GALAXY 5000RS/2000RS SERIES-DBP DATA BUS PORT VEHICLE SECURITY SYSTEM WITH REMOTE START PRODUCT MANUAL
Limited Lifetime Warranty This vehicle security system is warranted to the original purchaser, to be free from defects in material and workmanship. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid.
Table of Contents 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. About Your System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 1 Remote Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 2 Remote Transmitter Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3 Adding/Replacing Transmitters . . . . . .
About Your System The ScyTek Galaxy 5000RS-DBP Series is a Combination Vehicle Security and Remote Starting System , Galaxy 2000RS-DBP Series is a Remote Starting with keyless entry. featuring a built-in "ScyNet Network Port" that allows direct connection of optional accessory modules and a PC interface offering expanded system operation. With proper installation this system will provide superior protection and performance for many years to come.
Remote Transmitters Standard Remote Transmitter Description LED LED Button 2 Button 1 Button 1 Button 2 Button 3 Button 4 Button 5 Button 3 Button 4 Button 5 T5-SP T5 Depending on the model chosen, the Galaxy 5000/2000RS-DBP Series will be supplied with one or two T5 or T5-SP 5-button Remote Transmitters that are used to control the system’s operations.
Adding/Replacing Standard Remote Transmitters To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired transmitters ready and follow the steps below. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter will be erased if it is not programed within the following sequence To program the transmitter(s): 1. Turn the ignition key On, Off, On, Off, and back On.
2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 Depending on the model chosen, the Galaxy 5000/2000RS-DBP-2W Series will be supplied with one or two 2-way LCD Remote Transmitters, offering increased range and confirmation of any activated features. Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks the system.
· The LED will illuminate. 3. Press and release Button 1 on the first transmitter then on the second transmitter. · The siren/horn will chirp/honk once for every transmitter learned. 4. Turn off the ignition key. 5. The siren/horn will chirp/honk 3 times to indicate the system has exited programming mode. LCD Transmitter Battery Replacement Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time.
To set the daily start feature: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. · The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 2 until the desired hour is displayed. 3. Press Button 3 until the desired minute is displayed. The button may be held down to scroll faster. 4. When the desired time is displayed, press Button 5 to store. · The remote will beep 3 times to indicate the daily start function has been set.
CHP Set the siren/horn confirmation chirps/honks ON or OFF: 1. Press and hold Button 5 until the display shows CHP. ·The transmitter will beep three times. 2. Release Button 5. · The transmitter will beep once. · The LCD panel will show a siren if the chirps*/honks are enabled or "off" if the chirps*/honks are disabled. SND sound function selects the transmitter's confirmation mode - Tone or Vibration mode. Set the transmitter confirmation tones ON or OFF: 1.
Page 8 - Galaxy 5000/2000RS-DBP
OPtional Color Remote time date/engine run timer 11/16 3:10P Button 3 Button 4 Button 1 Button 5 Button 2 Battery status wakeup alarm enabled autostart enabled Optional 2-way Color remote transmitter is offering increased range and confirmation of any activated feature. Page 1 Button 1 Arms and Locks* the system and when held for 3 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. Button 2 Disarms and Unlocks* the system.
PAGER PARAMETERS SETTING Press and hold Buttons 2 and 3 until pager program features are displayed. Select pager. pager setting by pressing buttons 1 or 2 to highlight the remote pager. Press button 3 to select the Setting Date & Time TIME DATE START TIME ALARM CLOCK SOUND ON BACK Select Time Date setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
Use buttons 1 & 2 to highlight the time parameter you wish to change, use buttons 3 & 4 to scroll up or down to chage the time. Save the changes by pressing button 5. START SET AUTO ST ON TIME: 08:00A Setting Alarm Clock Select Alarm setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. TIME DATE START TIME ALARM CLOCK SOUND ON BACK Enable/Disable Alarm Select Alarm Clock on/off by pressing button 3.
Return to Previous Screen Select Previous Screen by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. TIME DATE START TIME ALARM CLOCK SOUND ON BACK Press and hold Buttons 2 and 3 until pager program features are displayed. Select system setting by pressing buttons 1 or 2 to highlight the siren. Press button 3 to select the system features. Siren Chirp Enable/Disable Select Siren Chirp setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
Setting AutoStart Cold Temperature Threshold Select Cold Temp start setting by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. SIREN CHIRP PASSIVE ARM COLD TEMP HOT TEMP BACK Use buttons 3 & 4 to scroll up or down to chage the temperature threshold. Save the changes by pressing button 5. AUTOSTART SET COLD TEMP TEMP: - 11oF Security system responce Setting AutoStart Hot Temperature Threshold Select Cold Temp Time setting by pressing buttons 1 or 2 to highlight the feature.
Synchronize System and Pager Clocks Select Clock Sync setting by pressing buttons 1 or 2 to highlight the arrows. Press button 3 to select the pager. Pager Clock Sync This feature synchronizes the pager clock to the security system time of a day clock. Select Pager Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it.
