IMPORTANT SAFETY NOTES We strongly recommend that anyone driving RC cars, or organising events, should obtain third party liability insurance. In the UK this can be done by joining the BRCA. www.brca.org This product is not suitable for children under the age of 14, without the direct supervision of a responsible adult. Select an area for assembly that is away from the reach of small children.
Step 01 A C x7 M3x 6 Csk Hd Screw B x1 M3x 25 Csk Hd Screw C x1 M3 Nut THREAD LOCK A B A A A A A A ! Leave screw C loose for now. D E D Step 02 A x2 M3x 5 Csk Hd Screw B C x2 E M3x 8 Csk Hd Screw C A x4 A D F M3x 6 Button Hd Screw E D x1 M2.5x 8 Button Hd Screw D F B B x2 M3x 8 Button Hd Screw F x2 Black Spacer 2mm www.racing-cars.
C Step 03 A D D E M3x 6 Csk Hd Screw B B C x4 B x2 M3x 6 Button Hd Screw C x2 M3x 4 Button Hd Screw D x4 M3 Thread Insert E x3 Ultra Short Ball Stud Low ! Use the M3x12 Cap head screw and washers to fit the inserts.Tighten the screw until the M3 thread insert D is pulled into the carbon fibre part as shown.
Step 05 A 1.00mm B x4 M2.5x 8 Button Hd Screw B x1 Plastic M3 Nut ! A Tighten screws A until the side link just begins to bind on the pivot balls. Then undo the screws 1/2 a turn. Ensure the side links can pivot freely. Also tighten screw C from step 2 in the same way. A A A B E A B Step 06a A x2 A M3x 6 Patched Grub Screw B D E x4 M3x 8 Button Hd Screw C x4 Black 2mm Spacer D E ! x8 M3 Thread Insert C D D C C x2 C Note the orientation of C/F mount.
A Step 06 A A x2 M3x 8 Button Hd Screw Step 07 A F x2 M3x 6 Csk Hd Screw B x4 D M3x 8 Csk Hd Screw C E B F C x1 F M3 Nyloc Nut D x1 B Black 3mm Spacer E ! x1 Ultra Long Ball Stud F Screw supplied with steering servo. x4 Black Csk Washer Set 90° at neutral. 05 www.racing-cars.
The Kit build is 5mm of spacers, and a 12mm screw as shown. The spacers adjust ride height. See P16 for more information. Step 08 A or x6 M3x 10 Csk Hd Screw M3x 12 Csk Hd Screw ! 1mm Spacer NOTE Use the 12mm screw when using 5-7mm of spacers. Use the 10mm screw when using 3-4.75mm of spacers. 2mm Spacer 2mm Spacer A A A Step 09 A A A x6 x2 C ‘O’ Ring 6mm C B C M3x 6 Button Hd Screw B A A x4 B Black 0.5mm Spacer C A ! Make sure the ‘O’Ring is fitted correctly. A www.
A A x2 Short Ball Stud Low B RH x2 C C M3 Nyloc Nut C LH A Step 10 B x2 Black 1.0mm Spacer D x2 D Black 0.5mm Spacer B D LH RH ! ! Step 11 A x2 The king pin may be a tight fit in the hub carriers. The hub carriers must touch the king pin stops. ‘E’ Ring B x2 King Pin Spacer B A B { A Silico ne 30000 OIL cSt 07 www.racing-cars.com e OIL Silicon St c 30000 { ! Oil King Pins where shown.
A D B Step 12 A x1 M3x 25 Button Hd Screw B B x2 ! ‘O’ Ring 6mm C x1 Black 4mm Spacer D x4 M3 Thread Insert E C E Use the M3x12 Cap head screw and washers to fit the inserts.Tighten the screw until the M3 thread inserts D is pulled into the carbon fibre part as shown. H H D D G x1 M3x 6 Button Hd Screw F F x1 ! M3 Nyloc Nut G x2 4 x 8 x 3 Bearing x4 Ultra Short Ball Stud Low M3x 14 Csk Hd Screw B These spacers must equal the ride height spacers.
