cover_NX-PN10[C].
safety_NX-PN10[C].fm Page 1 Monday, April 27, 2009 4:22 PM Warnings, Cautions and Others Mises en garde, précautions et indications diverses CAUTION The button in any position does not disconnect the mains line. Disconnect the mains plug to shut the power off completely (the STANDBY lamp goes off). The MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. • When the system is on standby, the STANDBY lamp lights red.
safety_NX-PN10[C].fm Page 2 Monday, April 27, 2009 4:22 PM For Canada/pour le Canada THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,” ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
safety_NX-PN10[C].fm Page 3 Monday, April 27, 2009 4:22 PM Caution: Proper Ventilation To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows: 1. Front: No obstructions and open spacing. 2. Sides/Top/Back: No obstructions should be placed in the areas shown by the dimensions below. 3. Bottom: Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
NX-PN10[C].BOOK Page 1 Tuesday, April 28, 2009 11:17 AM Contents Introduction................................................. 2 Precautions ................................................................ 2 Getting Started............................................ 3 Connections................................................................ 4 Canceling the Display Demonstration (Demo) .......... 6 Turning on the Power Automatically (Motion Sensor) ..................................................
NX-PN10[C].BOOK Page 2 Tuesday, April 28, 2009 11:17 AM Introduction Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best possible performance from the unit. Precautions Installation • Install in a place which is level, dry and neither too hot nor too cold—between 5°C and 35°C. • Install the unit in a location with adequate ventilation to prevent internal heat buildup inside the unit.
NX-PN10[C].BOOK Page 3 Tuesday, April 28, 2009 11:17 AM Getting Started • In this manual, operations using the remote control are mainly explained; however, you can use the buttons and controls on the unit if they have the same (or similar) name and marks. • In this manual, “iPod” means both iPod and iPhone devices. When iPhone device is especially mentioned, “iPhone” is used in this case.
NX-PN10[C].BOOK Page 4 Tuesday, April 28, 2009 11:17 AM Connections Do not connect the AC power cord until all other connections have been made. Connecting the Antenna FM antenna (supplied): Extend it so that you can obtain the best reception. Rear side For better FM reception Disconnect the supplied FM antenna and connect to an outdoor FM antenna using a 75 Ω wire with coaxial type connector.
NX-PN10[C].BOOK Page 5 Tuesday, April 28, 2009 11:17 AM Connecting the Video Cord to View a Video/Picture from iPod When viewing a video/picture from iPod on your TV, use a composite video cord (not supplied) to connect the VIDEO OUT jack on the unit and the composite video input on your TV. • After you have connected the unit, change the video input mode on your TV. For details, also refer to the instruction manual for your TV.
NX-PN10[C].BOOK Page 6 Tuesday, April 28, 2009 11:17 AM Canceling the Display Demonstration (Demo) When you connect the AC power cord for the first time, the display demonstration starts automatically. • When you operate the unit, the display demonstration stops temporarily. If no operation is done for about 2 minutes, the unit starts the display demonstration again. Button Operation On the unit Hold down until “DEMO OFF” appears on the display.
NX-PN10[C].BOOK Page 7 Tuesday, April 28, 2009 11:17 AM Basic Operations Main Unit Illumination panel (P.10) Dock A (P.13) Dock B (P.13) Motion sensor (P.6) Display (P.8) Remote control sensor STANDBY lamp Operating on the Main Unit Buttons Operations Turns on or off (standby) the power. Activates or deactivates Motion Sensor (P.6).
NX-PN10[C].BOOK Page 8 Tuesday, April 28, 2009 11:17 AM Buttons Operations Activates or deactivates the display demonstration (P.6). Adds the powerfulness to the sound (P.11). Stops the timer sound and restarts it 5 minutes later (P.22). • iPod (P.14): Press: Reverse skip/forward skip. Hold down: Reverse search/forward search. • FM (P.17): Tunes in to a station. • Changes the source to iPod /iPod (P.14). • Starts playback and pauses for iPod (P.14). Changes the source to FM (P.17) or AUDIO IN (P.19).