START 1 SET SET TIME TIME: 8:00A Use buttons 1 & 2 to highlight Set Time press button 3. AUTOSTART 1 TIME: 8:00A The security system responce. Start Time 2 This feature sets the system Autostart 2 time. Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature. Press button 3 to select it. PGR CLK SYNC SYS CLK SYNC START 1 TIME START 2 TIME EXIT Use buttons 1 & 2 to highlight hours or minutes, use buttons 3 & 4 to scroll up or down to chage the time.
Programmable Functions using the Color Remote Pressing and holding transmitter button 5 will scroll through several transmitter programmable options - TEMPERATURE, ENABLE COLD START, ENABLE HOT START, VALET MODE, ENABLE AUTOSTART 1, ENABLE AUTOSTART 2. TEMPERATURE Check the temperature inside the vehicle 1. Press and hold Button 5 until the display shows TEMPERATURE 2. Release Button 5. · The transmitter will beep four times. ENABLE COLD START Auto Start Cold Temperature Activation Mode.
Transmitter Lockout ADDITIONAL FUNCTION Press and hold buttons 2 & 4 simultanously for 3 seconds to lockout the transmitter against accidental transmission. Release Transmitter Lockout Press and hold buttons 2 & 4 simultanously for 3 seconds to release the transmitter from Lockout. Out of Range Report pager report if no responce from the unit.
Pager Status Display Time: time of day clock Date/Engine Run Timer: date, or engine run minute timer if remote start activated (20 min max). Battery Status: displays remaining battery life.
System Operation Remote Arming/Locking The system monitors 5 independent areas (zones) while armed: doors, hood/ trunk, shock sensor, optional sensor input, and the network port for future expansion. To Arm and Lock the System: 1. Turn off the ignition. 2. Press Button 1. · The siren/horn will chirp/honk once. · The doors will lock. · The parking lights will flash once. · The LED will turn ON, to indicate the starter defeat is activated. 3.
Tamper Alert If the system was triggered while away, the LED will flash to indicate which zone triggered the system after disarming and turning the ignition ON. The LED indication will repeat 8 times.
Panic Mode In the event of an emergency, the transmitter’s remote Panic feature can be used to instantly trigger the alarm/panic feature. To activate the Panic Mode: 1. Press and hold Button 1 for five seconds. · The alarm will sound. · The parking lights will flash. · The doors will unlock** allowing access to the vehicle. 2. Press Button 1 or 2 to stop Panic Mode. ** If the ignition is on when the Panic feature is activated, the doors will lock for personal safety.
3. Press the valet switch 4 times. · The siren will chirp each time the valet switch is pressed. 4. Within 5 seconds, press Button 3 on the transmitter. · The siren will chirp 3 times. 5. Press the valet switch the number of times equal to the desired code (from 1-15). 6. Turn off the ignition then arm the system. 7. Disarm the system using the new Override Code to permanently store the new code. Note: If the code set procedure is not properly performed, turn off the ignition and begin again.
Remote Start Features Remote Starting To Remote Start the System: 1. Be sure the system is not in Valet Mode. 2. Press and hold Button 4 for three seconds. · The parking lights will flash 4 times and turn on. · The siren/horn will chirp/honk 4 times. ( if enabled, see page 23 branch 9 ) · The engine will start and run for the duration of its programmed Run Time.** · The heater or air conditioner will turn on (if turned on prior to exiting the vehicle).
Automatic Start Mode Automatic Start feature has three modes that will start the vehicle every one or two hours within a 24 hour period. 1. Timer Only Mode (factory default) The Automatic Start feature starts the vehicle automatically every one or two hours and runs for the preset Run Time. (15 or 25 min) Auto Start on Timer Mode: 1. Turn Ignition switch Off and wait for 3 seconds. 2. Turn Ignition switch On and Off three times ending with Ignition in Off position 3. Press the Valet switch immediatly after.
Manual Transmission Remote Start Features Model: Galaxy 5000/2000RS-DBP-M 1- Tach wire must be connected , The system must learn RPM. 2- Hand brake must be connected. 3- Door trigger must be connected 4- Clutch override installed NOTE: MUST USE RELAY, SEE PAGE 26.
Extended Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle. If RPM is selected Doors will lock when engine RPM exceed 2.5 times the idle.
System Installation 1. 2. Thoroughly read and become familiar with the installation instructions before beginning the installation. Review system contents: Main Unit 1 or 2 One-way 5 Button Remote Transmitters (varies by model) 1 or 2 Two-way 5 Button LCD Remote Transmitters (varies by model) Siren Shock Sensor Harnesses • • • • • • • 6-Pin starter harness 20-Pin main harness 4-Pin shock sensor harness 3-Pin door lock harness LED harness Override Switch harness 5 Pin antenna harness 3. 4.
Mounting the Control Unit The control unit must only be mounted in the interior of the vehicle. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system.
System Wiring 6-Pin Starter Harness Pin 1 RED WIRE A: Main Power Input A (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply. Remove the fuse until the installation is complete and all wiring is checked. Pin 2 RED WIRE B: Main Power Input B (+). Connect to the battery or constant power wire at the ignition switch with a minimum 25A supply.
