizer freeze control (MODEM) On Off 0 5 Equalizer freeze control 7200 BPS only No Yes 6 Reserved 0 7 Reserved 0 8 Reserved 1 Recall interval No. = 1 0 0 1 0 1 1 Binary input 0 Recall times No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW DATA NO. NO. 1 Switch setting and function ITEM 1 DTMF signal transmission level (High) Binary input 0 16 8 4 2 1 0 3 1 2 3 4 5 1 4 0 0 1 1 1 2 SW l B6 No. = 1 6 Reserved 0 7 Reserved 0 8 Reserved 0 1 No. 1 2 No. 2 Reading slice (Half tone) Factory setting Light Dark Darker in dark mode 0 1 0 1 0 0 0 0 1 1 Factory setting Light Dark Darker in dark mode 3 No. 3 0 1 0 1 0 4 No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW DATA NO. NO. SW l E2 Switch setting and function ITEM 1 1 Reserved 0 2 Reserved 0 3 Reserved 0 4 Reserved 0 5 Reserved 0 6 Reserved 0 7 Reserved 0 8 Reserved 1 2 3 Protection of remote reception (5 4 Remote reception with GE telephone 5 Remote operation code figure by external TEL (0~9) 6 ) detect 50ms 80ms 100ms 120ms No. 1 0 0 1 1 0 No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW DATA NO. NO. SW l H1 Switch setting and function ITEM 1 1 Busy tone detection ON/OFF time (Lower duration) 350ms 200ms 0 2 Busy tone detection ON/OFF time (Upper duration) 650ms 900ms 0 3 Reserved 4 Busy tone continuous sound detect time 5s 10s 5 Reserved 6 Busy tone detect continuation sound detect (during ICM: for internal A.M.) 7 Reserved 8 Busy tone detect intermittent sound detect (during ICM: for internal A.M.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW DATA NO. NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW DATA NO. NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U • Soft switch function description SW-A2 No. 7 Communication error treatment in RTN sending mode (Reception) Used to determine communication error treatment when RTN is sent by occurrence of a received image error in G3 reception. When it is set to "1", communication error is judged as no error. SW-A1 No. 1 Protect from echo Used to protect from echo in reception. SW-A1 No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW-A5 No. 5, No. 6 Digital cable equalizer setting (Reception for Caller ID) Line equalization when reception for CALLER ID is to be set according to the line characteristics. SW-B4 No. 1 Auto dial mode Delay timer of before line connect Delay time between the dial key input and line connection under the auto dial mode. RAPID01 CML RELAY ON Setting should be made according to distance between the telephone and the telephone company central switching station.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW-D1 No. 1 ~ No. 4 Number of rings for auto receive When the machine is set in the auto receive mode, the number of rings before answering can be selected. It may be set from one to four rings using a binary number. Since the facsimile telephone could be used as an ordinary telephone if the handset is taken off the hook, it should be programmed to the user’s choice. If the soft switch was set to 1, direct connection is made to the facsimile.