NX-PN10[C].BOOK Page 9 Tuesday, April 28, 2009 11:17 AM Symbols Description ST Lights up when FM stereo broadcast is received. MONO Lights up when FM monaural reception mode is activated. TUNED Lights up when an FM station of sufficient signal strength is tuned in. FM Lights up when FM is selected as the source. 1/2/3 SLEEP • Lights up when Timer is set (P.21). • 1/2/3 icon flashes while Timer is working. Lights up when Sleep Timer is activated (P.11). Remote Control P.10 P.11 P.20, P.22 P.
NX-PN10[C].BOOK Page 10 Tuesday, April 28, 2009 11:17 AM Buttons Main operations Changes the display information. • For iPod A/iPod B/AUDIO IN: • When the unit is turned off: Source name Clock Day of the week Clock Day of the week • For FM: Frequency Clock Day of the week Changes the source to FM (P.17) or AUDIO IN (P.19). • Changes the source to iPod /iPod (P.14). • Starts playback and pauses for iPod (P.14). Adjusts the volume level (VOL MIN/VOL 0 to VOL MAX/VOL 30).
NX-PN10[C].BOOK Page 11 Tuesday, April 28, 2009 11:17 AM To turn off the unit after a certain period of time—Sleep Timer Press repeatedly to specify the time (in minutes) as follows: 10 30 20 OFF (Canceled) 180 60 150 90 120 • To check the time remaining before the shut-off time, press SLEEP once. If you press the button repeatedly, you can change the shut-off time. To emphasize the sound—Sound Turbo You can add the powerfulness to the sound. Press to activate Sound Turbo.
NX-PN10[C].BOOK Page 12 Tuesday, April 28, 2009 11:17 AM Playing Back from iPod Devices You can connect 2 iPod devices to the unit and enjoy sound and video from them.
NX-PN10[C].BOOK Page 13 Tuesday, April 28, 2009 11:17 AM Connecting iPod Connect iPod to dock A or B on the unit. You can have 2 iPod devices connected at the same time. • Make sure the unit is on standby when you connect iPod. Dock adapter (supplied with iPod or sold separately) Dock A Dock B To detach the dock adapter from the dock: Pull up the dock adapter with your fingernail or a sharp-pointed tool using the slot. • Be careful not to injure your fingertips or damage the terminal of the dock.
NX-PN10[C].BOOK Page 14 Tuesday, April 28, 2009 11:17 AM Operations For details, also refer to the instruction manual for iPod. NOTES: • Before viewing a video/picture from iPod on your TV, make the appropriate video setting on iPod. For details of the setting, see the instruction manual for iPod.
NX-PN10[C].BOOK Page 15 Tuesday, April 28, 2009 11:17 AM Buttons On the unit Operations On the remote Confirms an item on the menu/screen. — * Control of iPod Center button* — Press: Applies Shuffle Play to iPod or iPod selected as the source. Select the desired shuffle mode. “SHUFFLE” appears for a while. • The shuffle icon lights up on the display of iPod. • To cancel, press again until the shuffle icon disappears. Hold down: Applies Shuffle Play to both iPod and iPod if connected.
NX-PN10[C].BOOK Page 16 Tuesday, April 28, 2009 11:17 AM NOTES: • JVC is not responsible for any loss of or damage to iPod that might result from the use of this product. • Do not touch or hit the terminals of the dock and of iPod. It might cause damage to these terminals. • When you connect iPod to the dock, make sure the terminal on the dock is fully inserted into iPod. • Always set the volume to the minimum level when connecting or disconnecting iPod. • Do not carry the unit with iPod connected.
