Installation manual

6 R
EFERENCE
& I
NSTALLATION
M
ANUAL
The integrity of a security system relies not only in the performance of the
control panel, keypads, motion detectors and other accessories, but in the
ability to communicate information effectively back and forth through the
system's wiring. With this in mind Paradox Security Systems created the
next evolution in control panel technology: DigiplexNE.
DigiplexNE uses
GuardWall Technology, a specialized encrypted communication protocol to
transmit data efficiently between the control panel and all its modules
simultaneously and continuously. Since data is constantly transmitted
through the 4-wire communication network, any attempt to tamper with or
disable any module or the wiring is immediately recognized and causes an
alarm to be reported whether the system is armed or not.
DigiplexNE also offers the additional benefit of an innovative built-in access
control system. Manage, control and monitor the traffic of up to 999 users
through 32 secured areas by defining the days and times they are allowed
access. By integrating access control and security, DigiplexNE provides the
best of both worlds in a feature-rich and user-friendly system.
Beyond offering high security, Guardwall technology makes installing and
programming effortless by eliminating the need for home run wiring,
jumpers and EOL resistors. Connect the modules with GuardWall
technology in any order anywhere on the communication network and
assign the zones as desired. Since programming a large security system
through a keypad can be time consuming and tedious, installers can use
the WinLoad software to complete all the programming remotely, including
setting a motion detector's sensitivity. Even users can modify their security
system through the comfort of their own computer with NEware, a simple,
intuitive interface designed to add employees, set schedules, assign
access rights, view the status of the system and all its modules and more.
CTR-21 APPROVAL
The DigiplexNE control panel (DGP-96) meets the European Union
Common Technical Requirement CTR-21. The CTR-21 requirement is an
electrical standard that defines the analogue interface for all two-wire
telecommunications equipment (i.e. DECT, PABXs, etc.) intended for
connection to the Public Switched Telephone Network. This allows the
DigiplexNE control panel to be used in as many as 19 countries, such as
Belgium, Germany, Greece, Portugal, Sweden and Switzerland.
DigiplexNE control panels with the CTR-21 approval are available as an
option only.
1.1 F
EATURES
GuardWall technology:
• Digital communication network
• Provides constant power, supervision and two-way communication
between the control panel and all its modules
• Supports up to 127 modules
• Connect modules up to 3000ft (914m) from the panel
• Sabotage-proof technology without additional wiring
96 addressable zones
8 partitions
998 user codes, 1 System Master code and 1 installer code
Built-in access control
2048 stored events
1 telephone line and optional secondary telephone line
Remote diagnostics and pager messaging
False alarm prevention features
32 independent keyswitch zones (does not use any of the 96 zones)
8 on-board hardwired input terminals
3 on-board fully programmable outputs (PGMs):
• 1 normally open, high-current transistor output (100mA)
• 2 normally open or normally closed 5A programmable relay outputs
• Up to 32 more PGM inputs through the Keyswitch’s PGM Input
feature
PGM1 can be set as a two-wire smoke detector input
Event reporting:
• a separate dialing sequence for each partition
• 4 Monitoring Station Telephone Numbers
• SIA, Contact ID, Ademco Contact ID Edition 2000, Pager Format
and many more communicator formats
1.2 S
PECIFICATIONS
C
ONTROL
P
ANEL
AC Power: 16Vac, 20/40VA, 50-60Hz
Battery: 12Vdc, 4Ah minimum
Auxiliary Power: 12Vdc 600mA typical, 700mA maximum,
fuseless shutdown at 1.1A
Bell Output: 1A, fuseless shutdown @ 3A
PGM Output: PGM1 (100mA), PGM2 and PGM3 (5A relay)
Event Buffer: 2048 events
All control panel outputs are rated to operate between 10.8Vdc and
12.1Vdc
1.3 K
EYPAD
S
PECIFICATIONS
Power input: 9-16 Vdc
Typ. current consumption: 60mA (DGP2-641)
150mA (DGP2-641AC)
PGM current limit: 50 mA
Number of inputs: 1 (DGP2-641)
2 (DGP2-641AC)
Power indication: Yellow LED on
Locate indication:
Green and yellow LEDs flash simultaneously
Network fault indication: Red and yellow LEDs flash alternately
Tamper Switch: Yes (also used to deactivate locate)
LCD: Super Twisted Nematic display (STN), wide
viewing angle, 2 lines of 16 characters,
adjustable scrolling speed, backlight and
contrast