Service manual

AR-235/275 SIMULATION - 33
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTER-
RUPT] key is inhibited.
Operation/procedure (Pattern 2)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Operation/procedure (Pattern 5)
Select the mode with the arrow keys, enter the adjustment value with
the 10-key, and press the [OK] key.
When the [START] key is pressed, a print is made and the display
returns to the mode selection menu.
Setup of various copy conditions: Similar to the normal copy mode.
Use of [SPECIAL FUNCTION] key, [JOB STATUS] key, and [INTER-
RUPT] key is inhibited.
Operation/procedure (Pattern 1)
Enter the adjustment value with the 10-key and press the [OK] key, and
the entered value is registered.
Operation/procedure
Pressing the [OK] key performs the LSU test.
Used to set the LSU to ON state and check that the sync signal
(HSYNC/) is outputted or not.
After operation for 30 sec, the result is displayed. (Interruption cannot
be made for 5 sec after starting the operation.)
Operation/procedure
Pressing the [OK] key performs shading, and displays the result (cen-
ter pixel).
Display items Content Setting range Default
1:OC
OC 1-99 50
2:SPF(SIDE1)
SPF front surface
3:SPF(SIDE2)
SPF back surface
51
51-1
Purpose
Adjustment
Function
(Purpose)
Used to adjust the OPC drum separation pawl ON
time.
Section
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Item
Operation
(Initial screen) (Input screen)
Display items Setting range Default
1:600dpi
1-99 50
2:1200dpi
51-2
Purpose
Adjustment
Function
(Purpose)
Used to adjust the contact pressure of paper onto the
resist roller in each section (copier paper feed section,
duplex paper feed section, SPF paper feed section).
(When the print image position varies greatly for the
paper or when a lot of paper jam troubles occur, the
adjustment is required.)
Section
Paper transport (Discharge/Switchback/Transport)
Item
Operation
(Initial screen) (Input screen) (Executing screen)
Display items Content Setting range Default
1:BYPASS
Manual feed 1-99 50
2:TRAY1
1st cassette
3:TRAY2
2nd cassette
4:TRAY3
3rd cassette
5:TRAY4
4th cassette
6:DUPLEX
Back print
7:SPF(SIDE1)
SPF front surface
8:SPF(SIDE2)
SPF back surface
Sim51-1 D/F TIMING
1:600dpi 50
2:1200dpi 50
2
Sim51-1 D/F TIMING
2:1200dpi 50
[ 1- 99] 50
Sim51-2 RESIST ADJ.
1:BYPASS 50
2:TRAY1 50
3:TRAY2 50
1/3 50
51-8
Purpose
Setting
Function
(Purpose)
Used to set to disable the operation of the separation
pawl of the photoconductor drum.
Section
Image process (Photoconductor/Developing/Transfer/
Cleaning)
Item
Operation
Display items Content Setting range Default
0:ON
Enable 0-1 0
1:OFF
Disable
61
61-1
Purpose
Operation test/check
Function
(Purpose)
Used to test the operation of the LSU.
Section
LSU
Item
Operation
(Initial screen) (Executing screen)
Interruption is inhibited
during execution.
During execution,
[EXEC] is highlighted.
(Result screen/Normal) (Result screen/Abnormal)
63
63-1
Purpose
Adjustment/setting/operation data output/check
(display/print)
Function
(Purpose)
Used to check the result of shading correction. (The
shading correction data are displayed.)
Section
Scanner (Exposure)
Item
Operation
Sim51-8 D/F SETTING
DETACH FINGER 0
(0:ON
1:OFF)
[ 0- 1] 1
Sim61-1 LSU CHECK
PRESS OK KEY EXEC
Sim61-1 LSU CHECK
EXEC
Sim61-1 LSU CHECK
COMPLETE EXEC
Sim61-1 LSU CHECK
ERROR EXEC