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW-G3 No. 1 ~ No. 3 Reserved Set to "0". SW-I3 No. 1 ~ No. 8 Reserved Set to "0". SW-G3 No. 4 TAD (A.M.) connect When connecting the answering machine to the extension telephone jack. SW-I4 No. 1 ~ No. 8 Reserved Set to "0". SW-I5 No. 1 ~ No. 8 Reserved Set to "0". SW-G3 No. 5, No. 6 Section time of quiet detection The switch which sets the time from the start of detection function to the end of the function. SW-I6 No. 1 ~ No. 8 Reserved Set to "0". SW-G3 No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U SW-J3 No. 5 ~ No. 8 Reserved Set to "0". SW-K1 No. 1 Entering DIAG mode by pressing SPEED key A bit which is used in the production process only. When the SPEED key is pressed, the switch is changed from the stand-by state to the DIAG mode. SW-K1 No. 2 ~ No. 8 Reserved Set to "0". SW-L1 No. 1 ~ No. 4 Reserved Set to "0". SW-L1 No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [3] Troubleshooting Refer to the following actions to troubleshoot any of problems mentioned in 1-4. • Apply line equalization SOFT SWITCH A5-1, 2. May be used in case [1] [2] [3] [4]. [1] A communication error occurs. • [2] Image distortion produced. Slow down the transmission speed SOFT SWITCH A2-1, 2, 3, 4. May be used in case [2] [3]. [3] Unable to do overseas communication. • Replace the TEL/LIU PWB. May be used in all cases.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [4] Error code table 1. Communication error code table G3 Transmission Code Final received signal Error Condition (Receiver side) 0 Incomplete signal frame Cannot recognize bit stream after flag 1 NSF, DIS Cannot recognize DCS signal by echo etc.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 3-2. Automatic document feed CHAPTER 3. MECHANISM BLOCKS 1) Use of the paper feed roller and separation rubber plate ensures error-free transport and separation of documents. The plate spring presses the document to the paper feed roller to assure smooth feeding of the document. [1] General description 2) Document separation method: Separation rubber plate 1.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Separation rubber 5. Optical system Last page of document (1) General view Rear sheet CCD PWB Document Red mark LED lamp First page of document Paper feed spring Reader glass Paper feed roller Mirror 2 Fig. 4 Mirror 3 3-5. Documents requiring use of document carrier CCD Lens Mirror 1 1) Documents smaller than B6 (128mm x 182mm). Fig. 5 2) Documents thinner than the thickness of 0.06mm.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 6. Recording block (1) General view Take-up side Imaging film Platen roller Pinch roller Guide shaft Thermal head Paper guide PO roller PO guide Supply side RP hopper Rotation plate Main frame PE sensor lever PU roller Separate plate Film sensor lever P-IN sensor lever Fig. 7 6-1.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [2] Disassembly and assembly procedures • • This chapter mainly describes the disassembly procedures. For the assembly procedures, reverse the disassembly procedures. • • The numbers in the illustration, the parts list and the flowchart in a same section are common to each other. Easy and simple disassembly/assembly procedures of some parts and units are omitted. For disassembly and assembly of such parts and units, refer to the Parts List.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 2 Parts list (Fig. 2) Document guide upper No. 1 12 3 13 4 14 5 15 6 16 7 17 8 18 9 19 No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 3 Parts list (Fig. 3) No. Operation panel Part name Q’ty 1 Operation panel unit 1 2 Screw (2.6×6) 5 3 Insulation sheet 1 4 Operation panel PWB unit 1 5 12 key 1 6 Start key 1 7 Stop key 1 8 Mode key 1 9 Direct key 1 10 Panel cable 1 11 Operation panel 1 rib Panel PWB 2 3 Note) Keep the panel PWB to under the rib like a picture.