Pin 12 GREEN WIRE: Negative Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open. Pin 13 WHITE/BLACK WIRE: Hood/Trunk Pin Input (-). Connect the to the hood/trunk pin switch. The switch must provide a ground output when switch is opened. Pin 14 ORANGE WIRE: Armed Output (-) 500 mA. The Orange wire provides a ground output while armed to activate a relay for starter defeat and anti-grind protection or window rollup module.
2-Pin White Connector: Located on the side of the main module. · Green WIRE - Parking Brake Input (-) For Manual Transmission and/or vehicles equipped with a turbo charged engine. Must be connected if using the Turbo Timer feature and/or Manual Transmission remote start feature. · Blue WIRE Turbo Timer cancel input for Manual transmission systems in Turbo Timer mode.
System Programming Entering System Programming This system is compatible with both the LCD two way transmitter or the standard transmitter, all system programming can be performed using either one. To enter System Programming: 1. Turn the ignition switch to the ON position. 2. Within 5 seconds, press the valet switch 5 times. · The siren/horn will provide three chirps/honks, indicating that you have entered Programming. 3.
Programming Branch Table Branch Feature Button 1 (default) Button 2 Button 3 1. Arm Mode Manual Arming Passive Arming 2. Auto Rearming Mode Disabled Enabled 3. Arming Chirps Siren Chirps On Siren & Horn Chirps On Silent 4. Ignition Door Locking On Off Set Override Code 5. Ignition Door Unlocking Unlock All Unlock Driver Only Off 6. Door Unlock Pulse Single Double 7. Door Lock Pulse Length 1 second 3 seconds 0.1 seconds 8. Passive Door Locking Disabled Enabled 9.
6. Door Unlock Pulse. Selects between one pulse or two pulse operation for the door unlock output. Many new import vehicles’ factory door locking systems require two pulses on the proper wire to unlock the doors. These systems can be interfaced directly without the use of relays or any additional circuitry by programming the system for double unlock pulse. 7. Door Lock Pulse Length. Selects between a 1, 3 or 0.1 seconds output for door locking and unlocking.
16. Auxiliary 3 Output Mode. Selects between Channel 3, Factory Rearm output, or third Ignition ouput. 17. Lock After Start. When selected, the doors will automatically lock after remote starting. Using button 3 disabled Mp Siren Mode. 18. Lock After Shutdown. When selected, the doors will automatically lock after remote shutdown. 19. Engine Run Time. Selects between 15 or 25 minutes for the remote start run cycle. 20. Automatic Start Mode.
28. Siren Mode. Selects standard siren (defualt) or MP Player Siren. 29. Turbo Timer. When enabled, if the emergency brake has been applied Ignition power will be kept On for a predetermined time (2 minutes Factory Default) from the application of the emergency brake. 30. Extended Parking Lights. When Enabled, upon Disarming Parking lights will turn On for 30 seconds 31. Warn-Away Pager Report. When Enabled, Warn-Away report will be sent to the pager.
Relay Diagrams Positive Dome Light Activation Negative Dome Light Activation Positive Horn Honk Negative Horn Honk Starter Defeat/Anti-Grind Negative Glow Plug Galaxy 5000/2000RS-DBP
Door Lock Diagrams Follow the diagrams below for connecting basic door lock systems. For Two Stage door lock systems (separately unlocks driver and passenger doors) see following pages.
Two Stage Door Lock Diagrams The Galaxy 5000/2000RS-DBP Series is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connected as shown below, disarming the system will unlock only the driver’s door. Pressing the disarm button again will unlock all doors.
Two Stage Door Lock Diagrams cont’d Two Stage Reverse Polarity Two Stage Adding Actuators Page 40 - Galaxy 5000/2000RS-DBP
Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference.
Starter Diagnostics Starter doesn’t start and parking lights flash: 3 Times - Engine RPM not detected (check tach wire and/or perform tach learn procedure) Hood Trigger is active (hood is open, wire is shorted to ground or pin switch is defective) 4 Times - Brake Trigger is active ( Brake switch input is shorted to ground or incorrect) 5 Times - Unit is in Valet (service) mode, and start is disabled.
Shock Sensor Adjustment Shock Sensor Adjustment: Clock wise increases sensitivity Galaxy 5000/2000RS-DBP - Page 43
Galaxy 5000RS-DBP Galaxy 2000RS-DBP Series ScyNet Port Green Emergency brake(-) Blue Aux Start (-) / Turbo Timer Cancel Antenna DBP Port Data Bypass Wiring Diagram Green Blue Shock Sensor Port Unlock output (-) 500mA Green/White Black/Gray White/Red Black/White Yellow Blue/Yellow Blue/White Blue/Orange Black Red Violet Green White/Black Orange Violet/White White/Violet Brown Gray White Brown/White LED Port Valet Switch Port Door Lock Port Main Harness Starter Harness Lock output (-) 500mA Brak
