ASSEMBLY INSTRUCTIONS UltraGraphiteTM Mobile Workbench (Model No. WEB484) 48 in W X 24 in D X 37.5 in H (1.21 m x 60.9 cm x 82.
PARTS LIST (pg 1 of 7) Please check the parts carefully according to the parts list. If you are missing any parts, please contact our customer service department (please refer to page 7 of 7). M8X20 pcs #15 #27-B #40 #50 #21 #25 Drawer Parts No. Qty. Parts No. Qty.
Assembly Instructions (pg 2 of 7) UltraGraphiteTM Mobile Workbench (Model No. WEB484) Note: We recommend TWO people to assemble the workbench. Tip: A magnetic screwdriver is included for your convenience. If a power screwdriver is used, keep on low torque setting. Step 1: Install (#5-B) Leg Piece. A: Open the package, and put the parts aside. Then, attach the (#47) "L" Bracket to the (#5-B) Leg Piece, use (#50) Screw I to tighten. Repeat Step A to install (#47) "L" Brackets to another one (#5-B) Leg Piece.
Assembly Instructions (pg 3 of 7) UltraGraphiteTM Mobile Workbench (Model No. WEB484) Step 3: Install (#3-B) Bottom Cross Bar and (#11) Swivel Wheel with Brake & (#13) Swivel Wheel w/o Brake. Back Attach the (#3-B) Bottom Cross Bar to the back of (#5) Leg Piece, line up the screw holes, use (#40) Screw E with (#27-B) Washer and (#25) Wrench to tighten. After installing (#5-B) Leg Pieces, attach (#11) Swivel Wheel with Brake & (#13) Swivel Wheel w/o Brake to (#5-B) Leg Pieces, use Wrench (#25) to tighten.
Assembly Instructions (pg 4 of 7) UltraGraphiteTM Mobile Workbench (Model No. WEB484) Step 6: Install (#20-6) Drawer Front Panel Support Plate Attach (#20-6) Drawer Front Panel Support Plate as the left arrow shows. Line up the screw holes and use (#15) Screw B to tighten. #20-6 Front NOTE: Make sure the hook slots on the (#20-6) Drawer Front Panel Support Plate are facing inward. #19-2 NOTE: Once you adjust all the parts in position, tighten all screws.
Assembly Instructions (pg 5 of 7) UltraGraphiteTM Mobile Workbench (Model No. WEB484) Step 8: Insert Drawer Pull out the drawer sliders to full length, then attach and fit the Drawer to the inner track of the sliders and slide drawers in. NOTE: Make sure to remove the rubber guards on the hooks of the inner track before fitting the drawer in. Once you insert the drawers, tighten (#15) Screw B for (#48-2) Small Drawer Left Support and (#48-3) Small Drawer Right Support.
Assembly Instructions (pg 6 of 7) UltraGraphite TM Mobile Workbench (Model No. WEB484) Step 10: Install (#20-7) Drawer Divider Insert Drawer Divider into the drawer. The solid wall of the divider should be facing the desired slot position. Slide the divider towards the slot, then push down into the slots. Repeat the above steps to assemble another Drawer Divider.
CONTACT INFORMATION (pg 7 of 7) *If you are missing any parts, have any questions, or need additional assistance in assembly, please contact our bilingual (English/Spanish) customer service department at: Seville Classics, Inc. 19401 South Harborgate Way Torrance, CA 90501 USA Telephone: (800) 323-5565 within USA Hours: 9:00am - 4:30pm (Pacific Standard Time) Fax: (310) 533-3899 E-mail: support@sevilleclassics.com Website & Online Store: www.sevilleclassics.
Model No. 20225 Rolling Cabinet Model No. 20296 Height Adjustable Workbench Model No. 20230 Wall Cabinet Model No. 20262 Rolling Workbench Model No. 20217 Trash Bin Model No.