NX-PN10[C].BOOK Page 17 Tuesday, April 28, 2009 11:17 AM Listening to FM Broadcasts Basic Operations Buttons Operations On the unit On the remote Selects FM as the source. FM AUDIO IN When an FM program is broadcasted in stereo, ST (stereo) lights up on the display (only when the reception is good). Press: Changes the frequency. Hold down and release: The unit starts searching for stations and stops when a station of sufficient signal strength is found. • To stop searching, press again.
NX-PN10[C].BOOK Page 18 Tuesday, April 28, 2009 11:17 AM Presetting Stations You can preset 30 FM stations. 1 Select FM as the source. 2 Tune in to the station you want to preset. • You can also store the monaural reception mode for FM preset stations if selected. 3 Activate the preset number entry mode. “SET” flashes on the display for a few seconds. • Complete the following operations while the indication is flashing. Select a preset number for the station you want to store.
NX-PN10[C].BOOK Page 19 Tuesday, April 28, 2009 11:17 AM Playing Back from Other Equipment Connecting Other Equipment By using a stereo mini plug cord (not supplied), you can connect other equipment with analog audio output jacks, such as a portable audio player, etc. To headphones or audio out Stereo mini plug cord (not supplied) Portable audio player Rear side • Refer to the instruction manual supplied with the equipment.
NX-PN10[C].BOOK Page 20 Tuesday, April 28, 2009 11:17 AM Setting the Clock and Timer Setting the Clock Set the built-in clock before using Timer. • You can set the clock when the unit is turned on or on standby. 1 Activate the clock setting mode. “ADJCLOCK” appears then the hour digit of the time indication flashes on the display. • If you have already set the clock before, press the button twice to activate the clock setting mode.
NX-PN10[C].BOOK Page 21 Tuesday, April 28, 2009 11:17 AM Select Timer you want to set. TIMER 1 2 TIMER 2 TIMER 3 Select Timer type. WEEKLY 3 ONCE WEEKLY: See step 4 below. ONCE: Timer works once on a selected day of the week. Select the desired day of the week. • When “WEEKLY” is selected in step 3: SUN DAY THU DAY MON-SAT 4 MON DAY FRI DAY EVERYDAY WED DAY TUE DAY SAT DAY MON-FRI Back to the beginning SUN DAY to SAT DAY: Timer works every week on the selected day.
NX-PN10[C].BOOK Page 22 Tuesday, April 28, 2009 11:17 AM To Cancel Timer Select Timer you want to cancel. TIMER 1 1 2 TIMER 2 TIMER 3 “CANCEL” flashes on the display. The icon and the timer number indicator (1/2/3) disappear. NOTE: The settings you have made are memorized though you cancel Timer. To Turn off the Timer Sound briefly—Snooze Using Snooze, you can have the timer sound stop and restart it 5 minutes later. 1 Set Timer following the steps 1 to 6 on pages 20 and 21.
NX-PN10[C].BOOK Page 23 Tuesday, April 28, 2009 11:17 AM Troubleshooting If you have a problem with your unit, check this list for a possible solution before calling for service. General iPod Operations Power does not come on. iPod doesn’t play though iPod /iPod The power plug is not inserted securely. Plug lights up on the display. it in securely (P.5). The battery is empty. Leave it connected for more than 10 minutes. Power turns on even though you turned off. Motion Sensor is activated (P.6).
NX-PN10[C].BOOK Page 24 Tuesday, April 28, 2009 11:17 AM Specifications Accessories Main Unit See page 3. Output Power 10 W (5W+5W) at 8 Ω (10%THD) Dimensions (W/H/D): 326 mm × 135 mm × 130 mm Mass: Approx. 1.6 kg Terminals Speaker Specifications AUDIO IN Input Sensitivity/Impedance (1 kHz): LEVEL 1: 500 mV/47 kΩ LEVEL 2: 315 mV/47 kΩ LEVEL 3: 125 mV/47 kΩ Dock A and B for iPod/iPhone Compatible iPod/iPhone models: See page 12.
cover_NX-PN10[C].