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 4 Parts list (Fig. 4) No. Top cover and head frame unit 1 Part name Mechanism unit 1 2 Top cover unit 1 3 Screw (3×10) 5 4 Head frame unit 1 5 Hopper guide, right 1 6 Hopper guide, left 1 7 Screw 1 8 Pinion gear 1 9 Hopper spring 1 10 Top cover 1 Confirm of HOPPER GUIDE position.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 5 Parts list (Fig. 5) Head frame and thermal head No. 1 4 6 15 3 5 7 16 8 17 9 18 10 19 11 20 3 Q’ty No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 6 Parts list (Fig. 6) No. Paper out guide Part name Q’ty 1 Mechanism unit 1 2 Screw (3×10) 2 3 Paper out guide unit 1 4 Idler gear A 1 5 Take-up gear 1 6 Slip gear ass’y 1 7 Cut washer 1 8 Film shaft C 1 9 PO pinch roller spring 2 10 PO pinch roller 2 11 Clamp 1 12 Paper out guide 1 1 2 11 9 3 10 4 5 6 11 9 10 7 8 2 9 10 7 12 3 9 4 10 12 8 5 6 1 Fig.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 7 Parts list (Fig. 7) Recording paper hopper, speaker and pinch roller No. Q’ty No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Parts list (Fig. 8) No. Main frame, ROM cover, memory cover, drive unit and optical unit 8 Q’ty Mechanism unit 1 2 Screw (3×10) 1 3 ROM cover 1 4 Memory cover 1 5 Screw (3×10) 1 6 Reduction gear B 1 7 Drive unit 1 8 Screw (3×10) 3 9 Main frame unit 1 10 Optical unit 1 11 Clamp 1 2 1 2 Part name 1 4 5 3 6 8 7 4 3 8 9 8 10 9 11 5 7 11 6 Must on the MAIN FRAME to BOTTOM CABINET when combine this GEAR. 10 1 Fig.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Main frame, U turn guide and transfer roller etc. 9 Parts list (Fig. 9) No. Q’ty No. Q’ty No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 10 Parts list (Fig. 10) Drive unit frame No. Q’ty No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 11 Parts list (Fig. 11) Optical frame No. 1 4 7 10 3 5 8 11 6 9 12 No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 12 Parts list (Fig. 12) PWB section No. Part name Q’ty 1 Mechanism unit 1 2 Screw (3×6) 1 3 Earth cable 1 4 Screw (4×6) 1 5 AC cord 1 6 Screw (3×10) 5 7 Connector 2 8 Control PWB unit 1 9 TEL/LIU PWB unit 1 10 Power supply PWB unit 1 11 Shield plate 1 12 Jack sheet 1 2 1 2 7 3 8 4 9 5 10 6 11 12 4 6 6 6 6 3 8 5 6 7 9 7 10 11 12 1 Fig.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 13 Parts list (Fig. 13) Wire treatment No.
4–1 THERMAL HEAD MOTOR CCD LED FILTER SURGE PROTECT FILTER [1] Block diagram DIAL PULSE DRIVER CML CI GPIO I/F MOTOR I/F STABILIZER +24V VREG THERMAL HEAD I/F GPIO I/F CCD I/F SENSOR I/F RECTIFIRE REGULATOR +5V OPERATION PANEL I/F RTC MAIN CONTROL I/F SELECT/AMP BLOCK SPEECH CIRCUIT SW CIRCUIT RCC SYSTEM FEEDBACK CIRCUIT CLOCK MUTE CIRCUIT VBT SURGE ABSORBER LCD INPUT FILTER DRAM MEMORY (4MBIT) OPERATION PANEL SRAM (256KBIT) RECTIFIRE DIODE ROM (2MBIT) SPOUT RX TX
SPEAKER HANDSET TEL LINE EXTERNAL LINE [2] Wiring diagram CNLIU 2 TEL/LIU PWB UNIT MJTEL MJ1/2 14 4–2 LED ARRAY 2 CNLED CNSP CNLIUA CCD PWB 7 CNCCD THERMAL HEAD 16 CNTH CONTROL PWB UNIT CNPN CNDRM (FO-1460U ONLY) FO-1ME OPTION MEMORY (FO-1460U ONLY) 15 TX/RX MOTER OPERATION PANEL PWB 6 2 POWER SUPPLY PWB CN101 CNPN CNMT CNCS CNPW 9 CNLCD 14 LCD UNIT CAM SW.