Step 14 ! Shorter Note the ID mark on the turnbuckle. This side of the turnbuckle is the left hand thread. RH Thread ! 17.0mm Steering Link. Make 1. LH Thread Longer RH Thread LH Thread 20.5mm ! Track Rods Make 2. RACE TIP Screwing the sockets onto the turnbuckle, until no threads are visible, and then undoing them to the desired length allows for easier adjustment on the car. Greasing the threads will also help. ! 09 www.racing-cars.
A Step 15 A B x1 ø2.0 x 9.8mm Pin B x2 Diff Gear Shim C x1 ‘O’ Ring 5mm D e OIL Silicon t S 1000 c C x1 ø1/4” x ø3/8” Bearing ! Use a small amount of oil to hold the components in place during assembly. D Step 16 A ! x2 Diff Gear Shim B A C B x1 5 x 9x 3 Bearing C A Step 17 A e OIL Silicon t S 1000 c x1 ‘O’ Ring 5mm Use a small amount of oil to hold the components in place during assembly. B B B A A x4 B C Bevel Gear Shim B x4 M2.
A A Step 18 A A x4 B M2.5x 6 Button Hd Screw D B x1 M2.5x 8 Button Hd Screw C x1 M2.5x 10 Cap Hd Screw D x1 Thin Pin Drive Washer E x2 0.5mm Diff Spacer F x2 ø1/4” x ø3/8” FL Bearing F E ! NOTE: Kit Build 0.75 text UP. This gives a ride height of 4.5mm with the Pit Shimizu rubber tyres. See page 16 for more information. C F E A Step 19a A B x3 A M3x 14 Grub Screw 8.0mm x1 e OIL Silicon St c 0 0 0 2 1 Black 3.0mm Spacer ! Side Damper Make 2.
Step 19b Step 20 A B x2 M4x 8 Csk Hd Screw B x2 M4x Thread Insert C x4 2.5 x 6mmCsk Screw C C C ! Screws C can be found in the wing bag. A www.racing-cars.
C Step 21 A x2 M3x 10 Button Hd Screw B x1 C M3x 16 Button Hd Screw C C x3 ø1.5 x 11.8 Needle Roller A A B 1 Dot Low Position ! A x8 2.5 x 8 Csk Screw A A ! A 13 www.racing-cars.com Screws A can be found in the wing bag. 3 Dot High Position Select the correct body washer to fine tune the bodyshell height. Each incremental change is 1.2mm.
B Step 22b A x2 M3x 8 Button Hd Screw B D x2 M3 Nyloc Nut C A x2 D C D M3x 14 Csk Hd Screw x2 M3 Csk Washer Step 23 A x2 M4 Flanged Nyloc Nut B x2 M4 Nyloc Nut C x4 ø5mm x ø10mm Bearing D A x4 C Thin Pin Drive Washer B D C ! Adjust for minimum clearance, but free rotation. Do not overtighten. www.racing-cars.
! Step 24 A x2 Motor & pinion not included. M3x 10 Cap Hd Screw B x2 ! 3mm Washer C x1 Motor not included. M3x 6 Csk Hd Screw D x1 M3x 4mm Grub Screw ! B D A ! A B Reciever not included. ! Transponder not included. C ! 15 www.racing-cars.com Adjust the gear mesh to be as close as possible, without binding. ESC not included.
TRACK SETTINGS RIDE HEIGHT See Page 6 & 11 - Step 8 & 18 Front Ride Height is adjusted by adding/removing spacers under the wishbones. Removing spacers increases the ride height, adding spacers reduces the ride height. Rear Ride Height is adjusted by changing the eccentric on the rear axle. The greater the bearing offset towards the bottom of the eccentric, the higher the ride height. The greater the bearing offset towards the top of the eccentric, the lower the ride height.
ROLL SPRING See Page 4 - Step 6a Roll springs are used to control the car’s balance. A softer spring will generally give an easier to drive car, however, if too soft, corner entry stability will be compromised. Stiffer roll springs can be used to give a more aggressive steering car. The standard setting has the roll springs uncompressed and both just touching the lower pod plate when the car is stationary.
WHEELBASE See Page 6 - Step 8 The icon has the option to adjust the front wheelbase by moving the front end assembly. A shorter wheelbase will give the car more steering but will be more unstable, especially at high speed. A longer wheelbase will make the car more stable at high speed but will have less steering in the hairpins.
FRONT TRACK WIDTH See Page 14 - Step 23 Wider front track width will make the car easier to drive, provide less steering and give a slower response. Narrower front track width will make the car harder to drive, provide more steering and give a faster response. Using the option part U8123 and U8358 camber strap allows for a track width 6mm narrower when paired with the outer holes on the wishbones. Using a 3mm wide bearing on the inside of the wheel can reduce the track width by 2mm.
U1954 U4811 CR664 Pro - Thrust Bearing "1/8"" Silicone Nitride Ball (pk12)" Alloy Motor Spacer - 1mm - pk2 CR280 U7828 AX009 AX010 CR192 CR193 Aerox Alloy Servo Arm - Short 25T Futaba Aerox Alloy Servo Arm - Short 23T KO/Sanwa Alloy Servo Arm 25T - Futaba Short Alloy Servo Arm 23T - KO/Sanwa Short U8341 U8355 U8356 U8357 Gear Diff Spur Gear 60T 48dp - Icon 2 Gear Diff Spur Gear 88T 64dp - Icon 2 Gear Diff Spur Gear 80T 64dp - Icon 2 Gear Diff Spur Gear 64T 48dp - Icon 2 CR024 CR035 CR036 CR196 CR30
U8353 U4946 U7690 U7730 C/F Gear Diff Axle - Icon 2 U3582 Precision Balance Pivot Set Pro Ball Bearing 5 x 10 x 4 sealed - pr Pro Ball Bearings 1/4 x 3/8 x 1/8 Fl Shielded Pro-Ball Bearing 4x8x3 Sealed - (pr) U7897 U7918 U7919 U7774 Alloy Pivot Spacer 1mm - Atom 2 (pr) Alloy Pivot Mount - Atom 2 Alloy Pivot Block - Atom 2 M3 Alloy Washer Black 1.5 mm (pk10) U8065 U7825 M3 Alloy Thread Inserts - pk8 Titanium Pivot Ball 5.5mm Low (pr) U7943 U7944 U8123 U8124 U8358 Alloy Spacer Clip 0.
SPARES LISTS Bearings & Balls U1439 U2148 U3075 U4809 U4980 Ball Bearing - 5x9x3 Shield - (pr) Ball Bearing - 5x10x4 Shield - (pr) Ball Bearing - 4x8x3mm Red Seal - (pr) Ball Bearing - 1/4x3/8x1/8 Shield - (pr) Ball Bearing - 1/4x3/8x1/8 Flanged Yellow - (pr) Bodies & Decals MT011003 MT013012 MT015006 MT015007 MT015008 MT015009 MT017003 MT017006 MT017007 MT018009 TRG5015 TRG5016 TRG5017 TRG5026 TRG5027 TRG5060 TRG5061 TRG5062 TRG5063 TRG5064 U8135 Montech F1 Electric Car 1/10 F2011 Body Montech F1 Electr
SPARES LISTS CR316 CR320 CR321 CR322 CR327 CR328 CR329 CR507 CR508 CR509 CR510 CR511 CR512 CR513 CR515 CR664 CRW48060 U1954 U2135 U2810 U2811 U2812 U3582 U4112 U4328 U4808 U4811 U4855 U4861 U4946 U4970 U4974 U7690 U7709 U7730 U7774 U7825 U7828 U7829 U7883 U7897 U7918 U7919 U7943 U7944 U8065 U8104 U8120 U8121 U8122 U8123 U8124 U8125 U8126 U8127 U8128 U8129 U8130 U8131 U8137 U8186 U8353 U8358 Springs U4838 U4839 U4840 U4841 U4846 U7322 U7323 23 Alloy Button Head Hex Screws M3 x 10 pk10 Titanium Csk Hex Scr
SET UP SHEET Test Driver Driver: 18/2/22 Date: TRACK TYPE Grip Level High Medium Type Tight Open Mixed Condition Flat Bumpy Mixed Surface Tarmac (Asphalt) Qualifying: Final: Carpet Pit Shimizu BRCA Cleaner Brake Cleaner Cs High Grip mins Rear: 15 mins Front: mins Rear: mins Heating Temp Front: °C Rear: °C Additive Time Front: °C Heating Time Notes: 4 4.0 mm 2.0 mm Ride Height Droop 0.