[3] Point-to-point diagram POWER SUPPLY PWB TEL/LIU PWB MG MG MG +24V +24V DG +5V DG VREG CN101 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 CNLIU +24VA DG PE +5V CML CI HS RHS TXOUT RXIN TELMUTE DRSNS TELOUT TELIN KEN4A KEN3A KEN2A KEN1A DG DG +5V ORGSNS FRSNS E SEN4 SEN3 SEN2 SEN1 SEN0 4–3 CNDRM (FO-1460U ONLY) A9 1 A8 2 A7 3 A6 4 A5 5 A4 6 A3 7 A2 8 A1 9 A0 10 D7 11 D6 12 D5 13 D4 14 D3 15 D2 16 D1 17 D0 18 RAS 19 N.C. 20 CAS2 21 DWR 22 +5V 23 DG 24 +5V 25 DG 26 N.C. 27 N.C. 28 N.C.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 3. Operational description CHAPTER 5. CIRCUIT DESCRIPTION Operational descriptions are given below: • [1] Circuit description When a document is loaded in standby mode, the state of the document sensor is sensed via the 1 chip fax engine (XFCRMVP). If the sensor signal was on, the motor is started to bring the document into the standby position. With depression of the START key in the off-hook state, transmission takes place. 1.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 2) 27C020 (IC3): pin-32 DIP (ROM) [2] Circuit description of control PWB EPROM of 2Mbit equipped with software for the main CPU. 1. General description 3) SRM2B256SLMX70 (IC6): pin-28 SOP (RAM) Fig. 2 shows the functional blocks of the control PWB, which is composed of 5 blocks. Line memory for the main CPU system RAM area and coding/decoding process. Used as the transmission buffer.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U XFCR-MVP (IC4) Terminal descriptions Pin Name Pin No. I/O Input Type Output Type Pin Description (Active low signals have an "n" pin name ending.) CPU Control Interface MIRQn 135 I HU − Modem interrupt, active low. (Hysteresis In, Internal Pullup.) SYSCLK 133 I H − System clock. (Hysteresis In.) TSTCLK 130 O − 3XC A[23:0] [1:6][8:13] [15:20][22:27] O T 3XT Address bus (24-bit). D[7:0] [136:139] [141:144] I/O T 3XT Data bus (8-bit).
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U XFCR-MVP (IC4) Terminal descriptions Pin Name Pin No. I/O Input Type Output Type Pin Description Operator Panel Interface OPO[7:0] [38:40][42:44] [46:47] O − 2XL OPI[3:0] [49:52] I HU − Keyboard/LED strobe [7:0]. Keyboard return [3:0]. (Pullup. Hysteresis In.) LEDCTL 55 O − 4XC Indicates outputs OPO [7:0] are for LEDs. LCDCS 54 O − 1XC LCD chip select.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U (2) Panel control block The following controls are performed by the XFCR-MVP. • • Operation panel key scanning Operation panel LCD display (3) Mechanism/recording control block The following controls are performed by XFCR-MVP.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U (4) Modem (R96DFXL-CID) block FEATURES INTRODUCTION • Group 3 facsimile transmission/reception – – The Rockwell R96DFXL-CID MONOFAX modem is a synchronous 9600 bits per second (bps) half-duplex modem with error detection and DTMF reception. It has low power consumption and requires only a single +5V DC power supply. The modem is housed in a single VLSI device package.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U R96DFXL-CID (IC11) Hardware Interface Signals Pin No.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U (5) Image signal process block CCD VIDEO SIGNAL AMPLIFIER CIRCUIT CLAMP CIRCUIT CLOCK XFCR-MVP VREF+ VREF– Fig. 5 The CCD is driven by the 1-chip engine (XFCR-MVP), and the output video signal from the CCD is input into the XFCR-MVP through the amplifying circuit and clamp circuit. The ADC and buffer are provided in the XFCR-MVP, and the digital image processing is performed.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [3] Circuit description of TEL/LIU PWB (1) TEL/LIU block operational description 1) Block diagram TEL/LIU PWB CONTROL PWB HS CML GAIN-C TXCONT CML TEL LINE SIGTX TXOUT H HS DETECTOR 1 L 0 0 CI DETECTOR EXT. MODEM (R96DFXL-CID) 1 SIGRX RXIN RCVOL HANDSET TEL IN TELOUT VOL A VOL B VOL C BZCONT 0 1 TXCONT SPEAKER RCVOL BZCONT TEL MUTE CI XFCR-MVP GAIN-C SP MUTEI CML TEL MUTE HS CI +5V +24VA DG Fig.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 2. On-hook status detection circuit 7. Signal selection The on-hook status detection circuit detects the Status of the hook switch (RHS) of Built-in telephone, and the status of the hook of a telephone externally connected. • The following signals are used to control the transmission line of TEL/FAX signal. For details, refer to the signal selector matrix table. The status of on-hook switch (RHS) is determined from the logical level of RHS signal.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [Signals for status recognition according to input signals] Signal Name Function H: The handset is in the on-hook state. L: The handset is in the off-hook state. RHS CI Incoming call (CI) detection signal HS H: The handset or external telephone is in the on-hook state. L: The handset or external telephone is in the off-hook state. P.E L: No recording paper. H: Recording paper exists.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [4] Circuit description of power supply PWB 1. Block diagram TRANSFORMER F1 4.0A 125V AC IN 120V 50/60Hz +7.4V CIRCUIT +7.4V +5V CIRCUIT +5V SWITCHING CIRCUIT FILTER/ RECTITYING SMOOTHING CIRCUIT GND +24V CIRCUIT CONTROL CIRCUIT +24V PHOTO COUPLER Fig. 8 The power unit intakes input of AC 120V, 50/60 Hz and supplies output of +24V, +7.4V and +5V as shown in the block diagram. (See Fig. 8.
6–1 B OPI0 OPI1 OPI2 OPI3 LEDCTL LCDCS OPO0 OPO1 OPO2 OPO3 OPO4 OPO5 OPO6 OPO7 C127 C134 C132 C106 +VREF –VREF VIN THADI BZOUT 270 x 4 R120 R118 R116 TPA TPB TPA TPB R112 MPXB R193 R203 N.M.
6–2 1 2 3 4 5 6 (1-3I) (1-3I) (1-6I) (1-5I) A RD ROMCS D[7] ~ D[0] A[18] ~ A[0] TP135 TP136 A[17] A[16] A[15] A[14] A[13] A[12] A[11] A[10] A[9] A[8] A[7] A[6] A[5] A[4] A[3] A[2] A[1] A[0] 6 7 8 9 10 11 12 22 24 30 2 3 29 28 4 25 23 26 27 5 Memory block A B A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 E G B IC3 27C020 R102 0 31 21 20 19 18 17 15 14 13 GND 16 VCC 32 VPP 1 DQ8 DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 (A18) C C192 1 (1-3I) (1-3I) (4-1D) CE1 WR CE2 VBT A[
6–3 B DG N.M GP11 GP02 GP03 GP04 GP05 GP06 GP07 R264 10 MAG R293 R305 270 x 4 R186 VREFCONT 63 100 R299 VOLC 1 R298 VOLB 2 R297 VOLA 3 R296 R291 R300 PIN 4 5 (*1) R290 33K R306 DG BYPASS D R183 10K N.M. TXLOSS1 40 TXLOSS2 39 TXLOSS3 38 DG C190 1 L120 0 E C147 27P XTLI 68 C 62 NC 72 +5VD1 90 86 84 74 26 83 25 85 36 MPXO TELMUTE2 C149 0.
6–4 2 1 VCC 5 IC100 PST596CNR 3 GND 4 4 B R109 1K ORGSNS FRSNS MRST SUB A C111 0.1 +5V CNPN-8 CNPN-9 CNLIUA-12 2 3 1 3 4 B 2 1 DRSNS PE PI2 SG-206S R212 220 PI1 SG-206S CNLIUA-3 +5V +5V R106 220 Other block OUT 1 2 3 4 5 6 A R103 C167 2200P C173 2200P C188 2200P C187 2200P JP2 RBNSNS JP1 PINSNS R114 3 Q100 1 2 R238 270 R251 270 R287 270 R286 270 C C N.M.
6–5 (3-1D) CNCCD-1 +5V A VREFCONT VO R271 33K R241 30K R254 1K E Q102 RNC1402 B C C11 22/50 B C160 0.1 (1-5A) +24V 3 C LEDON IC8 4066 E Q101 DTD114 B C 5 4 R242 150 L108 0 L106 0 +5V D106 1SS355 D VG C133 1 C153 0.
6–6 1 2 3 4 5 6 B (1-1E) (3-3H) (3-3H) (1-5A) (3-3H) (1-5A) A RCVOL AGD SIGRX R195 33K R208 33K +5V +5V C168 1 D104 1SS355 GAINC SIGTX TXCONT 1 B VREF R236 5.6K R252 33K 13 – 6 5 + 2 R215 10K 1 0 3 5 R158 0.1 13 – 12 + IC10 2902 13 12 C156 0.1 1 0 C 11 4 R198 47K 14 R285 62K C166 0.1 C162 0.1 R218 1.5K +24VA R217 20K D TELIN CNLIUB-1 CNLIUA-10 CNLIUA-9 CNLIUA-13 D CNLIUA-14 CNLIUB-6 EXTSIG RXIN TXOUT N.M.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Control PWB parts layout (Top side) 6–7
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Control PWB parts layout (Bottom side) 6–8
6–9 1 2 A MJ2-4 MJ2-3 MJ1-4 +5V C3 1000P JP1 (TP1) JP3 (TP3) TP2 N.M. L4 N.M. L3 B PE SG206S SW2 DRSW SW-168-1AU PC1 PC817X R6 220 ARG SW1 HOOK SW SPPY11029A EXT. R EXT. T RING VA1 ERZVA5D471 3 4 TIP AR1 RA-391P-V6-2 MJ1-3 VA2 ERZVA5D471 5 6 B CI R1 91 R2 30 ZD1 HZ2C1 C CNLIU-8 P.E C CNLIU-3 CNLIU-12 CNLIU-6 RHS DRSNS N.M. L1 N.M.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U TEL/LIU PWB parts layout 6 – 10
A Z1 (ENC241D) 6 – 11 N.M. B C72 4700 Q2 2SC1741AS R5 18K Q1 2SK2972 C1 0.1 C C10 0.01 D10 ERA15-06 R8 33K PC1 PC817B D5 HZS9B C9 4700P R11 6.8K R6 470 R7 180 D R10 6.2K R9 100 D4 1SS133 D7 1SS133 D12 ERA15-06 R12 18K D13 ERA15-06 NTC1 C5 220/200 C71 C7 C8 220P R1 1M L1 LINE FILTER D C6 N.M. C11 220P R17 680 D6 1SS133 R2 390K 1 2 3 5 T1 2C23 9 8 7 E BEA101 C102 330/35 F101 4.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Power supply PWB parts layout 6 – 12
C OD SH DOS OS 3 2 6 – 13 D NS 4 B RS A Φ2 F2802XH-Z8 SS E NC 1 1 NC Φ1 5V NC V0 F NC CCD PWB parts layout F NC AG 22 NC CN1-3 21 NC 2 20 NC R1 2.2K 19 NC C2 0.
6 – 14 C A C1 22000P 11 12 13 1 2 3 4 5 10 C R11 1K R10 6.2K R4 100K B C2 22/50 GND 8 16 VCC A0 D1 A1 D2 A2 D3 A3 D4 D5 N.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Operation panel PWB parts layout 6 – 15
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U CHAPTER 7.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [2] Power on sequence START CPU initialized MODEM initialized “WAIT A MOMENT” display STOP key ? NO “MEMORY CLEAR ?” display NO 3 sec ? YES 1 YES STAND-BY START key ? NO 2 YES COPY key ? 1 2 “MEMORY CLEARED” display “MEMORY CLEARED” display Memory clear Memory clear STAND-BY PROCESS CHECK MODE NO YES STOP key ? NO 3 sec ? NO YES STAND-BY 7–2
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U CHAPTER 8. OTHERS [1] Service tools 1. List DESCRIPTION Q’TY PRICE RANK NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 2. Description 2-1. Extension board unit 1. Remove the TEL/LIU PWB, control PWB and Power Supply PWB from this unit, and mount the extension board unit instead. • Before connecting the wiring to the extension board unit, set the test PWB switches to the fixed position. 2. The setting is as follows. A set with a mounted extension board unit Connector Cable Cable Cable color CNSNS Connected to (PWB) CNPN2 QCNW-4723SCZZ 1.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U H Lightly loosen the red screws of the CCD PWB and obtain the VID 2-2. Scan optical system adjustment signal waveform in synchronization with φT signal waveform. Adjust the CCD PWB positioning to obtain the waveform as shown below. (1) Outline The adjustment procedures of the scan optical system are described below: (2) Adjustment procedures 1 Switch off the machine and disconnect the AC power cable from the wall socket.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U [2] IC signal name CONTROL PWB UNIT IC100: VHiPST596CMT1 (PST596CNR) IC6: VHiS2B256SL70 (SRM2B256SLMX70) (TOP VIEW) VCC 5 OSC T DELAY Q R – 4 VOUT + 3 GND M/R 1 A14 1 28 VCC A12 2 27 W A7 3 26 A13 A6 4 25 A8 A5 5 24 A9 A4 6 23 A11 A3 7 22 S2 A2 8 21 A10 Pin name Signal 20 S1 A0~A12 CE1/CE2 Address input 2 SUB A1 9 A0 10 19 DQ8 DQ1 11 18 DQ7 DQ2 12 17 DQ6 DQ3 13 16 DQ5 GND 14 15 DQ4 Chip enable WE Write enable
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U IC10: VHiNJM2902M-1 (NJM2902M) IC3: VHi27C02012TI (27C020) EP-ROM A OUTPUT 1 A-INPUT 2 14 D OUTPUT (TOP VIEW) A+INPUT V+ B+INPUT B-INPUT B OUTPUT A – + D + – 3 4 11 GND 10 C+INPUT 5 – + B 6 + – C 9 7 8 1 2 OUT/IN 3 IN/OUT 4 C OUTPUT 14 VDD SWD OUT/IN IN/OUT 13 CONT. A 12 CONT. D 5 CONT.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 81 0VD2 82 DCLK 83 EYESYNC 84 EYECLKX 85 EYECLK 86 EYEX 87 ADIN 88 DAOUT 89 0VD2 90 EYEY 91 GP21 92 0VD2 93 GP20 94 GP19 95 RXD 96 RLSDn 97 0VD2 98 RCVO 100 GP02 99 SWGAINO IC11: VHiR96FCRBMVP (96DFXL-CID) 13 68 XTLI D1 14 67 PORin D0 15 66 0VD2 0VD2 16 65 EN85n 0VA 17 64 RTSn RAMPIN 18 63 GP11 NC 19 62 SEE NOTE 1 NC 20 61 GP13 0VA 21 60 RS0 +5VD2 22 59 RS1 0VD1 23 58 RS2 SWGAINI 24 57 RS3 ECLKIN1 25 56 RS4
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U IC7: RH-IX2129SCZZ (IX2129) VHIHM514800J8 PIN DESCRIPTION VCC I/O0 28 VSS 1 PIN I/O1 3 26 I/O6 I/O2 4 25 I/O5 I/O3 5 24 I/O4 NC 6 23 CAS WE 7 22 OE RAS 8 21 NC A9 9 20 A8 A0 10 19 A7 A1 11 18 A6 A2 12 17 A5 A3 13 16 A4 VCC 14 PIN NAME CAS COLUMN ADDRESS STROBE A0~A9 WE READ/WRITE INPUT I/O0~I/O7 DATA I/O OE RAS LOW ADDRESS STROBE VCC POWER (+5V) VSS CONNECTION 27 I/O7 2 PIN PIN NAME ADDRESS INPUT (LOW/REFRESH A0~A3
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U PARTS GUIDE MODEL UX-510 UX-500 FO-1460 CONTENTS 1 Cabinet, etc.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 1 Cabinet, etc.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Cabinet, etc. 1 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Cabinet, etc. 1 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 2 Upper cabinet 3 12 7 4 5 6 1 11 B1 8 2 B1 B1 Upper cabinet 2 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Document guide upper 3 4 12 4 2 14 7 1 5 6 8 15 13 8 10 3 11 16 9 Document guide upper 3 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 4 Optical unit 12 5 10 3 14 12 B8 6 1 13 4 2 9 11 11 7 8 Optical unit 4 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Drive unit 5 B2 B2 7 5 4 3 12 13 9 8 7 10 2 6 1 11 11 9 Drive unit 5 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 6 Head unit 1 W1 6 4 16 B6 9 5 3 15 5 16 B6 7 13 10 12 B2 14 11 8 2 Head unit 6 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 7 Packing material & Accessories 7 3 9 TAPE TAPE TAPE 6 2 8 1 16 15 22 4 5 18 15 15 7 AC CORD AC CORD TAPE 12 14 IMAGING FILM UNIT TAPE 13 10 21 11 Packing material & Accessories 7 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Control PWB unit 8 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Control PWB unit 8 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Control PWB unit 8 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Control PWB unit 8 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U Control PWB unit 8 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U TEL-Liu PWB unit 9 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U 10 Power supply PWB unit NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U ■ Index PARTS CODE [C] CCNW-4695AX01 CGERH2314AX51 CGERH2363AX01 CLEVP2254AX01 CLEVP2255AX01 CLEVP2256AX01 CPNLH2380AX01 ″ CPNLH2380AX02 ″ CPNLH2380AX06 ″ CROLP2334AX01 CROLR2362AX01 CROLR2363AX01 [D] DCEKC382JAXZZ ″ DCEKC582JAXZZ ″ DCEKC583JAXZZ ″ DCEKD475AAX05 ″ DCEKL349BAX01 ″ DCEKP351BAX01 DCYOD475AAX02 DUNTK307BAXBE DUNTK307BAXOG DUNTK307BAXOW [G] GCABA2289AXSA GCABA2289AXSB GCABA2289AXSC GCABB2290AXSA GCABB2290AXSB GCABB2290AXSC GCABC2291AXSA GCABC2291AXSB GCA
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U PARTS CODE QSW-Z2226SCZZ [R] RC-FZ3024SCZZ RCILZ2104SCZZ RCORF2063XHZZ RCORF2064XHZZ RCRSB0297AFZZ RCRSP2119SCZZ RCRSQ1005LCZZ RDENT2112AXZZ ″ RH-IX2129SCZZ RHEDZ2052AXZZ RMOTZ2131AXZZ RRLYD3130SCZZ RRLYD3221SCZZ RTRNZ2128XH01 [S] SPAKA110AAXZZ SPAKA111AAXZZ SPAKA114AAXZZ SPAKA213AAXZZ SPAKC115AAXZZ SPAKC128AAXZZ SPAKC165AAXZZ SPAKC167AAXZZ SPAKC198AAXZZ SPAKP4381AXZZ [T] TCADZ2513AXZZ TCADZ2528AXZZ TINSE3717AXZZ TINSE3747AXZZ TINSK3746AXZZ TLABH4161AXZZ TLABH4163AX
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U PARTS CODE VRS-TS2AD000J ″ ″ ″ ″ ″ VRS-TS2AD100J ″ ″ VRS-TS2AD102J ″ ″ ″ ″ ″ ″ VRS-TS2AD103J ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ ″ VRS-TS2AD104J ″ VRS-TS2AD105J VRS-TS2AD106J VRS-TS2AD121J VRS-TS2AD133J VRS-TS2AD151J ″ ″ ″ ″ ″ ″ ″ ″ VRS-TS2AD152J VRS-TS2AD154J VRS-TS2AD183J VRS-TS2AD201J ″ ″ ″ VRS-TS2AD203J ″ ″ ″ ″ VRS-TS2AD221J ″ ″ ″ ″ ″ ″ NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U PARTS CODE 0KY0MPS027700 0KY0M131A0020 0KY0M850A0010 ″ 0KY0R153U1010 0KY0R153U1020 0KY0R153U1050 0KY0R153U1810 0KY0R153U1830 ″ 0KY0R153U2430 0KY0R153U3310 0KY0R153U3330 0KY0R153U3340 0KY0R153U3920 ″ ″ 0KY0R153U3940 0KY0R153U4710 0KY0R153U4720 0KY0R153U6220 0KY0R153U6810 0KY0R153U8220 0KY0R353U1130 0KY0R854E5020 0KY0T351A0050 0KY0T358A0040 0KY0T644A0010 NO.
UX-510U/UX-510C/UX-500U UX-500C/FO-1460U COPYRIGHT © 1997 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.